psu brace 3d models

The Zaribo PSU Brace is designed for use with Zaribo printers that are housed within an enclosure, while the power supply unit resides outside. Its purpose is twofold: it not only provides additional structural support to the frame but also enhances...

It's a versatile ATX power supply unit bracket. ...This handy device has multiple uses, particularly with right-angled edges. Position the bracket atop the PSU's topmost corner and secure it firmly in place using a sturdy long screw.

Just an other Prusa MK3 PSU-Bracket / Brace. My Frame has a Skew-Value of 0.01 ! (Support Menue)</p> <p>Please have a look on my other Prusa MK3 Prints <a...

... to a different spot. ...Most of them are thermal reasons inside an enclosure or maybe esthetic ones. The space freed up by the PSU can be filled with this nice brace which also guarantees frame rigidity.Print in PETG as usual for Prusa printed parts.

Here is another Prusa MK3 PSU-Bracket / Brace. Please take a look here https://www.thingiverse.com/thing:3898665. It fits between Mainframe and Rearplate, clicks into place top and sidewise in the 3030 Extrusion to make it more rigid. You can...

Looking for a bracket to replace the power supply, I came across a nice hughs project “Prusa Bear PSU Replacement Brace”  However, I wanted to give it some shine :) So I redrawn it in Fusion360, replacing the rounding with chamfers and adding colored...

I made this attachment for KalleKnall's gorgeus PSU brace out of my recently published terminal block. It allows you to extend the PSU cable of your MK3(s+) by means of a steady screwing terminal with no need to take apart the entire cable...

If you remove the PSU from your MK3 (for example to place it outside of an enclosure), you can use this brace to maintain the frame stiffness. This was tested with the older silver PSU mount Print instructionsPrints without supports

BUT as my psu was mounted on one of the legs, I printed 3 of the original design and designed my own, slightly based on the original, to fit around the psu. It only screws onto the leg on one side, but it's better then nothing. My enclosure is...

BUT as my psu was mounted on one of the legs, I printed 3 of the original design and designed my own, slightly based on the original, to fit around the psu. It only screws onto the leg on one side, but it's better then nothing. My enclosure is much...

I likes the "original" Ikea Lack table leg brace to make the Ikea Lack enclosure for my Prusa mk3s+ more rigid and prevent it from wobbling. BUT as my psu was mounted on one of the legs, I printed 3 of the original design and designed my own,...

After placing my Prusa i3 Mk3S Bear Upgrade in an enclosure I realised it would be better to remove the power supply unit (PSU) and place it outside the enclosure to improve cooling.I searched for a replacement brace but the Bear Upgrade uses a 2040...

After placing my Prusa i3 Mk3S Bear Upgrade in an enclosure I realised it would be better to remove the power supply unit (PSU) and place it outside the enclosure to improve cooling.I searched for a replacement brace but the Bear Upgrade uses a 2040...

<p>I changed it a little. ...Added the hexagons for looks and a small chamfer around the model.&nbsp;&nbsp;Printed the brace with 30% infill.G-code is with standard Prusament 0.20 profile for PETG.

Prusa offers a brace model that is meant to stiffen up the frame when you remove the PSU. I didn't like this design very much, as it only uses the mounting points of the original PSU, so I made my own. I happen to be experimenting with topology...

Prusa supplies a brace model that is supposed to stiffen up the frame when you remove the PSU. I did not like that design very much, as it only uses the mounting points of the original PSU, and so I made my own. I happen to be playing around with...

Infused with dynamic flexibility

For this, it's advisable to locate the PSU outside the heated chamber and replace it with a replacement brace to maintain the frame's stiffness. There are several options already available, but I wanted to design my own version that uses less...

For this it is advised to put the PSU outside the heated chamber and replace it with a replacement brace to keep the frame stiff. There are a few options out there already but I wanted to design my own version that uses less plastic to print, keeps...

A reinforcement bracket designed specifically for the Mk3's frame, allowing you to relocate the PSU outside of the enclosure if desired. The design prioritizes stability in all directions, while minimizing filament usage and incorporating a sleek...

This is a remix from "PSU Replacing Frame Brace for Prusa i3 MK3" at https://www.thingiverse.com/thing:2859884 for Original Prusa mk2s/2.5 V1 This brace serves as a useful replacement for the PSU, allowing you to remove it from the printer if needed....

A stiff brace replacement for black PSU of Prusa i3 mk3s. No additional fasteners but 2 hooks connects the brace to the top side of extrusion. It can be used together with my Squash ball feet for Prusa i3 mk3s...

A stiff brace replacement for black PSU of Prusa i3 mk3s. No additional fasteners but 2 hooks connects the brace to the top side of extrusion. It can be used together with my Squash ball feet for Prusa i3 mk3s...

In case you remove the PSU from your Prusa MK2(S)/MK2.5 (for instance, if you place it outside an enclosure) and you have a Bear Half Upgrade, this brace will boost the frame's stiffness, preventing z-axis wobbling. In addition to the printed part,...

In case you removed the PSU from your Prusa MK2(S)/MK2.5 (for example if you place it outside of an enclosure) and you have a Bear Half Upgrade, this brace will enhance the stiffness of the frame, preventing wobbling of the z-axis. In addition to the...

In case you removed the PSU from your Prusa MK2(S)/MK2.5 (for example if you place it outside of an enclosure) and you have a Bear Half Upgrade, this brace will enhance the stiffness of the frame, preventing wobbling of the z-axis. In addition to the...

The standard brace is made of circuit board material and allows for air leakage around the fan, it also lacks any support on the other end of the long heat sinks. I suggest putting some tape along the top of the two heat sinks too, to seal it up...

The standard brace is made of circuit board material and allows for air leakage around the fan, it also lacks any support on the other end of the long heat sinks. I suggest putting some tape along the top of the two heat sinks too, to seal it up and...

This mount leaves PSU unit with small gap apart from printer frame, it will be probably not so perfectly horizontal/vertical positioned in general but holds well. Print instructionsPLA worked fine for me, 0.2 layer, no support, no raft/brim. You...

... removed for operation in a heated enclosure. Einsy brace uses 4 M3 screws while the PSU brace uses 2 M3 and 2 M4 screws. ... Links to F360 design files can be found in the original blog post at https://0x7d.com/2020/3d-printer-heated-enclosure/.