prusa octoprint 3d models

This housing enables the installation of a touchscreen with octopi/octoprint_tft on Prusa MK3s printers, specifically designed for space-constrained environments where the touchscreen must be mounted on the side of the printer. It sits atop the power...

I'm designing a Raspberry Pi 3 model B mount specifically for my Prusa i3 rework's aluminum frame. The mount clips onto the frame, and the case simply slides into place. To secure it all, I just need to tighten two short M3 screws or bolts. ... This...

This is a Remix of Raspberry Pi 4 - OctoPrint Prusa Mount (MK3/MK3S) with more clearence for the USB-cable.The housing used is Malolo's screw-less / snap fit Raspberry Pi 4 Model B Case, because it is configurable and fits perfectly without screws.I...

This is a unique remix of the Raspberry Pi case tailored to fit the 3030 extruded rail on the Prusa i3 MK3. I added an open hardware logo to give it a personal touch. To achieve this design, I used the following print settings: three outlines and...

M3x6 will work in a pinch and M3x10 will stick out a bit but will clear all moving parts.April 2021 Update: Added a version sitting lower on the frame to clear the excellent LED Light Bar Prusa i3 MK2/MK3. The mount uses different screw holes and...

This item replaces the bottom of a Geekworm Heavy Duty Aluminum case for RPi4, mounting in the back on a Prusa MK3/S frame above an electronic box. The Geekworm Heavy Duty case is a generic, inexpensive aluminum case for the RPi4 designed for...

Just simple case for raspi 4B powered by a Prusa power supply.You will need:PET-Gbuck converter 24V/5V, 3Awiresconnectors (see the pictures)2 x M3 hot melt thread insert nuts4 x M3 screwstime :)

OctoPrint Connection Cable Organizer for Prusa MK3 USB Cables

Snaps on to Malolo's screw-less/snap fit case, screws to MK3 frame, but raises it up about an inch so that there is a bit more room for plugging in USB and ethernet cables.Other remixes I found (and printed) were a bit flimsy. I also didn't want to...

I took pictures with this sitting on my mini, but printed them on my Ender 3. :D EDIT 03-10-2020: I just added the Pi cover part because I realized that I extended the face of the Pi case by 1.8mm and didn't change the cover to match. It's a small...

Sooo, I took the pictures with this sitting on my mini, but I printed on my Ender 3. :D EDIT 03-10-2020: Just added the Pi cover part because I just realized that I extended the face of the Pi case by 1.8mm and I did not change the cover to match. ...

<p>I remixed this from Malolo and Haz1's ideas for a frame mount for the RasPi right above the Einsy board. There was a Raspi 4 model, but not a 3B, so I snipped and clipped them together :)</p><p>You can mount it using an M3x10 screw from the spares...

This is a remix of ChrisPetit's outstanding raspberry pi case. I flipped the lid and base and shifted the whole structure to the right. The goal was to create extra space for attaching hats, cables, etc. to the raspberry pi. I also expanded the...

OctoPrint/OctoPi Camera configuration for Prusa 3D printer MK3S(+)This configuration is used for monitoring and controlling a Prusa MK3S(+) remotely using the OctoPrint software suite (https://octoprint.org/) an RPI4B (https://www.raspberrypi.org/)...

If your printer does have such an out-of-print area, take a look at Simple Automatic Nozzle Cleaner for remote control (Octoprint).This Automatic Nozzle Cleaner remix is based on the original design from “BigBrain3D” of his Purge Mechanism and a...

I won't be held responsible if this causes you any injury or worse!This is a customized Prusa MK2/MK2.5 PSU cover to fit a DC-DC converter and provide 5v power for a Raspberry Pi.It should fit this...

This revised design can be easily clipped into place without requiring the removal of screws or the use of an extended screwdriver.

I loved the original design, but had to make a few modifications to get it working perfectly with my Mendel I2. Rather than using a stand-alone setup, I opted for mounting it directly onto the printer's frame. The same case design worked beautifully,...

I'm setting up support for my OctoPrint. This is my very first creation. ...Good luck with your printing endeavors!

LCD panel that works with the awesome Hyperpixel 4" touchscreen with Raspberry Pi4.This is for: MK3/MK3S/MK3S+ and Pi4Yet another remix of the 4” HyperPixel cover for the Prusa MK3S+ for the Pi4 to be used with Octoprint and Octodash. The goal of...

I mixed the mount arm I liked with the case I liked for the Prusa MK3S and Raspberry Pi 4 to use with OctoPrint. I created a basic mesh case, one with a ribbon cable slot, a case for a 30mm fan, and a 30mm fan with ribbon cable slot.</p><p>With the...

I combined the Prusa MK3S mount arm that I liked with the OctoPrint-compatible Raspberry Pi 4 case, creating a custom setup. The result was a basic mesh case design, along with a separate enclosure for a 30mm fan and another version of the fan case...

This is a multi color remix of the MK3 RPi + piTFT cover by acorderob. Changes Added trim details for multi color Made the X button larger Added a RESET word For the touchscreen Raspberry Pi 3 B+ with CanaKit 2.5A Power Supply I plan to update...

I used the original source on a Raspberry PI 3 B+ and the heatsink did not fit, so I opened a window for giving space to the heatsink.

I'm examining the original for context and guidance. I've modified the Raspberry Pi case to include a fan mounting point. ...Please ensure that you secure the fan prior to inserting the Raspberry Pi board into its enclosure.

This is for: MK3/MK3S/MK3S+ and Pi4 Yet another remix of the 4” HyperPixel cover for the Prusa MK3S+ for the Pi4 to be used with Octoprint and Octodash. ... Complete details and build instructions are here:...

... oder ggf. eure Wünsche auf zu nehmen.@Dear Prusa Team:Don't give up the Prusa Mini and keep on developing it as the best compact 3D-Printer.&nbsp;Danksagung:Danke an die Entwickler von Prusa Slicer&nbsp;Danke an die Entwickler von FreeCAD 0.19

I wanted to give my case an extra touch of personality, so I chose to use a design that highlights the Octopi/Octoprint setup I'd be using to control the printer. ... I've included the fusion 360 file in case anyone wants to make any further...

I created this for a friend so he could mount a touchscreen to the top of his Geeetech A10 and control it via Octoprint-TFT. It will fit on any 2020 V-slot, making it compatible with many printers. ... You'll need to print: - 1 x Case bottom - 1 x Case...