ps3 slim case replacement 3d models

This sleek accessory holds a single slim cigarette. Its slender shape was carefully crafted to cradle the delicate filter. ...A beautiful, hand-engraved rose blooms at its center, exuding elegance.

For Xbox 360 Slim and Xbox 360 E. -all screw holes had 1 centimeter diameter counterbore, should support most generic PC HDD screws -holes for a pull tab, use scotch tape. ... -thick pry hole for when the pull tab was unusable/broken, use a flat...

I designed this enclosure to resemble my previous design found at Thingiverse under the identifier 1905252, however, I slimmed it down slightly and expanded the display window so users can clearly see their insulin levels. ...These enclosures were...

For Xbox 360 Slim and Xbox 360 E. -all screw holes had 1 centimeter diameter counterbore, should support most generic PC HDD screws-holes for a pull tab, use scotch tape. ...-thick pry hole for when the pull tab was unusable/broken, use a flat head...

I'm slowly learning Blender, I made this very basic slim 2 disc holder for minidiscs. I plan to do a 4 disc holder that folds, I'm still working out how to do the hinge as print in place. ... On my Ender 3 it printed in under 2 hours at maximum quality...

Its a simple case and its great for non heavy tasks

Compact cases fit snugly around the spacious Anet A8 mosfets, readily available on numerous online platforms.

0.3mm layer heightNo supports instructions:glue it with superglue at your phone case

To make the most of your custom case, follow these simple steps: Use the Options Below to Create Your Perfect Fit: Set Pattern Radius to 8 Select a Build Plate to Get Started Make Your Case 1.8 Times Thicker Keep Patterns Close Together with Overlap...

To Bring My Thin iPhone Case to Life, I Used PLA Filament Due to Its Superior Durability Compared to ABS. Printing with 0.2 MM Precision and Applying 10-20% Filling along with One Shell Provides a High-Quality Finish. Here's How You Can Make This...

I recalibrated the original casing to ensure a perfect fit on my printer. ...The cap now sits snugly in place, thanks to an added clip that makes all the difference.

This sleek and versatile case is specifically designed for the VESC 4.12, ideal for thorough bench testing. ...To install it securely, use four 16mm M3 screws, ideally with a countersinking feature to ensure a seamless fit.

the lid locks with the case by an M3 screw at least 24 mm and 4x 5 mm wide and 2 mm depth magnets but honestly they are an overkill just the M3 screw gives enough resistance to close it shut. also 2x 40mm fans on the lid but again overkill.. i...

The Raspberry Pi 4's impressive capabilities are neatly showcased within a sturdy and durable casing, ensuring that your device remains protected from the rigors of daily use while still exuding an air of sophistication and style. ...Whether you're an...

http://www.thingiverse.com/apps/customizer/run?thing_id=281157 Instructions Using the Following Options: Font = knewave.dxf 4swidth = 6.17 5length = 123.8 5cornerR = 8 5width = 58.6 word1 = 4width = 58.55 pattern_shape = 6 iphone_version = 4 5height...

http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: case_taper = 3 4sthick = .6 5sthick = 1.0 index_j = 0 index_i = 1 5length = 123.8 type_of_case = 3 6Plussthick = 1.5 4_height_tolerance = .2...

I designed this case primarily for entertainment purposes, acknowledging that it provides limited protection against damage. Print with PLA material. ABS will shatter and break due to its inherent brittleness. The print settings used were 0.2 mm...

The footprint of this case is very small, not much larger than the two batteries side by side, and the lid holds firmly closed with the magnets in place. The hinge is probably the weakest part of the design, though having little room to work with I...

Print as-is, no supports needed. THis model can be scaled up-or-down to suit your particular size needs. If you're looking for a case that's a bit easier to open (but larger) see...

--------------------------------------------------------------------------------------------------------------------------- My second version of a case for the Iphone X / XS. This is now thinner again and consists of 2 parts that are put into each...

Remix of 2.5 inch hdd case that'll also fit an SATA USB connector.

... ...To print this custom design, set the options as follows: pattern radius - 4, iPhone version - 2, build plate selector - 2, pattern overlap - 100%, pattern shape - 3, pattern thickness - 30, case thickness - 1.8, and pattern rotation - 0.

Remix of this cool 5 cigarettes case but just for 2. All the credits for the original author. ... Sliced with SuperSlicer and printed in my heavily modified Ender 5 with Klipper firmware on SKR mini E3 V2, BMG DDE, Dual z-axis, BLTouch, and Octoprint...

Instructions Using these Options: pattern_rotation set to 90 Degrees pattern_thickness at 5mm iPhone Model Version is 1 Pattern Overlap set to 64 pixels Build Plate Selected as Default Case Thickness at 2.4 inches Pattern Radius at 14mm Pattern...

... ...Please follow these guidelines when customizing your object: pattern_overlap = 3, build_plate_selector = 0, pattern_thickness = 4, pattern_rotation = 0, iphone_version = 2, pattern_radius = 8, case_thickness = 1.8, and pattern_shape = 6.

... Iphone Enthusiasts Like Me. Using These Awesome Settings: Pattern Thickness = 6, Pattern Radius = 9, Case Thickness = 1.8, Pattern Shape = 6, Iphone Version = 2, Build Plate Selector = 0, And The Best Part - A Cool Pattern Rotation Of 52 Degrees!

Instructions Using the following settings: * pattern_rotation: 0 * pattern_radius: 8mm (eight millimeters) * iphone_version: iPhone version 2 selected * pattern_overlap: twenty-five percent overlap * pattern_thickness: six millimeters *...

I added some knurling to the lid and base, as well as a loop to the lid so the case can be attached to a keyring and taken on the go. Knurling used from Wilko's design, "Knob with knurling," on Printables.

I wanted to put my Retropie Pi zero W into a case, but I wanted to make it more visible as it is my Retropie Emulator. I added the Retropie logo. ... for putting it together use 4x M2.5 5mm screws

http://www.thingiverse.com/apps/customizer/run?thing_id=40703 Instructions Using the following options: pattern_overlap = 0 case_thickness = 1.8 pattern_thickness = 4 build_plate_selector = 0 pattern_radius = 8 pattern_rotation = 0 iphone_version = 2...