ptfe 3d printing filament

Ender 3 pro filament guide for PTFE tube It works with Ender 3 pro genuine Bowden plastic extruder or metal extruder like in the picture.I prefer this design over the bearing roller type, less inconsistent friction.You should print like the last...

......I've been using this for years anywhere that the printer has a PTFE tube as the inlet for filament and it makes life much easier when you're feeding in new filament.Printing is simple, print the large end of the funnel face down. No supports needed.

This is an air injector to achieve air flow through teflon (PTFE) bowden tubes for filament on 3D printers. It is designed to allow air flow only in direction of the extruder and not towards the filament roll. This is achieved by two factors: On the...

Printer Settings Printer Brand: Prusa Printer: Prusa MK2 Rafts: Doesn't Matter Supports: No Post-Printing There's a 0.2mm single layer print at the bottom of the filament entry hole, making it print-friendly. ...You need to remove this single layer...

... box or a separate spool holder on your desk. ... It spits out the filament pretty much where it would come out of a spool mounted on the stock filament holder, so no problems with the extruder hitting or interfering with it while printing tall stuff.

... in. ...To guide the filament into the printer, I employed a 2x4 PTFE tube along with a push-through fitting.\r\nThe images depict a previous iteration of it; I haven't printed the updated one yet.\r\nFeel free to try it out and modify it as needed.

Insert a PTFE liner into this filament guide to prevent damage and ensure a smooth flow of flexible filaments. Drilling out the guide may also be necessary if the liner won't fit. The guide should be placed directly inside the extruder for optimal...

I have used about 40cms of PTFE tube (http://e3d-online.com/RepRap-Spares-Mechanical/Bowden/PTFE-Tubing-3mm) and 2 Bowden couplings (http://e3d-online.com/RepRap-Spares-Mechanical/Bowden/Bowden-Couplings). I recommend some double side tape to avoid...

This is an improved version of Bu66as's filament tube cap https://www.prusaprinters.org/prints/70444-petg-tube-cap-for-ptfe-4-mm-odI used the original model as a starting point and redesigned it with these improvements:Optional o-ring slot for better...

This is a tweak of a printed part downloaded straight from Prusa 3D themselves which adds an endpoint for a regular PTFE Bowden tube at the top of the printer frame, above the PSU.Post-PrintingVitaminsYou'll need approximately 60cm of regular PTFE...

This spoolholder included a swiveling part with a PTFE tube towards the filament sensor to aim for a neater routing of the filament. Unfortunately the filament sensor did not allow for a good fixation of the PTFE tube, hence it was pushed out. In...

PETG filament flows smoothly through a Prusa feeder designed specifically for PTFE tubes featuring an M6 thread. ...A 20% density setting is chosen to ensure optimal material usage.

Filament sensor holder for Qidi I-Mate S with 4 mm PTFE tube connection TPU Sensor: e.g. ... https://www.amazon.de/gp/product/B07FSXFPLD/

Remix from @laubed job. ... I do this for insert a PTFE tube,because original one was too small also for a 1,75mm filaments.

This a little redesign for a filament guide from CR-10 filament guide by Greg191134. ... I've modified the filament guide to insert a PTFE connector in the axis of the extruder. ... The result is really clean and perfect !

After installing my filament holder on the control box, I noticed some extrusion problems linked to the filament causing excessive force perpendicular to the extruder, making it difficult for it to pull filament through effectively - This component...

A simple print that is used to close the end of a PTFE/Bowden tube. The special feature: The plug has a buffer for the filament so that you can easily pull it out of the tube after you pull the plug off.I use this plug with my (dyna) dryboxes. I no...

 To avoid damaging the clamps or to get a too big bore, I recommend to clamp the drill in a vice and to calibrate the fitting manuel.For shown support ring where end of tube is fixed, follow the link: Support ring to fix and plug PTFE tube if...

Two PTFE couplings with an M6 thread can be screwed in afterwards to attach a PFTE tube on both sides and easily guide the filament through the enclosure wall.Wall thickness: 18mmScrew hole diameter: 16mmFilament diameter: 1.75mmTo learn more about...

I also added some extra depth in each parking port, allowing you to leave some filament sticking out from your PTFE tube for easier grabbing when you need it again. The pushfit connectors I used are for 4mm PTFE tubes with a 4mm outer diameter for...

... with a very bad access to the entrance (my printer is in a closet for instance) The holder is reinforced with metal 10 mm thick threaded rods. ... Printed with 123-3D orange PLA 195 degrees celcius extruder and 60 degrees celcius bed temperature.

Print Settings Rafts: No Supports: No Post-Printing It's a little snug, depending on your PTFE. You could scale it slightly (horizontal expansion, etc), but I just touch it with a heat gun, hoping it'll contract and "squeeze" a bit more. ... Category:...

Print Settings Rafts: No Supports: No Post-Printing It's a little snug, depending on your PTFE. You could scale it slightly (horizontal expansion, etc), but I just touch it with a heat gun, hoping it'll contract and "squeeze" a bit more. ... Category:...

I made the inside stepped, so the PTFE tubes all hit a hard stop and the filaments are loaded through a conical opening to make inserting easier and also to reduce the friction. It works really well. I have also included some 8cm spacers that...

... a variant. then screw on your pneumatic hose fitting and plug in the hose. note up to 10 cm you can use any pneumatic tube 4/2 mm (4 external 2 internal) plus I recommend using PTFE tube as this does not create any friction with the filaments,

I added a 10mm PTFE coupler threading, so that instead of the threaded cap, you thread in the coupler, insert some PTFE tube and have some strain relief as well. Put some foam / sponge into the small cylinder and then screw in the coupler. You...

This is a remix: http://www.thingiverse.com/thing:3134389 Thanks to NONADS69 for its design. Guide/Organiser Prusa MMU2 PTFE Tube on IKEA Lack table. Allows PTFE Tubes to be held in place and shifted on request as well as quick Filament removal.

I created this remix to overcome the issue of 2mm holes jamming when pulling filament through. PTFE proves to be highly effective in resolving this problem. To use PTFE as guides, cut small sections from a ptfe tube. The hole diameter is 4.35mm; my...

So by using these spools, the PTFE tube stays stuck in place, while filament flows smoothly in, simply guiding it along. Edit: I decided to use the Festo version for mine anyway, but with an upside-down twist. The tube makes feeding through on top...

This coupler is used to connect a piece of PTFE tube to the feeder, and have it go through a hole in the filament hatch, in order to use external filament holders with the hatch closed.I use it with the 1kg spool holder for monoprice voxel by Ryoichi...