psu mount 3d models

Recent AM8 Build Gets Easy Upgrade with Simple PSU Mount and MKS Gen L Installation.

Some DIN Rail mounting plates for Meanwell PSU´s

A mount to attach a Dell PSU HA180PM180 to a 75mm VESA plate. The PSU is not fixed and very loose for quick removal. ...Use double sided duct tape or remix it to make it tighter.&nbsp;</p>

The OG Ender3 must have a different PSU than the Pro as Kinkinpower's mounting pattern didn't quite match my PSU. ... This remix is compatible with my standard Ender3 PSU in addition to moving the vent slots up a bit so as not to be obscured by the the...

In this scenario, the PSU must be mounted off-center from the leg to allow clearance for the little tab on the bottom of the power supply that holds the mounting screws. The holes on my Prusa PSU have a depth of 5mm. Therefore, the screws used...

I designed this simple mount to ATX PC PSU onto a 20 by X extrusion. I use modified ATX PSUs for all my printers, so this was direly needed ;) The print is pretty straight forward. Just print it. No supports nothing. ... The holes fit M5 screws.

Since the temperature of the power supply unit (PSU) remains uncertain, printing with PETG material is recommended if available, although PLA should also suffice due to its relatively low heat output. ...To ensure maximum structural integrity, it's...

1 needed to attach my main monitor PSU to the table to avoid kicking it.It should work for any PSU with 67.5mm width and 39mm height.Im my case a printed 2 of them.The Screws are normal wood screws

... I make this? I made a turnstile for my Ultimaker, and I needed a way to hold the PSU in place so it did not fall and unplug itself while turning the stage. I will post my build on my website, since it uses parts outside the scope of Thingiverse.

After replacing the default 24v PSU on my TronXY X5SA with a Meanwell unit I found that the Meanwell is slightly shorter and wider than the default budget PSU. This shroud will attach the the Meanwell, provides room for a power switch, and attaches...

After replacing the default 24v PSU on my TronXY X5SA with a Meanwell unit I found that the Meanwell is slightly shorter and wider than the default budget PSU. This shroud will attach the the Meanwell, provides room for a power switch, and attaches...

To mount the bracket, first locate the screw holes on the case that correspond to the bracket's mounting points. Next, place the bracket over these screws and secure it in place using the provided screws. ...Make sure the bracket is level and firmly...

In an effort to make the Prusa Enclosure less deep I mounted the PSU to the side instead of the back.If you want to do this I feel obliged to say that, minor as it may be, this causes irreversable damage. Namely a hoop for a tie wrap on the metal...

I'm Installing a 12V PSU Mount on My IKEA BEKANT Desk for Sim Racing Bass Shakers.

Mark the two mounting holes as you did with the lower portion, remove the Supernight, and drill the holes for the top. Secure the top in place and drop in the PSU once it's locked in. Your installation is now complete! ... Hardware needed: • 5 M3x12mm...

Quick Detachable PSU Mount for Ender 3 *The one in the photo had some modifications with power tools, all changes have been updated in the files. I wanted to be able to remove the PSU when I placed my Ender 3 in an enclosure, but also place it back...

I haven't found what I've needed, so I designed this extra rigid PSU mount for Ender 3 Pro (Meanwell PSU). It slides inside 4040 extrusion with a tiny bit of force to ensure there's no wobble at all. There's a plenty of room between 4040 extrusion...

PSU receptacle/inlet housing for mounting on a 3D printer enclosure or cabinet. ...My Meanwell PSU from my Ender 3 V2 did not have an attached switch.I wanted to be able to attach it to the Aluminum 2020 extrusion I made most of my enclosure from, so...

If your 3D printer suffers from unpredictable Power related errors after an hour or more into a print job, your power supply unit (PSU) might be overheating! Keep it cool by attaching a USB powered fan to the PSU with this magnetic fan mount, without...

... is a mounting bracket for an IEC C14 three-pin euro chassis with integrated switching functionality. ...The mounting hardware utilized features M4-sized fasteners, specifically an M4x16 screw, which securely attaches the device to a standard profile.

!!! ...PLEASE BE SAFE AND MAKE SURE THE SCREWS DO NOT TOUCH THE INTERNAL CIRCUITRY OF THE PSU !!! To mount my 30A PSU under my HyperCube printer I designed these brackets.

To mount my 30A PSU under my HyperCube printer I designed these brackets. Print instructionsCategory: 3D Printer Parts Summary !!! PLEASE BE SAFE AND MAKE SURE THE SCREWS DO NOT TOUCH THE INTERNAL CIRCUITRY OF THE PSU !!! To mount my 30A PSU under my...

... MK3s. ...There are 2mm indentations for screws for mounting to the PSU and 1mm indentation on the other side for m3nS nuts for mounting to the frame. There are two files. ...Use both or risk destroying your prints from vibrations and resonance.

When combined with the mentioned project, it sits slightly low due to the side panel that integrates the PSU mount. To overcome this issue, double-sided tape was used for a quick and easy installation, but drilling holes and utilizing a nylon flat...

So I decided to use a 5V USB fan to cool it down.\r\n\r\nSince the PSU is positioned vertically, I came up with this custom mount to place the fan near the PSU while occupying minimal space possible.\r\n\r\nI've been using a 120x120x25mm USB fan...

Those pieces can be screwed in place on a IKEA Lack table leg to hold the PSU with around 5mm space between the inside of the leg and the mounts. This is a good solution if your Lack enclosure has sides that overlap the table legs. This one is also...

To solve this problem, I was looking for a new fan to install inside the PSU but found an old 120mm PC fan and a mount for the original Ender3 PSU online (https://www.thingiverse.com/thing:3359622). However, the Ender3 Pro comes with a Mean Well PSU...

Print two PSU Secures to the mounts with 4 m3x8 cap screw. The mount then is secured to the enclosure by some screws I found in my garage. The center access hole is 8mm and the three through-holes are 5mm. Features a chamber bottom and m3 holes...

... within the printer's interior. The mounting hardware includes screws and clips that are precision-crafted to fit snugly into the PSU's existing holes and grooves, guaranteeing a secure hold on the 40 mm fan even during intense printing sessions.

... is designed to be compatible with this din rail clip . https://www.thingiverse.com/thing:3531692 The clips mounts less tight as A, such that moving the mounted PSU is possible when applying a small amount of force All holes are M3 countersunk.