ptfe tube for 3d printer

... press v slot roller spacer sleeves into the bracket. I used a small length of ptfe tube to hold parts aligned while inserting the bolt, which pushed the ptfe tube out the back. ...Install the nut and zip tie cables in place for a quick solution.

I used a small 6mm file to create flat spots which prevent the PTFE tube from moving or rotating. You can see this in the close-up photograph. I also lightly chamfered the ends of the tube with a drill bit. The lid is printed from...

Heavy filament spool on the Sidewinder X1 above was never a good idea (print quality was worse on taller parts, etc.) Also printhead kept pulling up slightly.This PTFE tube holder helps to avoid the problems and just leave the filament spool next to...

While using the original model for a few hours of printing, I noticed that the PTFE tube slowly moves upwards because of the retractions and inevitably gets caught by the extruder wheels. The tube is afterwards damaged in such a way that the filament...

This is a PTFE tube router for the Prusa i3 MK4 - MK3 / S / +, that allows you to use a dry box or a separate spool holder on your desk. ... It spits out the filament pretty much where it would come out of a spool mounted on the stock filament holder,...

Ender 3 pro filament guide for PTFE tube It works with Ender 3 pro genuine Bowden plastic extruder or metal extruder like in the picture.I prefer this design over the bearing roller type, less inconsistent friction.You should print like the last...

Using ideas from other designs, I added a funnel on the spool side to make loading filament easier and made sure my new 1/4-inch OD PTFE tube fits snugly into the bottom and stays there during printing. Then, I added a retaining ring on the bottom to...

... onto a printed part without using any plastic components. ...Secure the connection with an M3 screw tightened by hand, followed by an M3 nut for added stability. This setup is specifically designed to work well with the Tronxy X5S 3D printer model.

A simple quick release adapter for pfte tube that you can add to the back of the auto-rewind spool holder. Thread size is M10x1 (same as used in https://www.thingiverse.com/thing:3233579 ) Print instructionsCategory: 3D Printer Accessories

Simple adapter to use a M10x1.0 pneumatic fitting on the outgoing side of a BMG extruder. ... The standard PTFE tube clamp was really loose on my extruder. ... Needed parts: - M10x1.0 pneumatic fitting

Most common is PC4-01 (the 10mm variant).Also two variants exist for use without any pneumatic couplers, one with a loose, and one with a tight fit of the PTFE tube.All pivots can be printed without support for the “flat” variant. The “round”...

So by using these spools, the PTFE tube stays stuck in place, while filament flows smoothly in, simply guiding it along. Edit: I decided to use the Festo version for mine anyway, but with an upside-down twist. The tube makes feeding through on top...

I put my spools on a shelf, then had them feed in backwards. So by using these, the PTFE tube stays stuck, but filament goes in smooth, just guides it edit2: i decided to use the festo version for mine anyway, except it's upside down. the tube makes...

PTFE Tube Cutter

To modify the PTFE tube within the E3d hotend on Prusa i3 MK2 models and above, I've created a basic tool. First, make a clean cut along one side of the tube. Next, position the tool along the other side and cut a 50mm straight section. ...A scraper...

I've been experiencing a frustrating issue with the PTFE tube slowly creeping into the gear of my stepper motor due to over-retraction. ...To resolve this problem, I designed an innovative solution that prevents the tube from retracting excessively...

-Qidi X-Max -Qidi X-Plus ________________________________________________________________________ Since I don't feel like always ordering the PTFE hose from QIDI, I have now designed this easy way to cut your own PTFE hose. With the following...

So I designed 3 parts to adapt a PTFE tube to link the dryer to the FS Cover and keep the filament always out of humidity during printing. And you can let it in place after printing without fear of humidity. The FS Cover is the MK3S, with a M10x1.5...

And you can let it in place after printing without fear of humidity.The FS Cover is the MK3S, with a M10x1.5 and the PTFE is a standard tube (2mm in / 4mm out).edit :  I have replaced the blue PTFE by a transparent one, this is much better to...

This fix stops the PTFE tube from sliding back into the extruder gear during retraction. It's a quick 5-minute print, but still presents some challenges. Be sure you've calibrated your extruder and optimized flow settings to produce a successful...

This is where the PTFE Tubing Guillotine comes in - a simple yet effective device designed to make cutting PTFE tubing a breeze. To use it, simply slide your tubing through the hole until it's securely seated in the rear pocket and then slice. It's...

... ... It is made to hold two PTFE-Tubes with an outer diameter of approx. 4mm on a VSlot 2020 profile. For my printer setting the 10mm version is enough but I published a 20mm vesion just in case. ... Please let me know if the design works for you!

These are jigs specifically designed for cutting PTFE tubing used in E3D hot ends on Prusa MK3 and MK3s (and similar extruders). It utilizes a pencil sharpener blade from Mobius + Ruppert, available either as part of their sharpeners or sold...

Handmade PTFE Tube Halver Designed Specifically for Y-Adapter Dual Extrusion as a DIY Project

This is a Ptfe Tube Stabilizer for the Anycubic Vyper. ...Uses two M2x12 screws to assemble.

Custom Design (Remix of PTFE-Tube Holder) for somebody

As a result, one printer and spool holder are currently situated on the floor, prompting us to utilize a guide tube. However, a binder clip caused the tube to slide around, so we quickly created this solution to address the issue. Be cautious when...

This is a simple PTFE Tube clip for Ultimaker printers with dual or single extrusion. Used for 4mm PTFE tube (1.75mm filament). The clip fits very tightly, leaving the tubes securely attached. Designed with 1.6mm wall, print with a 0.4mm nozzle with...

I designed a holder, a roll and a cleaner with a screw connection a PTFE tube mount for the Anycubic i3 Mega S. You can put it on the right frame and it holds two tubes. I my case the PTFE tubes comes from the side out of the wall and I wanted to...

Creality Cr-6 se Ptfe tube