prusa printer enclosure v2 3d models

(The original 3mm slotted door hinge pieces are still compatible with the 4mm slot remixes.)This remix contains only the parts from the Prusa Enclosure V2 (MMU2S) that hold the panels. Meaning: if you already own the parts from the V2 enclosure, but...

Enclosure for Geetech Prusa I3 LCD Display module. Did not like it being at the top of the frame, causes the whole assambly to wobble when fiddling with the dial during print. ...Printed in PLA Plus, Resolution 0.1000 extruder temp 213c bed 60c....

* Finally, follow Prusa's Enclosure V2 [guide](https://blog.prusaprinters.org/mmu2s-printer-enclosure_30215/) for how to install the PSU externally --- Below are links to the other parts that I used to complete my enclosure build: [Angled heat bed...

I also made an exploded view drawing to help with assembly.Build can also be found on Thingiverse.Purchase Parts:QTY 12 - 20x6x2mm magnets (used to secure the doors from unwanted sliding and opening)QTY 8 - 6x50mm wood screws (used to mount the...

Merchandise for Prusa Printers

Printer Prusa parrot Print instructionsPrusa maker parrot

I couldn't find one to fit my 3D Printer Enclosure so, I designed one. I printed it with my Prusa MK3S printer using PETG filament. A small support is needed when printing it. ... This enclosure heater uses one 120mm fan and a 300W PTC heater both...

I didn't and then suffered the consequences The 27 SL1S enclosure front bottom vent.stl is not probably needed at all but I had it designed so I printed it Push 26 SL1S enclosure front bottom handle.stl into 24 SL1S enclosure front bottom middle...

When I assembled my Prusa MK3 Enclosure using Queen City Polymers plexiglass (which was cut correctly) I found that the bottom corners were not thick enough and when tightened down were risking cracking the plexiglass. Print Settings Printer Brand:...

Sheetholder for Prusa Enclosure Print instructionsAny Material you want. 0,20mm Layer Height. ...No Supports</p>

Upper door stop for Prusa Enclosure or other modification. ...I recommend sticking Self-Adhesive Felt as https://www.aliexpress.com/item/4000619346973.html

Upper door stop for Prusa Enclosure or other modification. ...I recommend sticking Self-Adhesive Felt as where.Print SettingsRafts:NoSupports:NoResolution:0.2Infill:30%Filament material:PET-G

Normally, the Original Prusa Enclosure has a cable bushing for the rear ports, but not for the front. ...I remixed the front left door to feed the USB - cable of the EINSY board to the octopi and a flatband cable to a Pi cam inside the housing.

This is the second in a series of add-ons I've designed specifically for the i3, following these other projects: - Print Server: https://www.thingiverse.com/thing:2401423 - HEPA Filter: https://www.thingiverse.com/thing:2394452 - Spool Holder:...

This fixes the issue of the PSU being 1" too tall for the opening in the enclosure, and it also helped with the issue of the acrylic walls liking to bend too much around the printer, becoming wavy instead of straight. Print instructionsCategory: 3D...

This is a thermal enclosure for Prusa 3D printer. You mount a pair of these clips on the printer top frame (see photo), then make a rectangular wire frame from a clothes hanger, insert the wire in the the holes of the clips (see photo), then use a...

I didn't and then suffered the consequencesThe 27 SL1S enclosure front bottom vent.stl is not probably needed at all but I had it designed so I printed itPush 26 SL1S enclosure front bottom handle.stl into 24 SL1S enclosure front bottom middle...

Spool Supports for MP Maker Select 3D Printer v2 (and Prusa Mendel i3 3D Printers) The U/T bracket fits over the printer's frame to prevent sliding forward and backward. It fits snugly into a 1" PVC pipe, as seen in the printed examples. I use...

A freshly designed PSU holder for the Prusa Lack enclosure is now available. The initial holder fell short in terms of strength, and its orientation was not ideal. ...This new design allows the enclosure to be positioned closer to the wall, and cables...

I crafted a custom Prusa enclosure from scratch, but now I'm seeking a solution that incorporates filament storage as well. ...The clever design of double hinges allows for multiple door configurations, and I utilized the powerful 3D modeling...

This is an experiment to create a secure enclosure for my BQ Prusa i3 Hephestos.\nThe structure of the enclosure is built with 20mm square aluminium, boasting a thickness of 1mm, allowing me to place the filament spooler directly above.\nTo ensure...

All the parts for for my IKEA Stuva enclosure for the Prusa Bear. For the PSU case the following parts are needed: 3.5mm jack female XT60 The filament bearings and holders are for a IKEA Racka cut to length. The PSU mount nuts are optional but hide...

Filament scale mounting parts for use with the injection molded spool holder included with Prusa printers (I have an MK3S, not sure which exact models ship with it). ...This will replace the twist-in part.Designed to work with the Filament Scale...

Protecting the printer from dust is crucial, and maintaining a stable temperature during printing is essential. I also plan to experiment with various materials beyond PLA. ... Designs featured in the enclosure can be viewed on Instagram at...

My version of Lack EnclosureIt is essentially a remix of zuspiel’s design: https://www.thingiverse.com/thing:2012384However, I incorporated the use magnets similar to what LKM did: https://www.thingiverse.com/thing:1843235Enclosure I built uses 3...

... and the bottom corners. When I assembled my Prusa MK3 Enclosure using Queen City Polymers plexiglass (which was cut correctly) I found that the bottom corners were not thick enough and when tightened down were risking cracking the plexiglass. ...

After building the Prusa enclosure for my MK3S I really enjoyed the storage compartment provided in the frame, however I wanted to add a small touch to it with some dividers to keep my storage organised. I designed a little piece to match the storage...

I made the Prusa Mk2 Enclosure but i dont have the MMU upgrade. this is a single hole that allows you to run filament thru it. It is designed to have a PTFE tube fit inside it, for reduced friction. ...I printed it with PTEG To resist any high temps...

This is a revised version of the original Prusa Thermal Enclosure (https://www.thingiverse.com/thing:5235698). ... The revision is the addition of 1 inch offset to the wire elevation to make sure the print head does not bump into it when you do Z axis...

After building the Prusa enclosure for my MK3S I really enjoyed the storage compartment provided in the frame, however I wanted to add a small touch to it with some dividers to keep my storage organised. ... I designed a little piece to match the...