prusa mk3s part cooling fan 3d models

Designed up this for the PArt cooling fan 4020 for the prusa mk3 or bear upgrade Printing: Ring - Infil to add weight, supports needed for spade inset. Letter embossing doesn't need it. Spade - Infil to add weight, no supports Letters - Print...

... air pointing at the nozzle instead of the part. This modification solves this issue by giving the part cooling fan a second point of support far away from the hotend, keeping the part cooling fan level and out of range from hitting your model.

I was let down by the standard Prusa cooling fan duct because it obstructed my view of the nozzle, yet performed well overall. I sought a straightforward, compact, bolt-on replacement that wouldn't require relocating the fan, drilling holes, or...

I added that file as an option (the differences are moving the mounting hole up 1mm and shaving 1-2mm off the rib in the middle where the fan duct connects to the fan). Note: I use a non-standard nozzle that's a tiny bit taller than the standard...

(Differences: moved the mounting hole up 1mm & shaved 1-2mm off the rib in the middle of the area where the fan duct connects to the fan.) NOTE: I use a non-standard nozzle that is a tiny bit taller than the standard e3dv6. If you find the "easy...

Prusa released the printable parts for MK3s+ and the fan shroud is much better than the stock one of the Mk3s, so, for everyone who don't want to fully upgrade from Mk3s to Mk3s+ but still would like better cooling, I cut the second mounting point on...

The mounting holes on the part cooling fan for Prusa i3 printers are generously sized at approximately 4.3 millimeters. Excessive torque applied to the mounting screw can cause it to damage the hole and become lodged inside. ...Fortunately, these...

Prusa released the printable parts for MK3s+ and the fan shroud is much better than the stock one of the Mk3s, so, for everyone who don't want to fully upgrade from Mk3s to Mk3s+ but still would like better cooling, I cut the second mounting point on...

The mounting holes of the part cooling fan for Průša i3 printers are quite wide, something about 4.3mm. ...If the mounting screw gets too much torque, it damages the hole and sinks inside.These inlays prevents this.Print SettingsPrinter Brand:...

SEE VIDEO HERE https://youtu.be/xPJshCr5V6E The Tukkari TS enclosure, in this example, for Prusa Mk3s does not include a PSU shroud between the PSU and honeycombe vent plexiglass side panel. This accessory in PETG provides a bolt on shroud to...

To print with a slower fan speed is a problem, because Prusa's system is set up in the firmware to run its stock fan, which is 5V/3A, but with an RPM of 4,500. Why does this matter? Well, we have to understand that the fan has feedback, a yellow...

I've recently acquired an older MK3 fan that dates back to when I upgraded from an MK3 to an MK3S, and it features a centered notch in its design - a distinct difference compared to the layout found on Davidewen's model. ...To optimize this notch for my...

Nevertheless, the "Adapter-Printer" does not necessitate a cone for precise placement since the surrounding extruder parts ensure exact positioning. It is highly desirable to have this "Adapter-Printer" easily removable due to its location in the...

Fan cover for prusa i3 mk3s. ...Optional, purely decorative

This is a part of a cooling fan, made by me.

Antonio Guardia designed this part cooling fan project specifically for the AGraber 30i.

heat sink size 40 x 40 x 11 mm Check out this high-quality heat sink on Amazon: https://www.amazon.com/Easycargo-40x40x11mm-TEC1-12706-Thermoelectric-40mmx40mmx11mm/dp/B07B66GK7Z/ref=sr_1_8?keywords=heatsink+gold&qid=1561990882&s=gateway&sr=8-8 Fan...

This cooling duct was designed specifically for a Prusa 3D printer from China. The car is positioned at a 45-degree angle, which I hope will be helpful to someone out there. I created this duct in SolidWorks 2013 and it worked perfectly with my old...

I modified my Climber7 part cooling fan using "Plasticene" and noticed an improvement using PETG, so I'd thought I'd set about making a STL model to refine the idea. There are some volume constraints with this part within the hot end enclosure, so I...

... extruder should have only one nut on the extruder. This works with a 40mm fan, and the m3 screws to screw the fan in. In the picture you can see that I put nuts on the other side to hold the fan in place. ...This part was made for my delta printer.

I hated my old stock fan so much that I decided to build a brand new one from scratch, and now I'm itching to upgrade and refine it even further.

This is a completely redesigned fan shroud for the Prusa i3 MK3S/+, which not only delivers fantastic airflow like the old Mk3 shroud did, but which also sits far away from the heatblock and will not melt when printing at high temperatures. To...

Buy a 24-volt fan from Amazon and plug it into the LED connector on the board. ...You'll be able to turn it on and off by hand, or program your slicer to do the job for you.

This is my Prusa MK3S fan shroud modified a bit. I had trouble cooling the back side of objects that print. The design is symmetrical - the front overhang printed just fine but the back was melting. So, I took the original Prusa fan shroud, split it...

... the design and would love to see more stuff like this, please leave a comment below. ...Also, don't hesitate to contribute with a tip – all funds will be used to buy more equipment and develop new upgrade parts for the hobby. ... How I Designed This

This is a completely redesigned fan shroud for the Prusa i3 MK3S/+, which not only delivers fantastic airflow like the old Mk3 shroud did, but which also sits far away from the heatblock and will not melt when printing at high temperatures.To orient...

Modified Remix to Clear Prusa MK3S Hotend Fan Clearance To allow for smooth printing on the Prusa MK3S, a slight modification has been made to the hotend fan clearance. This adjustment is crucial for optimal performance. *Important Note*: The...

... and accuracy. The design fits seamlessly. This GCode is specifically tailored for Prusa MK3S users only. ...Version 2 offers refined improvements, including a streamlined front mount area and elimination of the unnecessary rear lower cutout.

Fan mount and air flow duct to allow the use of a larger and more powerful Noctua (or other 40 mm) fan to improve the cooling of the cool end of the extruder. This will help when printing PLA in particular to avoid heat creep issues.The part is...

Outside the enclosure I mounted an 80mm PC fan. It's a new design and time will tell if it improves the rate of success or not.Note: The box should not interfere at all with the moving parts of the printer. You may need to change the printer...