pull out faucet to garden hose adapter 3d models

Threaded adapter to connect a kitchen sink pull out faucet hose to a garden hose.

... home brewing forums, we discovered that the connector requires an M16x1.5 thread. I managed to design a custom adapter using Tinkercad and modified another one to create a garden hose fitting, which is the primary attachment point for the vacuum.

We have a big fancy Moen Pull down faucet and none of the included adapters connected to the hose where the sprayhead/fauct unscrews. Thanks to the vigilance of some home brewing forums I found that the connector is and m16x1.5 thread. I was able to...

I'm having trouble getting the OpenScad software to cooperate with this program, and I'm starting to think it's because I'm trying to use a water hose adapter that will connect directly to my faucet. This thing can be customized for any project I...

My sink faucet has 7/8-24 UNS thread type so I created an adapter to hook into a garden hose for Aquarium water changes. Internal bore is a cone for better flow and a stronger print. Print time was about 90mins. Hose threads fit extremely well,...

I designed an adapter that connects my Moen gooseneck faucet directly to a garden hose, allowing me to link my sink to a fish tank syphon/refill adapter. The unique custom thread on the Moen faucet required precise measurements, so I used calipers to...

Attach this adapter to standard 56/64-27 thread faucets after removing the aerator. Then, connect a standard 1-1/6-11.5 garden hose securely on the other end. To prevent leaks, install one or two additional o-rings if necessary. For optimal results,...

Was surprised that this didn't exist already. ...took me a while to get something that worked. I can tell you that from the faucet to the adapter, there is no leakage. ...Your mileage may vary.

Hose adapter useful for connecting a homebrewing wort chiller to a kitchen faucet that has a Delta sprayer head. The sprayer hose has a non-standard connector. Unscrew the sprayer head and connect this adapter to the sprayer hose. Use some silicone...

I was dissatisfied with the existing sink to garden hose adapters available, so I took matters into my own hands and created a new design that's built to withstand more wear and tear than its counterparts. This one is engineered to be less...

Remove the sprayer head and connect this adapter to the sprayer hose. Use a little silicone lube on the o-ring and washer for best results. Connects to standard garden hose with 3/4 - 11.5 GHT thread. ... Printed in PLA on a Prusa MK3, it seems to...

This threaded adapter converts from 3/4" garden hose female to 15/16" faucet male. Make sure to use a washer on the garden hose side.There are two version of the .stl file, one with a built-in supporting ring (break it off after printing), and...

I needed a quick adapter for my coil from a 20cm wide faucet head to a 7mm hose Figured someone else might need something similar one day so, enjoy :)

This is a removable Faucet to Hose Adapter. It is designed for my Aquarium Hose (6mm inner diameter). You need a sealing ring with a outer diameter of 20mm and a thickness of 1,5mm. ...You can glue the sealing ring to the adapter.

... ...Specifically designed for Gardena or comparable garden hose fittings, it ensures a watertight seal on the water tap. Simply attach this adapter to connect a Gardena garden hose (or equivalent) seamlessly to your faucet's 3/4-inch water supply.

I had found an adapter online, but it would set me back 25 euros. Too pricey, I decided to build one myself. It's programmed so you can easily adjust all the key settings. Unfortunately, it's not leakproof, requiring a piece of rubber for sealing....

- Extended 24mm part so it fits better for curved taps and holds better under pressure - Extended and increased hose part to fit 14mm diameter hose (base 13.8mm top 15mm, 20mm length) Thanks very much to CreativeTools.se

I printed an O ring for the adapter from 95A TPU using two walls and two top layers at 0,2mm layer height to make it squishy enough, i think i used 20% infill. Faucet_Connector_Gardena_Gasket02 from thing 5289793 worked fine for me as the O-ring. I...

Has a flat on both ends for a gasketFaucet Aerator adapter to Garden hose - 55/64-27tpi x5/8-11.5tpi. Designed this to go from my bathroom sink to a hose attachment for filling and draining my fish tank Gravel Vacuum for Aquarium Water Changer. So...

If you enjoy and are feeling froggy https://buymeacoffee.com/candidqualityBought a new bathroom faucet this weekend and needed another adapter to hook up to my fish tank. This is the smallest adapter I have ever seen for an aerator at 11/16"-27...

SW3dPS-faucet pull-out kitchen

To connect a Gardena hose connector to the faucet, you can use this adapter: https://www.thingiverse.com/thing:5580013 ---------- Dieser Adapter verbindet den Hahn (22 mm) einer Regentonne mit einem 1/2-Zoll Gartenschlauch. Der Adapter wird nur...

garden hose to 40mm drain pipe. ... garden hose connection to rinse a 40 mm drain pipe. ... fits almost all quick connect garden hoses.

... without any hassle. Before installing this DIY faucet to hose adapter, some users may need to remove the Delta Faucet aerator using a specialized removal tool, but this is a straightforward process that requires minimal technical expertise.

This is an accessory designed for connecting a standard garden hose to a pinlock fitting, perfect for various applications such as homebrewing and other activities that require secure hose connections.

Adapter to switch from 20mm garden hose to filter pump hose. 32mm. Useful for small pools that do not have an outlet for a filter pump but for drainage. You can use this outlet to connect the filter pump. I have printed this piece with PLA, but it...

We recently needed to connect a flexible hose to a standard water faucet in our office, so we designed this adapter in Autodesk Fusion 360 - which has an incredible thread-creation feature! Two hours later, the part was 3D-printed using PLA filament...

This was a combination of two items from Thingiverse: https://www.thingiverse.com/thing:551238 and https://www.thingiverse.com/thing:10189 The garden hose threads fit nicely on a real hose, and they can be printed without support at 0.2mm layer...

Instead of searching for a hard-to-find item at various hardware stores, we utilized 3D printing to create an adapter that connected a flexible hose to our office's standard water faucet. Autodesk Fusion 360, which features an impressive...