ptfe tube for 3d printer

This is an updated rendition of mhendricks' PTFE Tube Holder for MMU2 filament management, tailored specifically for utilization with 4 mm acrylic panels as opposed to the original 2.5 mm specifications.

... ...Gives a much better cut than using flush cutters. The opening for the blade is 1mm wide. Update: you can now open this in Thingiverse Customizer if you want to change the size of the PTFE tube or blade opening. Category: 3D Printer Accessories

Used a soldering iron to cut a notch in the filament door so a piece of PTFE tube can extend outside of printer and into a filament dryer. Prints fine with default Flashprint settings. Rotate model and use manual supports as shown. ... PC4-M10...

BOM: 2x M3x14 - to mount the Holder on the Printer 2x M3x20 - not needed but to secure the Sensor in place 4x Washer for M3 2x Nut for M3 - not needed but to secure the Sensor in place 1x M5x6x7 embedded Nut 1x M5-4mm tube fast connector...

Trim the other side with the outlet trimmer in the same way.You can print it without any support.(May 16, 2022 Update)Added trimmers with X-ACTO #11 blades, easily accessible around the world.Modified PTFE holder to prevent the tube from...

I just made the hole bigger to make room for a PTFE tube that can accommodate flexible filament. For anyone curious about the small clip opening, it's actually designed to hold an extruder tension holder in place. As you can see, I printed one out...

The solution turned out to be two different screws securing the PTFE tube (4mm outer diameter, 2mm internal) in place. The small metal screw used to secure the tube additionally is an M3 screw and provides extra strength to prevent the tube from...

PTFE cutter 82mm Category: 3D Printer Accessories

After struggling with a PTFE tube that kept sliding up and down despite using a few makeshift clamping aids, I decided to design a clone of the BMG extruder. Since I'm using the Sapphire PRO, placing the new clamp was a breeze - it's clear this...

I have used about 40cms of PTFE tube (http://e3d-online.com/RepRap-Spares-Mechanical/Bowden/PTFE-Tubing-3mm) and 2 Bowden couplings (http://e3d-online.com/RepRap-Spares-Mechanical/Bowden/Bowden-Couplings). I recommend some double side tape to avoid...

I also added some extra depth in each parking port, allowing you to leave some filament sticking out from your PTFE tube for easier grabbing when you need it again. The pushfit connectors I used are for 4mm PTFE tubes with a 4mm outer diameter for...

- Added screw connector for the PTFE tube. The screw connectors are from the _Locking bowden connector_ by Nicholas Christopoulos. The _External Filament Mod - Flashforge Adventurer 3_ also includes a useful guide for drilling a hole through the...

The first and last clamp must be flush with the side and back edges of the enclosure for even spacing and easy PTFE tube removal without removing both screws. These clamps have made it possible for me to use 5 different colors without needing a...

The tube holder now features a subtle chamfer, ensuring that a 4mm or 3mm PTFE tube can pass through without any obstruction from its edges.

PTFE Bowden tube cutter

For 4mm PTFE-tube. ...Holes for 4mm screw

This coupler is used to connect a piece of PTFE tube to the feeder, and have it go through a hole in the filament hatch, in order to use external filament holders with the hatch closed.I use it with the 1kg spool holder for monoprice voxel by Ryoichi...

... off. When printed properly, everything should have a friction fit. PTFE guide pieces press fit together, rectangular clips slide on the outside but are fairly snug, PTFE tubes are held in place but still slide in and out with little force. ...

A simple quick release adapter for pfte tube that you can add to the back of the auto-rewind spool holder. ...Thread size is M10x1 (same as used in https://www.thingiverse.com/thing:3233579 ) Print instructionsCategory: 3D Printer Accessories

I have added connectors to the PTFE tube and cable holder for plugging in fans, requiring two JST-XHP two-pin plugs. Two small holes are included for M2.5 set screws if extra tightening is needed. It should be helpful for anyone seeking a similar...

Allows for the adjustment of: The adjustment of text and its size.The size of PTFE tube end cap, along with how much filament is exposed under the end cap.There's more but you'd have to play with the geometry nodes node network (out of scope)...

... ...Within the guide itself, a piece of PTFE Bowden tube can be inserted, allowing for seamless extrusion. ...Although this design was created from scratch using Fusion 360, proper credit should be given to the original creator.

A quick print to cut the PTFE tube that goes inside the V6 hotend for the MK3S+ it's 42.3mm. ...This will get you close, I suggest you print it at 0.15mm layer height, this will be a better fit for the razor blade. 

For installing PTFE tubing through a delicate surface like plastic.

... FilaDryer S1 that allows the filament to curve gently instead of introducing sharp bends. ...It's angled as much as possible (21°) while still fitting into the stock outlet hole on the dryer, and uses a push fitting to hold the PTFE tube in place.

This is an original design inspired by https://www.prusaprinters.org/prints/2074-mmu2-filament-ptfe-guide-for-ikea-lack-table which didn't work out for me because it narrows at the end preventing the tubing from coming all the way through, and...

A openscad tube holder generator for ptfe tubes. Depending to your printing parameters and material you have to adjust the diameter. 3 mm tubes are very sensitive, but works with the right parameters fine too. Use something more flexible like abs and...

This is a PTFE tube router for the Prusa i3 MK3 / S / +, that allows you to use a dry box or a separate spool holder on your desk. It spits out the filament pretty much where it would come out of a spool mounted on the stock filament holder, so no...

Note: You may want to scale this up as the fit is a bit tight This is a PTFE Bowden tube clamp for 4mm outer diameter PTFE tubing. It was designed with a 0.4mm nozzle in mind, but due to small size, I recommend printing with a 0.2mm nozzle. The...

Note: You may want to scale this up 1% as the fit is a bit tight This is a PTFE Bowden tube clamp for 4mm PTFE tubing. It was designed with a 0.4mm nozzle in mind, but due to small size, I recommend printing with a 0.2mm nozzle. The bottom is tapered...