ptfe ender 3 3d models

My objective was to keep the PTFE tube obstruction-free, allowing it to move freely as needed. Small 4mm cable ties hold the main cables to the clip securely. Two file versions are available for the push-fitting: 0.8mm and 1.8mm. View the...

I used esun PLA+ with the following settings: nozzle temp 220 °C, bed temp 60 °C, I printed at 60 mm/seg and first layer at 10 mm/seg. Set the part in cura as shown in the picture added. When you import to your slicer it will be rotated due design...

This is a Ender 3/5 Hotend PTFE tube fix, for later model hotend's without a flat base. Chuck Hellebuyck has a similar fix for older Ender 3 hotend's. USE: cut a 26mm+ piece of Capricorn Tube to go down to the nozzle, then place this part, then...

A simple holder made for ptfe tube that came with esun ebox lite that replaces stock spool holder. The hole is 6 mm in diameter and the tube snaps in it with a little bit of force. ...Probably won't work well for tall prints.

This PTFE coupler mount press fits onto the support of the Ender 3 (Pro) just above the Z axis stepper motor. It is currently designed to thread in an M10x1 PTFE tube coupler. No supports are needed when printed with the hexagons facing down. ...

a (remixed) guide for a standard ptfe tube (4mm) that could be inserted from the side

I swapped out the hole in the filament guide for a 4mm PTFE tube to get a snug fit. ...Print it at 100% and it should slide right on. This upgrade fits all Creality Ender 3 Variants: Ender 3, Ender 3 Pro, and Ender 3X.

Here is a modified filament guide for Creality printers such as the Ender 3. After printing a few times, I noticed wear on some parts due to filament friction. This modification redirects the filament directly into the extruder hole, reducing...

The length shown is short but of course the PTFE tube can go all the way to the filament drier.The tolerances are quite large because I was printing with a 0.8mm nozzle and didn't want to change it just to print this. ...A STEP file is provided if you...

You do have to be careful not to tighten these screws because you will put stress on your leadscrew and cause printing issues. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.12 Infill: 10% Filament:...

This Coupler Clamp makes sure your Stock PTFE-Coupler does not wear out on the Ender 3 v2 stock extruder! ... Printing: * 3-4 perimeters * No supports Installation: * Remove the PTFE-Tube from the Coupler if it's already installed * Make sure the the...

Ender 3 Palette 2 Filament Guide: A Step-by-Step Tutorial for Perfect Prints Every Time. When printing with PETG, I swear by a 50% fill and supports to achieve unparalleled strength around the hole. By laying horizontally, you can tap into the full...

... ...Within the guide itself, a piece of PTFE Bowden tube can be inserted, allowing for seamless extrusion. ...Although this design was created from scratch using Fusion 360, proper credit should be given to the original creator.

I created my own version since I didn't like how other people designed theirs. I wanted a roller to direct the filament but I didn't like other designs that had them in them. ... I used this filament guide along with mine...

This Dust Filter for Creality Ender 3 attaches to the filament motor and PTFE screw with ease, perfect for those who have nowhere else to put it. You won't need to detach this filter when changing filament. It works seamlessly with both 2.85mm and...

I've added PTFE tube support and cables, two connectors to plug in the fans. Two JST-XHP 2-pin connectors are required. There are also two small holes for captive M2.5 screws if needed to fine-tune them. Hopefully this will help someone looking for...

I designed this to snap on the extruder arm and help guide the PTFE tube with filament into extruder to avoid bending the filament (see picture without the guide) Support needed for printing the PTFE tube guide.

... it in place. See the pictures on how to cut the PTFE-tube. The tube can be a bit longer on the exit path if wanted. Tested with Ender 3 V2 and the official Creality aluminum extruder. ...Might also work with Ender 3/Pro but have not tested.

... a PTFE pass to insert a PTFE tube in the front exit of the box it will be well maintained and guide much better your filament from the box to your extruder without any untimely friction. for Ender 3 and other printer using the same aluminum profile

I've tried various filament guides for my Ender 3's extruder stepper motor, but I haven't been thrilled with any of them. DrStreet's design from https://www.thingiverse.com/thing:2873157 came closest to meeting my needs, but after two months of use,...

High-Quality Filament Guide for CR-10 and Ender 3 3D Printers with Smooth, Hassle-Free Teflon-Like Lubrication.

holder for a reverse-bowden fitting for the creality ender-3 frame. ...with this holder the filament roll can be placed sideways or in a dryer.petg → 250 celsius → 0.12mm layer

A small clip that makes uses of the extrusion clamp to keep a PFTE tube (1.75mm) in place. ...

Filament Guide for Ender 3 to prevent filament catching on Z lead screw. ...4mm hole for PTFE tube to guide filament from holder or drybox

Remixed to take a length of PTFE tube to prevent filament rubbing against the lead screw. Note: it's a tight fit for the PTFE tube, by design. Category: 3D Printer Extruders

Ender 3 pro filament guide for PTFE tube It works with Ender 3 pro genuine Bowden plastic extruder or metal extruder like in the picture.I prefer this design over the bearing roller type, less inconsistent friction.You should print like the last...

... between two plastic arms. The PTFE tube hole has also been reworked to allow the PTFE tube to extend all the way to the extruder gear. ... A longer screw is required to hold the bearing in place; a spare printer screw was used for this purpose.

I upgraded a M10 coupling to integrate a stop gap, allowing for a separate PTFE tube to be securely held within the CR-10/Ender 3 hotend. ... Full details can be found in this video: https://youtu.be/Fb4XMbZ0iA4 I also incorporated the HotEnd Prop...

I have added connectors to the PTFE tube and cable holder for plugging in fans, requiring two JST-XHP two-pin plugs. Two small holes are included for M2.5 set screws if extra tightening is needed. It should be helpful for anyone seeking a similar...