ptfe coupler 3d models

Simple PTFE coupler. Print vertically, to ensure hole is round.

I created this Mini/+ PTFE tube to filament sensor coupler to more securely attach the filament dehydrator to the filament sensor.An M3 screw is used to attach it to the filament sensor.

I made this coupler with a 4.1mm inner diameter because it was too tight for mine at 4mm.

Just some simple labels to hang on your PTFE couplers if you're using these with a DIY filament drying box, to easily identify which spools are which material.

Also, I wanted to print flexible filaments and with the large gap, it promoted jamming. On a secondary note, I wanted to design some threads, both internal and external AnetA8_M6_PTFE_Coupler_Guide.stl is a fully parametric filament guide that allows...

Also, I wanted to print flexible filaments and with the large gap, it caused jamming.\r\n\r\nOn a secondary note, I aimed to design some threads, both internal and external\r\n\r\nAnetA8_M6_PTFE_Coupler_Guide.stl is an advanced parametric filament...

This is the coupler from the video where I walk you through the PC4-M10 PTFE Coupler to allow the 1.8mm ID PTFE tube to be used to constrict the melted filament as it is retracted out of the hot end to a diameter that will fit within the rest of the...

A remixed PTFE Coupler that sits directly on the main frame of the MK3S. ...Can be used for a reverse bowden filament guide setup.

This is a very simple coupler for joining 4mm ptfe tubes using PC4-M10 pneumatic couplers. ...I use these to quick connect tubes from my repbox straight to my printer or MMU2S.</p> Category: 3D Printer Accessories

Yet another coupler for PTFE (Bowden) tube, but from Junk-Tec engineers. No threads, no screws, just friction and power of your hands. Print it on the smooth surface. For friction adjustment use extrusion multiplier. ... ATTENTION: this coupler...

 Fusion 360 to the rescue!!!Due to the global supply chain making everything ridiculously expensive, I designed this M6 coupler so that I can use both the stock PTFE tubing that came with my Ender 3 (or any printer for that matter) alongside a length...

This is a super easy connector for linking 4-millimeter PTFE tubes with PC4-M10 pneumatic connectors. ...I utilize these to rapidly attach tubes directly from my repbox to my printer or MMU2S.

Sunlu S1 filadryer filament guide that can be printed on the side for increased strength from layer orientation and can be fitted with an M10 PTFE coupling.

For those who keep getting the end of their teflon tubing to melt, causing the filament to clog, some people have started buying Capricorn PTFE filament as a solution. ...I'm guessing that anyone who cuts a new end to their filament is likely replacing...

I increased the size of the hole that the PTFE coupler goes into so that it will fit an M10 threaded coupler such as this one:...

This is a remix of the original prusa i3 MK2 extruder body to allow a PTFE coupler to be added so that you can use the 3D Chameleon MK2. ...Supports and brim are designed in, so there is no need to add additional supports

https://www.thingiverse.com/thing:4441076 I remixed brentwerder's Rear PTFE coupler for use with the M5 heatserts I had on hand (McMaster-Carr part number 94180A361) by adding a bit of material around the holes and on the coupling face. ... Thanks to...

I've built the TZB MMU2S filament buffer, which demands 10 PTFE couplers with R1/8 thread. In my setup, I need to be able to rapidly connect and disconnect the five tubes, so I designed this solution where all the tubes are clamped simultaneously...

... part to let your PTFE have something solid and square to hit against without restricting filament travel. To avoid this problem, I use a heat-set nut so that the coupler can thread onto the existing PTFE that connects the MMU to the Mk3's extruder.

For other Prusa MMU stuff: https://www.thingiverse.com/AbeFM/collections/abes-mmu2-stuff I find that when I have filament from one PTFE, and I feel it into a second one, after the print gets going these can bump together and cause friction issues....

This version uses a heat-set nut so that the coupler can thread onto the existing PTFE that would connect the MMU to the Mk3's extruder. Post-Printing Don't forget to set your nut! I use a soldering iron. Check for expanded plastic blocking the hole...

Bill of materials*: 200mm PTFE Tubing (2mm ID, 4mm OD) 5x PC4-M5 Pneumatic Fittings 5x M5 Threaded Inserts *You may be able to find these parts for cheaper online. The provided links are the specific parts I had laying around. Printing...

Bill of materials: *200mm PTFE Tubing (2mm ID, 4mm OD) from Amazon 5x PC4-M5 Pneumatic Fittings from WMYCONGCONG on Amazon 5x M5 Threaded Inserts from Products Insert on Amazon You may be able to find these parts for cheaper online. The provided...

For the original model and instructions, visit their Thingiverse post. Like many MMU2S owners, I had a few issues with the PTFE tube setup - in particular, their "sandwich" clamp design that fails to put pressure on all 5 tubes. iwagner's excellent...

A quick and dirty remix – I found it difficult to add the magnets to this amazing print so made a stable structure for it to sit in.Convenient to place the coupler in this stand, add magnets then hammer/glue in.

... the CR-10's innovative design by merging the extruder and hotend into a single, streamlined unit. ...In this vision, I'll eliminate the traditional dual-piece setup, instead routing the PTFE tube directly from the extruder to the nozzle in the hot end.

This stops the PTFE coupler from being lose and going back and forth. It has a thickness of 2.18 and fits on the coupler that comes off the extruder.&nbsp;I am sure there are some of these out there but I was having trouble finding one so I just made...

To be used with PTFE couplers with an M6 thread.

A small removal device for the hot end isolator of the Ultimaker 2 to get the PTFE coupler out.

This is a PTFE PC4-M10 Adapter for the SeeMeCNC EZR Struder to allow a bowden coupler to attach to the in feed of the EZR. ... This allows the 3D Chameleon to load and unload the filament automatically.