psu mount 3d models

The PS Eye mount is specifically designed to attach snugly to the Anycubic Kossel's Power Supply side, securing it in place with a tight clip. It seamlessly integrates into the 120v/240v switch and fits firmly into the PSU lower housing. ...The bracket...

This is a rather simple print to mount the power supply that came with the Creality Ender 3 Pro in the back under the heat-bed. It prints comparably quickly and doesn't need any supports. This thing leaves the psu terminals exposed! Please also...

... his PC in his RV. Based on measured PSU dimensions: 86x150x188 [mm] I recommend printing in the orientation pictured and use supports. Other settings are up to you, but I would use at least 1.2mm wall thickness and 40% infill density. ...

Check out this straightforward Wall Mount design specifically tailored for your Prusa MK3 PSU. ...I'd love for you to take a look at my latest creation, the TOP Holder, which is available on Thingiverse - search for 3462040 to find it!

... RV. ... Based on measured PSU dimensions: 86x150x188 [mm]. Fits perfectly. I recommend printing in the orientation pictured and use supports. Other settings are up to you, but I would use at least 1.2mm wall thickness and 40% infill density. ...

... RV. ... Based on measured PSU dimensions: 86x150x188 [mm]. Fits perfectly. I recommend printing in the orientation pictured and use supports. Other settings are up to you, but I would use at least 1.2mm wall thickness and 40% infill density. ...

To address this issue, I redesigned the original Prusa MK3 PSU cover to allow it to be mounted on the side of the closet instead of being confined inside. Before you start printing, make sure to drill holes for the PSU cables so they can pass...

... dust cover secured by magnetic strips or clips. To ensure a secure fit, longer PSU screws are included for mounting purposes. ... Feedback on this model would be greatly appreciated as I am currently unable to print it due to an inoperable printer.

i changed the mount so it mounts on the side of the psu to the wall, rather then the back to the wall this is a remix of https://www.thingiverse.com/thing:3747148 ENDER 3 MAX VERSIONS PRINTING. https://youtu.be/Oc7JB86vo0g (bottom) ( time lapse ) ...

Once the mounting position is determined, attach the PSU securely using anti-vibration mounts or rubber grommets to minimize vibrations and noise. Next, connect all necessary cables, including power leads, fan connections, and any additional control...

This is a rather simple print to mount the power supply that came with the Creality Ender 3 Pro in the back under the heat-bed. It prints comparably quickly and doesn't need any supports. This thing leaves the psu terminals exposed! ...Please also print...

i changed the mount so it mounts on the side of the psu to the wall, rather then the back to the wallthis is a remix of https://www.thingiverse.com/thing:3747148if you want to use the same power plug as me -                                          ...

Pegboard mount designed for a 19V 2.1A power supply similar to this model (https://www.banggood.com/19V-2-1A-50-60Hz-AC-DC-Switching-Mode-Power-Supply-100-240V-EU-US-Plug-for-TS100-Soldering-Iron-p-1268737.html?rmmds=myorder&cur_warehouse=CN).

The fan clicks securely into the fan support that is cleverly mounted to the PSU using 3D-printed rivets. The silent fan cover effortlessly clicks over the fan, providing protection for both the fan and your fingers from damage. This design has...

I'm over the moon to finally receive my new black delta PSU, and I couldn't be more thrilled - those annoying vibration sounds when printing are now a thing of the past! To get it up and running, I had to design a small but crucial bracket that...

I need a simple way to attach the Anker 5 Port USB PSU to my nightstand so it's easily accessible while I sleep or watch TV.

Two straightforward and easy-to-assemble designs to install the PSU box that comes with the Wanhao I3 2.1 underneath a table.

Enter PSU width and height, allowing a 2mm margin of error on each dimension to accommodate for manufacturing variations and ensure compatibility with standard cases.

Small bracket to hold the power supply of a TP-Link SG108PE 8-port POE Switch. ... Please check dimensions before printing as your PSU might have a different size! ... Original .sldprt also attached.

I chose the back because I already have the spool holders mounted on the top back, the space below was already dead space and PSU on the side would only increase the footprint. Here a like to my spool holder setup:...

To make these holders work, you'll need: 4 x screws (for M4x6mm) - Head diameter: no more than 8mm - Length: depends on the specific PSU screw hole dimensions - Size: matches the PSU screw hole specifications Now that I have this setup, it's much...

This is a case for remotely turning on/off the PSU using the Octo Printer, making it easy to manage your printer's power supply. A separate FET Module installation space allows for precise control of the BED Heater, ensuring consistent and reliable...

Choose between with or without countersunk (Ø4.2mm) screwholes and print two of them. ...Mine is printed in PETG 20% infill and are working perfect. Guess you can also use these for horizontal mounting under a table or something else.

I remembered how the Ender 3's power supply unit is mounted on the right back side of the printer, so what I did was design a very simple jig that would allow me to transfer the same mounting holes to the CR10 mini. That way, I could achieve the same...

I designed a custom mount that seamlessly integrates with the existing base, allowing for easy access and removal of the power supply without any modifications needed. ...This STL file represents the complete design, and I will release individual files...

<p>Choose between with or without countersunk (Ø4.2mm) screwholes and print two of them.</p> <p>Mine is printed in PETG 20% infill and are working perfect. ...Guess you can also use these for horizontal mounting under a table or something else.

This design is in three parts - a big bottom mount and an upper mount that are both required, while the third one acts as a bumper. Since there aren't fixed holes on any other side of the frame, the power supply would vibrate due to printer...

While building an enclosure for my Ender 3 Pro, I needed a secure way of mounting my power supply to the underside of the cabinet. This was my solution. ...It secures the back and middle of the power supply, with enough clearance for the factory...

... printing with countersunk Ø4.2mm screw holes or without, and create two units. ...My own prints in PETG with 20% infill are functioning flawlessly. I believe these could also serve well for mounting horizontally beneath a table or other applications.

This is a low-profile clamp/bracket used to mount an Ikea LEDBERG 12-volt power suppply to the underside of a cabinet with one screw. A regular #8 or drywall screw can be used. For best results, I chose to print this thing with the slanted face on...