public domain 3d models

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

  ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...

This is because it is a slide on design to limit the complexity of the model.  INSTRUCTIONS: I tried my best to make this the simplest adjustable optic for nerf yet! As such it has only 3 parts that can easily be printed in under 2...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 7 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

... pictures are from Printable Heroes. They do not sponsor nor endorse these stands, but they do indeed offer a great variety of models —many of them for free. ...They do also have several, very affordable Patreon tiers —I suggest to check them out!

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

Http://www.Thingiverse.Com/Apps/Customizer/Run?Thing_id=507810 Instructions Using the Following Options: Custom_phone_width = 100 custom_bottom_fillet_resolution = 8 printer_tolerance = 0.4 stencil_vertical_position = 50 custom_case_pattern_thickness...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

The STEP file is included for easy remixing. Please post any makes and if you see a problem please post a comment. Updates: 4-30-2020: Thanks to feedback, I corrected the model for the base, the updated version is "6I". ...None of the other parts...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

 900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly.  If...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are resistant to oils, lubricants, and heat.The models are designed to fit an Eerie Tools SM-LTHM 7x14 lathe but...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...