prusaslicer filament profiles 3d models

Since there is more space here than in a K40 laser cutter, I have optimized the middle frame base for attachment to aluminum profiles. With the new middle section, it is possible to adjust the height if both brackets are already attached to the tube....

Remix of Orange Pi Zero case from “Farrukh Pitafi” (https://www.printables.com/it/model/233087-orange-pi-zero-case)I added a clip on the bottom case to allow the case to be attached to aluminum profiles (30x30).First time it's hard to remove, but...

The customization options include an additional tooth depth of 0, a profile of 6, a motor shaft diameter of 13.2mm, no retainer, an M3 nut depth of 2.7mm, an idler height of 1.5mm, an M3 nut flat dimension of 5.7mm, an M3 nut diameter of 3.2mm, an M3...

https://thingiverse.com/apps/customizer/run?thing_id=16627 Using Options Motor Shaft Length Set to 6.1 IDLER Set to 5 Additional Tooth Depth Set to 2 mm M3 Diameter Set to 3.2 Pulley Top Height Set to 13 Nut Angle Set to 180 degrees Distance of Nut...

This text presents MakerWare profiles for Polycarbonate (PC) printing on a Replicator 2x. PC has similarities with T-glase, being crystal clear but twice as strong and tough as ABS while stiffer than nylon. Suitable for mechanical use up to 150°C,...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions: Using the following options: idler = None motor_shaft_diameter = 6.1 mm additional_tooth_depth = Zero millimeters main_pin_diameter = 3.2 mm pulley_thick_height = 12 mm...

Thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the Following Options: Motor Shaft Length: 5.2 Mm No Idler Tooth Depth Added: None M3 Diameter: 3.2 Mm Nut Angle: 90 Degrees Distance to Nut: 1.2 Mm Top Pulley Height: 12 Mm...

This is my design of a buck converter case for 2020 extrusion profiles that I use for my 3D printer. The buck converter can have a maximum dimension of 62x39.5x19mm (that is the inner dimensions of the case). It has a 0.2mm gap between the lid and...

These clips should snap right into place within the x-profiles and be able to slide back slightly. The LED-strip clip was a quick solution on demand, but I haven't yet had time to test its tolerances. The original parts were thoroughly tested and...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following settings: motor_shaft = 5.2 mm teeth = 20 pieces additional_tooth_depth = no depth pulley_b_ht = 8.0 mm pulley_t_ht = 12.0 mm retainer_ht = 1.5 mm...

Both low and high profiles now - pick one. Works well on NA, NB. may work okay on NC (I don't have one to test and have heard mixed feedback). Will NOT work on an ND but I have a ND version elsewhere on this site. Just slips into the open...

:-) I use the holder for a DIY laser cutter project and here too the tuning works great. Since there is more space here than in a K40 laser cutter, I have optimized the middle frame base for attachment to aluminum profiles. With the new middle...

I Designed a Unique Filament Clip Using Fusion 360 to Fit Specific Reel Profiles, Starting with http://www.thingiverse.com/thing:1098912. It Works Perfectly on These Models: 1) RS 500g reels 2) RS 300g reels 3) UP-ABS 500g reels 4) Verbatim - ABS 1...

A metal extrusion guide that clips onto an aluminum profile

Since there's ample space available, I've optimized the middle frame base for attachment to aluminum profiles. With this new middle section, you can easily adjust the height even after both brackets are attached to the tube. This makes aligning the...

... M3_nut_depth reaches up to 2.7 levels in total length. Profile setting currently selected at number two with full precision guaranteed within parameters set and confirmed by testing procedure results to validate design performance and integrity

-- THIS CASE FITS ONLY SMALL FOOTPRINT M12 MOUNT CAMERA MODULE This is a Raspberry Pi camera enclosure with mounting parts for 2020 aluminum profiles with v-slots. You may not need all of the parts, or print more for an even more flexible...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using The Following Options: m3_dia Is Set To 3.2 m3_nut_depth is Set to 2.7 Retainer Option is Activated at 2 Units motor_shaft Length is Measured as 5.2 mm retainer_ht...

A profile of 6 has been chosen, along with a pulley B height of 8 units. There are 11 teeth on this pulley, and the pulley B diameter is 20 units. The nut shaft distance measures 1.2 units, with a nut angle of 90 degrees. Retainer installation is not...

Instead of 3030 aluminium extrusion that is hard to buy I used 2020 aluminium profile because I had plenty of that after building the Dremel CNC. I decided to build this project to recycle parts from my old JGAurora 605s (my first ever 3D printer!) ...

Additionally, the box features a sliding piece designed for use with 2020/2040 aluminum profiles. I used this box on my Ender 3 printer to control LED lights using a Raspberry Pi, taking advantage of the cable management features and secure storage...

Additionally, there is a sliding piece for accommodating 2020/2040 aluminum profiles on the same side. I mounted this enclosure on my Ender 3 printer to control LED lights using a Raspberry Pi. The hole on the side proved useful for routing cables...

Part 1, 2 and 3 can be found here: - Part 1: DuetWifi Installation and PanelDue Mount (https://www.thingiverse.com/thing:2428995) - Part 2: Mini Differential IR Probe mount for Replicator 2X (https://www.thingiverse.com/thing:2475179) - Part 3:...

Instead of 3030 aluminium extrusion that is hard to buy I used 2020 aluminium profile because I had plenty of that after building the Dremel CNC. I decided to build this project to recycle parts from my old JGAurora 605s (my first ever 3D printer!) ...

I also tweaked some aspects of the original Tech2C compact extruder design: * Reduced space for the filament, making it simpler to insert new filament. * Thicker plate now measures 8mm (originally 5mm) for added stability. * A lever has been added to...

Filament guide for diverting filament. ...For example, around a corner.

Filament bin for the filament bin holder file on thingiverse

Filament Filter for 1.75mm Filament Print Settings Printer: TinyBoy

Yet another filament clip for Devil Design filament spools

Filament guide ==================== Thin filament guide with screw hole