ps4 phone mount 3d models

Simple holder for a DS4 controller, compatible with command strips to easily mount or remove.

wall mount for the ds4 with back buttons attached, headset wire gap included

A customizable Bicycle phone mount. Default settings are for MI9T. Need to print 1 case and 2 handle bar mounts. ...The handlebar mounts are glued to the case

Wanted a secondary phone mount for my Schwinn IC4 so that I can connect the IC4 to my phone for power output while watching workout videos on another device. Couldn't find one that already exists so I remixed an STL in Fusion 360 to mount the phone...

A very adaptive phone mount for various smartphones. ...Comes with a duct tape base, but can also be used with [Ball joint phone mount](https://www.thingiverse.com/thing:1035943). ...

I just designed a phone mount base plate to install any phone mount in my KIA XCeed. The base plate is installed between the console and the heater. ... The plate is printed with PLA

This was a fix for commonly found budget phone mounts where phones can be removed from the base mount. The retaining tab failed, this replaces it. ... May require support.

This is modification of the well known dash tray separater design modified to mount a generic ball joint phone holder. ... The ball diameter fits generic or phone specific mounts (not included) with a 17mm ball joint.

bike handlebar phone mount with quick release gopro attack remix of https://www.thingiverse.com/thing:4717208

My Ford has a cubbyhole in the dash. ...I created a phone mount that fits in this hole.

Its a wall mount for moto g power. ...Should fit any phone that is under 7.4in.

Wall mount phone holder with a wooden pattern.Used filament: SUNLU PLA WOOD - low temp.

Daniel Kim's phone mount was transformed by me to seamlessly integrate with every single one of my GoPro accessories.

Featuring a 3D printable design, this bike stem phone mount is specifically created for use with the HTC Desire 510.

I upgraded Daniel Kim's phone mount to seamlessly integrate with every single one of my GoPro accessories.

Simple Wall Mounted Holster For you phone that lets you plug it in while it is in the holder

Phone mount Pajero 2012 Prinetd with ABS nozzle temp - 240C Bed temp - 110C Ambient temp - 38-42C By Talor.K

A custom mount secures a Cisco phone on a wall, created specifically for use at my educational institution.

Designs four and five feature mounts for rubber bands, enhancing stability and flexibility. A .skp file is included for anyone who wishes to make modifications or adjustments. ...Pictures of the completed project will be posted once it reaches...

A remake of Chattel's innovative Playstation 4 controller wall mount is underway, designed specifically to incorporate a convenient space for storing an earphone jack within the controller itself. This modification aims to address a common issue...

The "Mount Phone Clamp" from "Modular Mounting System" by HeyVye is a little small, if you have insert you phone in a booklet phone case. So I enlarged the clamps a little bit. ...They are still compatible with the rest of the "Modular Mounting System".

This is a mount for using a phone on a manfrotto tripod, originally meant for a camera. The mount is adjustable and is able to accommodate phones of different width. Rubber bands do need to be used to keep the phone from slipping out of the mount.

Simple and easy to print in place phone mount. The two gopro mounts allow it to mount it horizontal or vertical. I like to use the small tripod from gopro. Just use a rubber band like shown in the pictures to keep the phone in place. Made for...

This is a simple mount for the phone holder for the MotoCaddy, slide it in and use a RAM mount or similar to hold the phone.This is just the mount, not the other arms and phone holder peaces. NOTE: Apparently not a snug fit on the 2022 model, from...

This is a simple mount for the phone holder for the MotoCaddy, slide it in and use a RAM mount or similar to hold the phone.This is just the mount, not the other arms and phone holder peaces. NOTE: Apparently not a snug fit on the 2022 model, from...

I designed this mount to replace the Bontrager Insta Mount that holds the cell phone to the bike with double faced tape because it fell off more than once and I did not like the extra mount permanently attached to my phone case. With this mount; I...

I pulled this from https://pinshape.com/items/54250-3d-printed-controller-mount-switchxboxps4-no-supportsone-piece credit: the3dcoder Other Wall Mounts pictured... ... Joycon: https://www.thingiverse.com/thing:3465818 DualShock3 SIXAXIS (oldschool):...

New photos to match the new v2 model.Remix of the wall mount from https://www.thingiverse.com/thing:3158960 and V1/V2 use the Skadis pegs from https://www.thingiverse.com/thing:5243936 Printed with 15% infill, 0.28mm layer height and with supports on...

I like the original design but I prefer a single controller mount that I put two horizontally. I have also moved it up and make the cable hole bigger. The one I printed with silk PLA was broken so I thicken the area near the cable hole with fillet. ...

Remixed to add a larger mount area so tape, glue or more screws can be used. Also rotated it so it can should be easier to print without supports. ... The joystick holders can be a little weak, they snapped off pretty easily at 20% infill, so I...