prusa slicer temperature tower 3d models

3 perimeters should be ok, but I recommend putting more walls around the screws using a modifier in the slicer, especially if you plan to skip on washers (seriously, just get some washers).It is highly recommended to pair the MMU with a filament...

Do not use slicer's brim setting as you need the latches where the housing parts connect quite clean. Numbers For ease of printing, I've created the numbers as a single body. I merged them altogether with a thin plane of 0.0001 mm, hence it will not...

If your printer allows you to print the entire deck, then you should do so, then you need to specify in the slicer an increased density of filling for the area bearing an increased load. If you have additional questions, I will answer them in the...

Soap slicer - an essential tool for simple, accurate division of soap bars. Streamline your soap-slicing routine with this easy-to-use cutting machine. Simplify your soap-cutting tasks with a dedicated device that guarantees clean cuts every time....

You will have to orient everything to lie flat in your slicer. The cable chain mount should be printed with the link tabs up top. You will need to print 17 links/closures, and one each of the others. You’ll need internal supports for the slot...

 In this case rescale the rear transmission shaft in the slicer to add 4mm in one direction ( the length).  This V2 uses my new differential and my new 16 to 1 gearbox.  The steering is also direct from the servo but this time the servo is not upside...

(Based on the suggestion from one person of X 11.8 mm x Y 11.8 mm x Z 5.7 mm.) If it is still too small or loose, then upscale in the slicer or shim it with some soft rubber or similar. Important:ensure that it won’t stick when depressed: it must be...

Note on the Arrows: Ive had the best results with a bit of slicer manipulation: I added a modifier to the tip of the arrows such that the tips are printed at 100% density while the shafts are printed at 20%. This will help balance the arrows in...

The use of an SLA printer (StereoLithography Apparatus) is also not ruled out.CURA 4.10.0 was used as Slicer software. The parameters with which the pieces were printed in my case were: low quality profile with layer height of 0.28mm, 10% cubic...

Updated battery tray (Unprinted) Radiator in front doesn't look great from my slicer, need comments on how to improve. maybe just reduce detail. I print at .3.. on this. Added Battery Lid (Unprinted) Not as easy to print as I would like and no mount...

Print this update if your Slicer's filament profile is perfectly tuned.  DescriptionThis model is loosely based on the Bambu Lab X1 Y-Splitter from kjbturok. I was initially planning to remix kjbturok's model but I had to start from scratch...

G-CODE AMMENDMENT: You need to ammend the following G-Code scripts to the very end of the "End G-Code" of your printer settings in CURA (or in an other Slicer): ;OPTIONAL AUTO POWER OFF SCRIPT* M109 R40 ;Wait until hotend temprature is down to 40...

Before starting, set the printer and the resin in the slicer according to the manufacturer's guide values. Informationen, Hilfe und Lösungsansätze zum Siraya-Test: Information, help and solution for Siraya-matrix: ...

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

 See new_button.stl and new_button.step if interested.I flipped “Lid v7.stl” upside down in the slicer before printing so the wider side is on the bedplate. The fitment of the display holder to the lid and the lid to the case are good and didn't need...

Remember that this protractor has 0.1 degree (6 minutes) vernier scale marks to simplify entering values in CAD software!Solution for PrusaSlicer (and maybe some other slicers) to slice the scale correctly.The marks in this protractor have only...

(Please note the support for the Chinese language slicer) Support is only necessary around the bayonet. In PrusaSlicer, this can be done by force support, which can only be set to bayonet. It is good to set the support distance from the z-axis to 0.3...

Don't forget to subscribe to my channel to stay updated on new videos and receive the latest updates.If you liked this thing - let me know by putting like!Parts links below: Artillery SW-X2 3D Printer Promo-Code 50X2ZB (with $50 off) Artillery 3D...

I could not find a miniature three-position switch with six contacts, so I had to tinker (after watching the video, everything will become clear): See the video for details: If you liked this thing - let me know by putting like!Parts links below:...

There are also a number of spring mounting holes added to the rack to adjust the tension depending on the properties of the spring itself and the required coil braking force.See the video for details: See also: If you liked this thing - let me know...

Good luck with your creative endeavors!See the video for details: If you liked this thing - let me know by putting like!Parts links below: Empty LDPE Plastic Dropper Bottle Empty LDPE Plastic Dropper Bottle Black Glue Micro-Tips Cylindrical Pin ...

However, you will see it in action in my videos in the future, but for now, I have a video of its assembly since the mechanism is relatively simple, and there are some nuances that are worth seeing before assembling it.See the video for details: If...

You can fix screws or pins with any of the adhesive options that are presented in the list of links.How I made the previous box can be seen here: If you liked this thing - let me know by putting like!Parts links below: Geeetech Mizar M Dual Extruder...

All my other setting adjustments are based on flow cubes and temp towers.Post Printing:The corner brackets and clamps each require eight inserts. Make sure the inserts are flush with the tops of the corner brackets.The right gantry needs two inserts...

Arastacia took the dagger, and locked it away in the highest tower, never to be seen again.    Lydia, The Apothecary Lydia, an old woman with great skills in herbalism and alchemy. She has tended to the sick and wounded in her village for over 30...

Ideally, the mirror should not be able to rotate in either direction and the 'tower' on *Windshield Adapter* should line up with a visible casting seam in the mirror body. If you glued the *Windshield Adapter* on crooked, you may need to adjust the...

For Cura slicer, i use the Barbarian plug-in to convert the parts to millimeters for printing. This stand will fit many boats besides a DF95 and there are several ways to make sizing adjustments by moving parts around and changing the PVC pipe...

Well, the possibilities of PrusaSlicer (and probably other slicers too) give you the tools to realize this yourself, with a good dose of creativity!Principle.The articulated model is supported at several points with printed springs which in turn are...

However, for the non-threaded parts of your models there is no need to waste time and energy printing that fine (and slow). In the example below the use of variable layer height saves about 9 hours of printing time (which equals about 1.4 kWh of...

So far I've only ever printed PLA, so I can't speak to the thermal performance if you wanted to use this for printing anything needing really hot temperatures, but the internal cooling seems to be excellent, and as long as your heater block is...