ptfe 3d printing filament

This is a custom 6mm OD PTFE/Teflon filament tube coupler I designed specifically for joining two pieces of 6mm OD filament tube together seamlessly. The filament tubes press-fit snugly into the coupler without any deformation, ensuring a secure...

Please find the free models here: https://www.printables.com/model/374779-ender-3-v2-dual-extruder-filament-guide-for-ptfe-t _____ Used the original filament Guide from Soda Surfer / RedSoda for 2 years and recently upgraded to a dual extruder. As my...

Primarily, it prevents wear to the filament sensor housing by guiding the path of the filament with a length of PTFE tube on the input. It also helps reduce air exposure to humidity-sensitive filaments like PETG and Nylon by keeping the filament...

Using ideas from other designs, I added a funnel on the spool side to make loading filament easier and made sure my new 1/4-inch OD PTFE tube fits snugly into the bottom and stays there during printing. Then, I added a retaining ring on the bottom to...

This is a custom 4mm to 6mm OD PTFE/Teflon filament tube coupler/joiner designed to join two pieces of filament tube together seamlessly. It expertly connects one piece with a 4mm OD to another with a 6mm OD, ensuring a snug fit without any...

......A PTFE tube, cut from a CR-10 spare part, was being used. There's a slight issue when removing filament as the blob portion won't retract back through the PTFE tube. ... A few upgrades for the CR 10, including some hop-ups, are available on eBay UK.

... for those without a spare wine. ...I've printed it in ABS, but its design accommodates other plastics as well. If geometry issues prevent the PTFE tube from fitting, try using a 4mm drill bit. ...For the "screw" component, supports are necessary.

This piece achieves several goals: it increases filament clamping force by shortening the spring gap a couple of mm, making it equivalent to adding a few washers to the stock setup; it allows for flexible filaments by reducing the likelihood of them...

Simple adapter to put on your 2020 extrusion above your filament runout sensor to attach a PTFE tube to the Creativity Elf printer when you have a direct drive extruder. ... It helps get the filament from the stock spool holder to the head.

The original design with only a central filament guide restricts usable print volume, since the filament gets severely bent when the extruder is near the top of the enclosure and moves along the X-axis. To overcome this limitation, I plan to upgrade...

I also add a PTFE pass to insert a PTFE tube in the front exit of the box it will be well maintained and guide much better your filament from the box to your extruder without any untimely friction. ...for Ender 3 and other printer using the same...

https://www.youtube.com/watch?v=eBnAwzM1tyA BOM: - Spool holder for Rubbermaid 21cup container from rc101 https://www.thingiverse.com/thing:2185015 - PTFE bowden fitting port + Nut from dottom22 https://www.thingiverse.com/thing:2139021 - PTFE tube...

This filament guide is specifically tailored for use with the slave struder found on https://www.thingiverse.com/thing:3437372. Within the guide itself, a piece of PTFE Bowden tube can be inserted, allowing for seamless extrusion. ...Although this...

Simple Filament Sensor Holder for 6mm PTFE tube. Designed for ASWX1 but may works on other printers e.g. Alfawise, Creality. I used the nuts from the orginal spoolholder to screw it in. Currently there is one version which can hold the Sensor...

Based on the original dragon design and ornament remix by cyclone (thanks for the awesome dragon design!), I created this filament pass through to accept and operate with 4mm PTFE tubing. It has a simple clip to keep the guide from popping out. All...

Remix to run the PTFE tube horizontally

for 4mm PTFE Tube. use a 4.1 mm Drill . ...

Run the PTFE tube parallel to the ground.

This coupler is used to connect a piece of PTFE tube to the feeder, and have it go through a hole in the filament hatch, in order to use external filament holders with the hatch closed. I use it with the _1kg spool holder for monoprice voxel_ by...

This kit enables PTFE filament guide installation on various printers, such as the CTC Creator Dual, WanHao Duplicator 3 & 4, FlashForge Creator I, II, III & X, and MakerBot Replicator 1. It optimizes for spring-loaded Drive Blocks but may work with...

This PTFE coupler mount press fits onto the support of the Ender 3 (Pro) just above the Z axis stepper motor. It is currently designed to thread in an M10x1 PTFE tube coupler. No supports are needed when printed with the hexagons facing down. ...

After mounting my filament holder on the control box I noticed some extrusion issues associated with the filament causing too much force perpendicular to the extruder for it to pull filament through effectively - This part is designed to be used in...

After mounting my filament holder on the control box I noticed some extrusion issues associated with the filament causing too much force perpendicular to the extruder for it to pull filament through effectively - This part is designed to be used in...

To assemble, simply reduce the diameter of your PTFE tube using a knife and screw it into the nut, ensuring the filament flows unobstructed through the holder. Once complete, attach the cap securely in place. Two versions are available: one with...

Then I found the Filament Guide w/ Locking PTFE Coupler by FedorSosnin and thought, "I really love that idea for easy installation and making it easier to change filaments!" Then I thought, "What if I combined them?" So, I imported both files into...

The PTFE tube should be approximately 35mm long, and its flexible outer end will help when the filament roll oscillates. The Bowden tube should be installed after the guide is attached to the machine, a relatively challenging operation due to its...

The output is tangential to the coil which allows the filament to unwind much more naturally than with the original output.It is necessary to glue the part with a heat resistant double sided adhesive, this avoids screwing the part and weakening the...

ive recently built new enclosures for all my printers an a couple of them ended up being pretty tight between the top of my delta printers an the top of the enclosures, the tops are on hinges an i can lift them but that doesnt really help with...

It will fit with my Cable Chainlink (https://www.thingiverse.com/thing:5202027) and supports PTFE Tube connection (to my Filament DryBox). BOM: 2x M3x14 - to mount the Holder on the Printer 2x M3x20 - not needed but to secure the Sensor in...

I put my spools on a shelf, then had them feed in backwards. So by using these, the PTFE tube stays stuck, but filament goes in smooth, just guides it edit2: i decided to use the festo version for mine anyway, except it's upside down. the tube makes...