prusa pinda probe calibration 3d models

I made them on TinkerCad.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

More cargo for all of you Sci Fy tread heads out there.Freight Ten https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction Transport your Armoured Shelter...

It took me that long to figure out the config I downloaded that was tuned by someone for flex on my Prusa MK3S still had retraction on… at reduced settings, but the speed of the retraction was way too high. The finger would get almost to the top...

These are recommended print settings in Prusa Slicer: * PLA or PETG filament. * Start with "0.20mm Quality" print setting defaults. * Set supports to everywhere (accept all suggested changes), with these exceptions: * For the main case,...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Note the treads match in shape the body of the Freight Ten.Superglue the cab superstructure to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did...

 The TPU sticks pretty well to the Prusa textured sheet (while still being reasonable to remove), so I wouldn't recommend the satin sheet and definitely wouldn't recommend the smooth sheet, at least not without a separating agent.Regarding the...

Feel free to rescale as needed.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

Game Tokens - large and small!  For use in your next wargame!No supports are required.Grooved backside to facilitate easy grip even when soaked in the blood of your enemies.Plain-backed version for those unconcerned with being soaked in the...

Feel free to do whatever you want with them.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

NewsMarch 20, 2022 added bigger hookMarch 21, 2022 added USB flash drive holderMarch 21, 2022 added hooks (12mm and 25mm, screwed with M3 screw)March 21, 2022 added box (screwed with M4x10 screw)March 21, 2022 added 2 wall parts (224x190 and...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

I printed them at 20mm (4 hours or so,) but they look even better at 15mm.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

Pattern=Honeycomb I have use the Prusa I3 MK3s and I need the full 250mmx210mmx210mm space. I don't know whether and how the parts can be printed with other printers. But I am convinced that it is possible as long as the space is minimal...

Violence is never more than a heartbeat away.Keep your vehicles fueled!Stay in the fight!No support requiredResize for smaller or larger use. Designed on...

Don't let them destroy your home. Build! Get back in the Fight! Designed on Tinkercad.There are seven parts to assemble on the Attack Recovery Vessels.Two sizes - Large and Small.Stack for use or glue.The buildings are stackable, use...

Violence is never more than a heartbeat away.Shelter yourself! Deliver your cargo!Stay in the fight!Small painted-on supports are required for the following (Support Enforcers Only):Space-Port-OPEN-Module-PT1-V1Space-Port-OPEN-B-Module-PT2-V1...

Carefully align (see images.)Check that the Ramp swings freely, then Superglue a “small stub” onto the left side near the top to contain the “Ramp.” It must push out only a small amount to restrain the “Ramp” from opening. See the last...

While it is designed specifically for the Prusa i3 MKS series (working with the printer's filament runout sensor cable), it only actually requires a 5-volt circuit which is likely available on most printers. This board splits the input directly into...

(see the images).Superglue the nose to the body (see the images).Superglue the top deck.Leave the main gun to swing freely.Print supports only on the arches of the nose (that's how I printed it, it might print ok without them).Superglue works best...

...If you have something funky just adjust the necessary parameters in the .scad and print a customized version! Why I made this: I recently picked up Prusa's Multi-Material Upgrade 2.0 which unloads like 40cm worth of filament during filament changes.

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Use with your narrative in the hive or megalopolises of your wargaming environs.Print with “Fill Pattern” as "Adaptive Cubic" to save time and filament.No supports are required.Printed at .20mm Quality.Takes a little under 2 hours to print.Designed...

I wanted to wire tie the mount to the shelf (as I have done with the printers).The link below is to the USB cable.Amazon Basics USB 3.0 Extension Cable - A-Male to A-Female Adapter Cord - 3.3 Feet (1 Meter) -...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

Take what's theirs and make it your own! More Armour!Demolior Class Heavy Tank - https://www.printables.com/model/135967-tank-demolior-class-heavy-deathhead-ii-model-scien Scopulus Class Heavy Tank -...

Instead of being part of the fan duct (weak and difficult to focus), I created a hinged mount that connects to the Prusa X stepper motor. If you decide to use this option you should use it in combination with “Cooling duct with...

It adds time to the print, however, looks much better at the end.The Tank will scale up or down easily if you want a larger/smaller version.There is a full OBJ file of the assembled model (if you want to scale it down to epic scale of something like...

The Tower is 1m in high the outer cylinder is about 180mmPrintPrinter used: Prusa i3 MK3s+ Print Height : 0.2mm QualitySupport required for “cylinder inside” and “housing power supply”Printed Parts-Base plate -Housing power supply  ...