ps3 controller pieces 3d models

Voxel PS3 Logo created in the MagicaVoxel editor.

3D Printable Case For FRC PS3 Eye Vision Processing Module

This was originally designed to install a filter using a floppy disk on my PS3 Eye for a DIY trackir. I used it for a while with good results, but finally decided to open the camera to remove the IR filter anyway, so I finally installed the filter...

I had purchased a dirt-cheap used Fat (original) PS3 that functioned properly, but it lacked its hard drive tray and hard drive - I was looking to upgrade the hard drive anyway, so I crafted a custom tray based on a laptop drive that snugly...

This was originally designed to install a filter using a floppy disk on my PS3 Eye for a DIY trackir. I used it for a while with good results, but finally decided to open the camera to remove the IR filter anyway, so I finally installed the filter...

Support Arm for PS3/PS4 Joystick, arm remanufactured to place it closer to the wall.

Holder to mount PS3 Eye on the CR10s. ... Holder is mounted without screws

AI3M PS3 eye camera mount long (RIGHT ARM anycubic I3 Mega)

Another Customized PS3 Eye Mount for the Tronxy X5S 3D Printer

Simple PS3-Eye mount for my Philips Momentum 436M6 (42,5") monitor. ...

I bought my PS3 super slim basic model without any HDD second hand few years back and had the SSD wedged in with a piece of cardboard until I finally decided to print an actual tray for it. ... If someone still needs this tray today, hope your print...

By removing the top metal case of the power supply at the point where the grid piece fits, air flow is significantly facilitated, keeping the power supply cool over extended periods of time - a marked improvement from its earlier tendency to overheat...

You can easily create custom analog sticks for your GAMEware Gamepad on PS3 by replacing existing ones or adding new ones with personalized colors. The design allows for a seamless swap, whether you're looking to replace a broken one or simply want a...

This mount is perfect for a PS3 Eye camera on a Ender 5. ...Just print it without support.

Contributed a basic wall mount for the PS3 Eye Camera mount used with Duplicator I3 Print Bed designed by ChristianCooper.

A External Power Supply case for for Fat PS3, to reduce heat build up inside ps3 and make more space for extra cooling inside ps3, case has right measurements for power supply to fit right in with no problem and it comes with 2 small 40 fan's at...

This was originally designed to install a filter using a floppy disk on my PS3 Eye for a DIY trackir. I used it for a while with good results, but finally decided to open the camera to remove the IR filter anyway, so I finally installed the filter...

This clip mounts a PS3 camera to the stock spool holder of a Ender 3 printer. ... The camera is held by friction

Here are some specific print settings that have worked well for me: * Ender 3 PRO PS3-EyeCam-Halterung 4 V1.5 (my favorite) * Ender 3 PRO PS3-EyeCam-Halterung 1 V1.1 * Ender 3 PRO PS3-EyeCam-Halterung 2 V1.1 * Ender 3 PRO PS3-EyeCam-Halterung 3 V1.1...

... the rear frame brace adjacent to the Y motor, effectively mounting the PS3 Eye Camera in place. ...This configuration utilizes the Arm and Cam Holder file from ChristianCooper's PS3 Eye Camera mount specifically designed for the Dupicator I3 Print Bed.

This remix adapts the Sidewinder PS3 Eye Cam mount designed by DustinGr, tailored specifically for the Artillery Genius. Notably, the attachment screw's position varies between models. ... Additionally, key modifications were made to the arm's...

... this mount with my Pi camera but when it died and I replaced it with my old PS3 camera I wanted to reuse most of my current mount. I have designed a camera mount that the PS3 camera fits snugly into that connects to the arm of the original design.

You can use the screws from the disassembled PS3-eye for mounting the PS3-eye PCB to the base Additionally you will need: 2x M3 bolt 20mm (tapered) 2x M3 nut 1x M3 bolt 35mm 1x M3 nut (locking) 1x Lens mount 1x Whichever lens Instructions Print out...

This mount is specifically designed to be an ideal fit for a PS3 Eye camera when paired with an Ender 5. ...Printing it without any support structures will yield the best results.

I have a backward compatible PS3 fat, but wanted it with the slim version logo! ... By purchasing it, you can obviously get further versions without additional fee in case I modify my file.

Things that print with support and with brim: Ender 3 PRO PS3-EyeCam-Halterung 4 V1.5 (my favourite) Ender 3 PRO PS3-EyeCam-Halterung 1 V1.1 Ender 3 PRO PS3-EyeCam-Halterung 2 V1.1 Ender 3 PRO PS3-EyeCam-Halterung 3 V1.1 Things that print without...

Here is some useful information about the power supply: http://www.psdevwiki.com/ps3/Power_Supply My to-do list includes: * Lid (already completed) * Secondary support (I had to modify the design, so I'll be changing it soon) * Power button support *...

Its designed to have Space on each Y-Axis position (see Picture in Y+) My Settings: PETG Prusament 0,2mm Layer height 20% Infill Hei Leute, Hab diese Kamerahalterung gemacht für das Ps3-Eye an einen Mk3s. Mit der Gabel über den Bettrahmen und...

Pro-Gamer's Essential Accessory - The Fighter's Console Companion Board The Pro-Gamer's must-have accessory is finally here - the Fightboard PCB holder, specifically designed for PS3 and PS4 consoles. ...This sleek, high-quality holder keeps your...

You can find my PS3 cam holder which Octopi uses to monitor my Creality Ender 2, conveniently located right here. The holder is designed specifically for attaching to the Z-axes cap where the X-stop is also secured. ...If you're not an Ender 2 user,...