ps2 hard drive caddy 3d models
114893 3d models found related to ps2 hard drive caddy.
thingiverse
Recently bought a used Quantaplex T41S-2U server system without drive caddies. ... Original drive caddies went for 25€/piece, which was just too expensive, so I designed and 3D printed my own...
thingiverse
... ...Missing screws forced me to secure the Drive in the Caddy using strong doublesided Tape. The Caddy now fits neatly into the Bay without any tools, just like the original one. ...This makeshift solution may also work with other Dell SFF Desktops.
thingiverse
... However, I encountered an issue - the bottom and side bolt holes on one of my drives didn't match the pre-installed caddies that came with the case. ...To resolve this problem, I created a new set of custom-designed caddies using Tinkercad.
prusaprinters
... squeeze to unlock. I shucked a drive and the bottom and side bolt holes on the drive didn't match the caddies that came with the case so I designed a new one. This caddy isn't quite perfect, but better than just enough. ...Designed in Tinkercad.</p>
thingiverse
Quick and dirty, no-frills DIY enthusiasts can build a sturdy hard drive rack for up to five 3.5-inch or 2.5-inch hard drives using just two sets of four printed rails. ...Simply screw in your drives, and you'll have a compact 200 mm long storage...
thingiverse
You need to cut off part of the PS4's shielding limiting the hard drive's height, as well as the top of the original drive caddy. Don't worry, the HDD support will hold your drive safely in place even though your caddy's top has been chopped off. ... ...
thingiverse
This is a caddy to mount an HDD in replace of a CD Rom drive. You are able to reuse the bolts from the HDD to mount the caddy and also comes with clips to hold the HDD in place. ...These clips are optional as the HDD sits quite snuggly.
thingiverse
Tried Sacy's model for a Cisco UCS C220 M3 drive caddy but found two parts were not letting the drive fully slide in. Modified the design to remove the small bits in the back left and right that were in the way. ...Updated model now seats properly in...
thingiverse
Remix of Sacy's C220 M3 drive caddy. Cut 2mm off the entire length of the right side so it would fit into the drive bay of a Cisco UCS C220 M5 1U server. ...Also, cut a notch out of the back left side to make clear the protrusion in the drive bay.
thingiverse
When we scored a couple of Dl380 G8s at a bargain price, I quickly discovered that there was no toolless version for the caddy available.\r\nI even adjusted the only existing one previously made, but it resulted in a caddy with a subpar handle.\r\nSo...
thingiverse
I 3d Scanned the 2.5-inch drive blank to get the locking part, cleaned it up, and remixed https://www.thingiverse.com/thing:4866109 for the SDD drive caddy. Merged them together and got this as the final product. ...It slides right in to the bay and...
thingiverse
The costly and rare drive caddies demand a work-in-progress approach as no original model is available for reference. Current focus is on ensuring proper fit, while considering the best way to incorporate ribs as supports. ...Compatibility with both...
thingiverse
Customized version of https://www.thingiverse.com/thing:5688085 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5688085
thingiverse
Customized version of https://www.thingiverse.com/thing:5688085 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5688085
thingiverse
Customized version of https://www.thingiverse.com/thing:5688085 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5688085
thingiverse
Customized version of https://www.thingiverse.com/thing:5688085 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5688085
thingiverse
Customized version of https://www.thingiverse.com/thing:5688085 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5688085
thingiverse
To address the issue of limited drive caddies, I opted to create one myself using a combination of CAD software and industry standards. The solution consists of a simple yet effective design that allows for easy installation and removal of drives...
thingiverse
Remix from: https://www.thingiverse.com/thing:4371177 Edited to fit one SSD and one 2.5" laptop hard drive (height 9.5 mm) at the bottom.
thingiverse
Building a water cooling system in my new Enthoo Evolv tempered glass case has led to an unexpected challenge: using only two hard drive spots in the basement due to space constraints from my pump and reservoir. To add a third hard drive, I looked...
thingiverse
Simple 3" Floppy Disk Drive Caddy. Please note this is for the 3" drive widely used in early Amstrad built machines (CPC, PCW, Spectrum +3) not 3.5" drives. I've replaced a few of my 3" drives with Goteks and wanted to use them with a Greasweazle...
prusaprinters
Simple 3" Floppy Disk Drive Caddy. Please note this is for the 3" drive widely used in early Amstrad built machines (CPC, PCW, Spectrum +3) not 3.5" drives.I've replaced a few of my 3" drives with Goteks and wanted to use them with a Greasweazle USB...
thingiverse
https://www.thingiverse.com/thing:3444137 Had a drive caddy which I'd printed a few times, but it always failed on the fins and the nubs on the side of the drive seemed too wide for the servers, So I removed the nubs, and Fixed the overhang on the...
thingiverse
just a hard drive holder for a ps4 fat for the Seagate 2tb hard drive
thingiverse
------------------------------------------- 2.5" HDD cases used: https://www.banggood.com/ORICO-2139U3-CR-2_5-inch-Type-C-Hard-Drive-Enclosure-p-1109914.html...
prusaprinters
... per drive. ...The center supports are optional but do help with stability. These were made specifically with the Seagate Backup+ Hub 8tb drives they sell at Costco all the time. ...They print support free in the orientation you see in the renderings.