ps3 vertical stand 3d models

It will charge horizontally and vertically. Gap between the arms is 82mm or 3 1/8" Printed at 0.4 res in PETG on Ender 3 Pro with 30% fill and with supports. ...It's a little tricky to get the supports out because of the horizontal arms, but if...

A portable storage stand for the WD Elements 2.5" disk, designed to hold it upright or on its side. Other disks with similar dimensions - approximately 18mm thick at their edges and 21mm in the middle - should also fit, allowing you to scale the...

I couldn't find any stands that fit my fat PS4 perfectly, so I decided to create one myself. You'll need to print two of these stands for your PS4 to function properly. Also, make sure to flip them over in your slicer before printing - the base down...

I thought the laptop stand by @Brockerboy (https://www.thingiverse.com/thing:4237708) was so kickass and it really needed to be made suitable for all laptops so I just made one small alteration, width. Now you can get it in eleven sizes: 20-30mm ...

It's possible that this stand may fit older fourth-generation devices as well, given their similar dimensions. However, please note that the design ensures a snug fit for the HDHomeRun device, which can be especially noticeable during initial...

Since I'm one of the few who use their PS4 on its head, I've got a request to modify the PlayStation stand so it can be used with the Blu-ray on top. So here it is! For more information or if you also use your PlayStation upside down like me, follow...

Tested with MacBook Pro (16-inch, 2021, M1)Differences from v1: Added arch for extra stability, larger vents.Disclaimer #1: The stand will obstruct ventilation somewhat. I tried to add a gap to help with ventilation. Use at your own...

Next, I constructed a stand that would provide clearance for the bearings to attach securely while allowing room for smooth rotation. To ensure precise fitment, I designed and printed the stand with exactly the same diameter as the bearings. Knowing...

I have simple but helpful solution for you - The Vertical Device Holder. The original project is: 10cm wide 10cm long 7cm tall which makes it printable on many smaller printers. Slots: 2x Laptop slot - 2cm wide 1x Tablet/phone slot - 1cm wide...

Remix of @formulagp46 MacBook Pro 2020 Dock to accommodate two MacBook Pros in vertical orientation.  I've checked this with both Intel and M1 13" MacBook Pro 2020 and with my wife's Intel 15" MacBook Pro and they all fit nicely.  Will...

I use to have everything all over my desktop, so I decided to design this to have things in vertical position to have more room. I designed it first for my kindle oasis, but later I found out that it works well for the iPad with the case and maybe...

This item allows the Formd T1 V2.0 to be oriented vertically. It adds an additional 60mm of height to the case which is just enough to avoid using right angle power/display cables. It is securely attached to the back of the case using 4 M3 screws. ...

... some rubber pads, both to avoid scratching the computer and to prevent it from slipping. ...I used the rubbers that are used for chair feet.You can place the PC both vertically and horizontally.It is very stable, resistant, easy and quick to print.

It is absolutely necessary to carefully position your stand in one location and firmly adhere it to that surface using Command Adhesive strips placed between the bottom of the stand and the topmost surface. As per my observation, even if properly...

This is a remix of Lukki15's “Adjustable Dual Laptop Stand” and while I loved the original design, I remixed to save on desk space and hardware.  I've printed three of these for different laptops and it worked perfectly for...

UPDATE 17/12/2018 A new component has been added to the design: a Clamp for rod stand, perfect for use in chemical labs. ...This enhancement includes a main body, two caps that seal the housing of the nuts, and two small wings knobs to secure M5 hex...

Hey guys, check out this design for a Razer Blade laptop stand that can be easily adapted to any laptop with the same dimensions. I wanted to create a setup where the lid can remain open to maximize airflow and extend the lifespan of the screen. The...

I didn't see any stands that I liked for the fat Ps4 so I made this one. Obviously you will need to print 2 of them for your Ps4. Also you will need to flip it over in your slicer. It prints best with the base down. I didn't need any supports to...

I needed to mount very small PCBs standing up, instead of using the screw holes. This mini-mount was glued onto the case surface. The PCB slides into the mount. More than one mount can be used for larger boards. The STL can be skewed...

Added size indicators on the parts for convenience. Here is a low-profile stand that uses up less space to display your lightsabers. ...It has different heights and braces to fit most hilts. For Yoda, scale the parts to 75% of the original size. No...

Designed as a way to keep my laptop 'dock' (really just a glorified USB hub) in a tidy, vertical position alongside the laptop itself. Allows for decent airflow, access to some data ports and the power button, and most importantly saves a *lot* of...

 I could have also reduced the front toe opening but that would have restricted which laptops could use the stand.Quick note, if these look "thinner" than the others it's not you.  Exact same dimensions of the previous prints but only 1/2...

Simple phone stand for a Samsung Galaxy S20FE in a bulky case (such as an Otterbox) that supports wireless charging.  The “ears” help keep the phone in the optimal charge position (too many times I found out my phone was ever so slightly too far...

I drew inspiration from Quad_out's Flip 3 stand concept to create my own design, which required a directional approach. I separated the design into two parts: the bottom section was straightforward and functional, while the top portion allowed for...

Keyboard stand for Logitech G915/815 and TKL versions (and basically any other that has the same dimensions on the lower part).Needed some extra space when using my tablet.Might be a good idea to glue some rubber feet under the holder for some...

Also the edge of the side has a raised bead, so I added an extra "step" to the stands to hold it away from the side to clear the bead (and the outer edge of the cone shape). I moved the user variables out of the common files so you can make a file...

UPDATE: To maximize storage space, I created a stand for the pill box to prevent it from rolling or falling over when placed on its edge. This holder can accommodate a perspex lid that is slightly larger in diameter than the box itself, measuring...

Printed on Geeetech A20M ----------------------------------------------------------------------------------•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Display for PS3 pad. ...I suggest to print it "stand" Printed...

... enjoy this new Series S Stand. ...This new model gives you the ability to integrate your own touch to this stand by creating your own side logos and adding it to your stand. ...The logo pocket is 21.76 mm in diameter and the pocket depth is 0.75 mm

And this a major reason I made this stand to fit like a glove rather than simply have a large enough opening. This way the notebook sits snuggly and securely and there is little chance of it tipping towards the shorter side. *Note the stand in the...