prusa mk3s raspberry pi 3d models

The Raspberry Pi Zero2 is such capable yet small machine that fits perfectly with Mini. So I modified the display box file and added this side mount for the pi zero. No support needed.Ideally one should use the w version without the GPIO pin...

I fitted a tensioner and installed a mounting bracket on the Pi 3.

I use it with Octoprint on a Prusa MK3S+.You simply once run sudo raspi-config->performance->Fan Enable, set the GPIO port (I use 14) and the temperature (I set for for 60 cen). See attached illustration for wiring.Update October 21st, 2023 - New...

This is a quick and dirty modification of an existing Pi 4b case:https://www.thingiverse.com/thing:3852672to fit on the mk3s frame and fit under this light bar (the dual light):https://www.prusaprinters.org/prints/3267-led-light-bar-prusa-i3-mk2mk3I...

This is a remix of [Malolo's Raspbery Pi 4 case bottom](https://www.thingiverse.com/thing:3723561), made for the Prusa Mini and Mini+. The case will attach to the printer directly behind the LCD screen on the frame, using 2 T-nuts and 2 M3x20 screws....

Important note: This mount was specifically designed for Raspberry Pi's OEM v2.1 Camera. Using any other camera may result in damage to the camera. ...Most fit issues are caused by non-OEM cameras, so please use caution when experimenting with...

I recently switched from octoprint to Prusa Connect and no longer needed a screen. I also wanted to go back to the original dash on my Prusa-Box. The only thing missing was the switches for lights and exhaust fans. I took the dimensions from the...

:D EDIT 03-10-2020: Just added the Pi cover part because I just realized that I extended the face of the Pi case by 1.8mm and I did not change the cover to match. It's a small detail, but one that would annoy me. Remixed the RPi 3+ case by lab27 to...

:D EDIT 03-10-2020: I just added the Pi cover part because I realized that I extended the face of the Pi case by 1.8mm and didn't change the cover to match. It's a small detail that would annoy me. I remixed the RPi 3+ case by lab27 to house an Rpi...

This is a fixed short arm raspberry pi zero camera mount for the prusa i3 MK3S. Designe was mainly derived from these three thingiverse creators:- https://www.thingiverse.com/thing:3802104 https://www.thingiverse.com/thing:3485960...

... Be 2 Centimeters Thick to Align My USB Cable Properly with the Rambo Mini. Printing at 100% Should Provide Adequate Results. Print DetailsPrinter Model: Prusa i3 PlusRafting: Not ApplicableSupports: NoneResolution: 200 MicronsInfill Percentage: 22%

I chose this specific PoE hat for my Pi 4, as it provides more power than the official option available: https://amzn.to/2uOIng2. To connect the Pi to the RAMBo, I use a short 6-inch USB cable: https://amzn.to/2PFtGTK. This connection ensures that...

Despite of the huge amount of ventilation, the Pi still got over 50°C. So a 40x40 fan was put on the front side. ...But it was too high so that the mounting screw was not reachable any more.I moved the case a bit. The cover fits from the original...

... my USB cable neatly through to the Rambo mini board without any complications. Since the settings should produce an optimal result, I'm running the prints at 100% scale. Printer: Prusa i3 Plus Rafts: No Supports: No Resolution: 200 um Infill: 22%

This is a remix from https://www.thingiverse.com/thing:4613758 and https://www.thingiverse.com/thing:4165611 The case from https://www.thingiverse.com/thing:4613758 allows you to mount a Raspberry Pi3 under the LED Light Bar Prusa i3 MK2/MK3...

I've designed this holder with ease of installation and removal in mind, directly from the Prusa MK3 frame without needing any tools. The holder is specifically crafted to fit the case found at https://www.thingiverse.com/thing:3001109, created by...

... holder to your printer with just one screw. ...The ball allows you to pick the camera's orientation for use with octopi. Print Settings Printer Brand: RepRap Printer: Anet A8 Prusa I3 Rafts: Off Supports: On Resolution: 0.2mm layers Infill: 20%

... 4 x M3 5mm with optional washers. ...Be sure not to tight them too much or you may end up having issues on your display! PRO Tip: If you use a Raspi Cam with a long enough wire, you can run it behind the Prusa spool holders for added secureness! ...:)

... can damage your display. To avoid this, be gentle when tightening the screws. PRO Tip: Consider using a Raspi Cam with an extra-long wire. This will allow you to route it safely behind the Prusa spool holders for added stability and peace of mind!

The holder is desing to fit the case: https://www.thingiverse.com/thing:3001109 by dghoti Thanks to him for the case Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: No Supports: Yes...

... power output. Cooling ribs widened to promote better cooling when enclosed for ABS printing. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Resolution: 0.2mm Infill: 30% Gyriod ud83dude32 Category: 3D Printer Accessories

After updating my extruder with the new [mount](https://www.prusaprinters.org/prusa-research-summer-update-2018/#cooling) for better cooling, my front fan collided with the camera mount due to its changed position. I extended the arm 1.5 cm to...

... the Nema 17 stronger. ...Print Settings Printer: Prusa Mini Rafts: No Supports: No Resolution: 0.15 mm Infill: 15% Filament: Amz3D PLA Black Notes: If the motor gets too hot, it should be made of PETG instead... ... Category: 3D Printer Accessories

In May 2019, I added prusa_plate_camera_mount_v4.stl as the original design might collide with the Z-axis motor on the left side during bed calibration phase. The camera end of the mount now has a bit more distance. ...One day, I might even clean up...

After update my extruder with the new mount (https://www.prusaprinters.org/prusa-research-summer-update-2018/#cooling) for improve cooling my front fan crashed with the camera mount because it's new position. I made the arm 1,5cm longer to avoid...

Also connected the ballnut with slightly modified fflink as I don't need them as separate parts All the original parts from https://www.thingiverse.com/thing:3114849 are printed with 3 outer perimeters and 15% infill which seems to create rigid...

Raspberry pi

I wasn't happy with many of the camera mounts for the Prusa Mini, so I designed one that I love!The camera is mounted on the x-axis motor with a customizable angle to suit your needs.The design is simple with 4 printed pieces and a little hardware...

Prusa included this feature for a reason; it prevented the filament wire from moving around and potentially damaging the delicate electronics within. When printing this design, take note of the tiny vertical tube on the main case's wall where the...

It should be adaptable to any Prusa i3 X carriage using a Nema 17 motor. The camera position will move with the Z axis, providing an immersive view of the object being printed. Keep in mind that I'm not a skilled 3D designer, so I hope this one will...