ptfe tube for 3d printer

### Features I made a jig to cut the PTFE tube for the nozzle of 3D printers X-smart / X-maker to a suitable length. ### Length of the cut tube - 36mm : X-maker - 45mm : X-maker / i-mate s ### Size of PTFE tube - Outer diameter: 4 mm - Inner...

Length of the cut tube36mm : X-smart (QIDI TECHNOLOGY)45mm : X-maker / i-mate s  (QIDI TECHNOLOGY)Size of PTFE tubeOuter diameter: 4 mmInner diameter: 2 mmMaterials NeededPTFE tube → AmazonScrew M3-10 x1Lock Nut M3 x1 → AmazonWasher M3...

Measuring and cutting the PTFE tube with just two hands can be a chore, so I made this jig which has two sections for blade to cut through the PTFE tube and make a straight cut. I measured the stock tube to be 80mm, this design is a hair above 80mm...

What you need more is: 2pcs of 4mm Pneumatic push connector https://www.amazon.se/MySixKeen-Straight-Pneumatic-Connect-Fittings/dp/B091B2K1Z8/ref=sr_1_12?dchild=1&keywords=4mm+pneumatic+push+connector&qid=1630773892&sr=8-12 About 900mm of PTFE...

This is an additional part for the Felix Tec serie 3D printer. I my case the bowden tube with de filament inside didn't has a good fixation with the extruder. It comes loose during retraction of the extruder. I have solved this issue with this new...

I created a holder specifically designed for 1/4 inch PTFE tubes, as I was frustrated with the excessive resistance and jamming issues caused by the smaller PTFE tubes that normally accompany the filament.

coupler for ptfe tube

Bracket TPU prints for easy handling, avoiding any printing issues. ...Note that the tube's knurled wheel side requires an adjustment on your 3D printer. ...Place it close to the knurled wheel, yet avoid direct contact.

It wasn't until I observed how other 3D printers produced a smooth, curved shape that I realized my own printer's spline was to blame. By incorporating this support, the filament remains perfectly positioned, allowing it to easily flow into the...

This tool assists with securely attaching a 1.75mm PTFE tube to the V6 pneumatic connector at the extruder's cold end head on the stepper side.\r\n\r\nFurthermore, it maintains stability and keeps the tube firmly in place even when the quick coupler...

... play on the PTFE tube on retractions. ...This clip replaces it and now the PTFE tube is secure, especially helpful for Bowden drive setups. Retraction distance was 4mm and now it's down to 2mm, a 50% improvement. ...Offered in 3 different sizes.</p>

3D Printer Extruder Motor Water Cooling - 2x5mm Silicone Pipes to 4mm Bowden PTFE Tube Clip. ... Designed for silicone pipes selling by Trianglelab with this set: Trianglelab Stepper motor water cooling upgrade kit for Nema17 motor.

PTFE tube tag for MMU3.Multi-colors are available. ...(Up to 3 colors)Sample gcode data uses fil.1(Base and Numbers) and fil.2(Background of Numbers).”Horizontal" means that the numbers are placed horizontally, and "Vertical" means that the numbers are...

I required a direct connection between a PTFE tube and my EZR Struder, but unfortunately, the extruder lacked a suitable interface for this purpose. ...In response, I took matters into my own hands and designed an adapter to bridge the gap.\r\n\r\nTo...

A guide that hooks onto the end of the x-axis and accepts PTFE tubes so that filament arrives near to the feeder intake.

saw the normal version of this and printed it out and within a few uses it broke. ...so i added some Structure and removed part of the Tube area so i could guide ptfe through the bend.

I designed a holder for 4mm OD PTFE filament tube that attaches securely to 13mm cable tubes. The prototype has been completed, but it remains untested due to the current inoperability of my printers at this time. Here's how I built the design using...

A precise fit for a 4mm tube is achievable. ...Inserting a piece of sponge will complete the process.

Airtight cap to close off the end of a PTFE tube coming from a drybox.Has space for the filament to extend into, so it doesn't get pushed back into the PTFE when capped.Designed for 4mm OD x 3mm ID tubes.Print Settings:0.20mm layer height10% Gyroid...

V1 a simple holder for IKEA cabinet. ...I was too lazy to drill holes through the box. Designed to be glued by double side tape.V2 designed for two screws since the tape didn't hold it well enough.Print instructionsDesigned for PETG

[2024.01.16 - New refined 1.3 version]- Decreased the freedom for tube flexing to about 50% (The original part has way too big, the tube never used even the half of the range). - Increased the side limiter surfaces' radii in the open section: the...

This is a simple jig for precision-cutting PTFE so it fits snugly in the hotend flat, resolving issues I've encountered with my E3D V6 Bowden jamming due to the PTFE tube not being seated properly. This solution has worked wonders. It's specifically...

The reason why I wanted this is because I am using a dry box with sealed PTFE tubes from it to the printer. To minimize moisture coming from the PTFE tube, I glued the start of the PTFE tube to the bottom of the Silica Box. This means that all the...

The reason why I wanted this is because I am using a dry box with sealed PTFE tubes from it to the printer. To minimize moisture coming from the PTFE tube, I glued the start of the PTFE tube to the bottom of the Silica Box. This means that all the...

I utilize 3mm PTFE tubing and discovered that most End Caps on Thingiverse are designed for 4mm, so I also wanted a secure catch for the filament. ...To address this issue, I created an Open SCAD design.\r\n\r\nThe Customizer allows you to create one...

and the inside is chamfered to allow the PTFE tube a controlled bend towards the appropriate reel of filament. If you prefer to use a wider PTFE Tube, the hole can be enlarged with a drill bit out to 6mm if you wish. The screw thread is nice and...

... always run a thin line of sealant around the grommet head the offer a near perfect seal. Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% Category: 3D Printer Accessories

I built a custom holder for a 4 mm PTFE tube. It attaches directly over the extruder motor as shown in the picture. The tube is secured by a M3 screw but the hole should be small enough to keep it in place on its own. When using a screw, be cautious...

Secure the PTFE tube firmly to prevent it from dropping.

Print Settings: Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: .12 Infill: 80 Notes: ABS material, Print all parts at one time. Post-Printing: Adjust part 1 to ensure a 2mm hole diameter for smooth lubrication...