prusa mk3s part cooling fan 3d models

I'm tackling a new project, one that promises exciting developments by next autumn, and in preparation, I required a custom fan mount measuring 30mm, integrating a part cooling fan into its design. ...Quickly sketching out the concept, I was pleased...

11/16/2023: both front and rear mount are updated to allow for adjustment of angle and distance, works best with the 75A TPE nozzle in my designs 10/21/2023: Updated design improved angle of mount for increased velocity and part cooling eficacy use...

I needed a better part cooling fan for my Tronxy X5S that directs air to the part instead of the hotend, while keeping the metal enclosure intact for fire protection against potential hotend issues like loose heaters or thermistors. I also wanted to...

So i hade a bit of problem with the print fan shroud starting to get soft and dropping down on the right side (that is unsupported) when i was running print with huges first layers so the print fan was not on for a long time. I grabed the STL from...

I've been searching for a part cooling fan that fits my setup and after countless iterations, I decided to build my own instead of giving up. I found a great cooling fan mount for the E3D Heatsink on Thingiverse...

This is a modified version of the original remix from Agarajag and AlxMoon, taken from hackoholic.\r\n\r\nTo enhance airflow and thermal performance, I've recessed the top case by 1mm where the fan fits, allowing me to install a thin 30mm fan (7mm...

Since Prusa has improved its cooling with the MK3s+ I added the Fan Mount to use the cooling holes. ...Since i also use a PTFE Tube to my Extruder to reduce stress on filament/extruder.

Although Prusa's supportive documentation assures me these temperatures are normal, out of caution and anticipating future prints with ABS in an enclosure, I decided to create a small fan bracket to clip directly onto the Extruder motor. Cold air is...

Minor refinements This is a mod to replace the OEM part cooling fan for a 4020 fan & ABL sensor It involves cutting away a small section of the OEM hot end housing sheet metal (cut area shown in pic) however it is reversible should you want to go...

Although the kind Prusa support team assured me that these temperatures were within acceptable limits, I still had my doubts, especially considering my future plans for printing ABS in an enclosure setup. To err on the side of caution, I decided to...

The user adjusted the printing angle to 45 degrees, ensuring the Shroud wouldn't collide with the Print bed on their MK3S. ...This modification is a revised version of the original design found at thingiverse.com, specifically thing number 3533859.

Minor refinements This is a mod to replace the OEM part cooling fan for a 4020 fan & ABL sensor It involves cutting away a small section of the OEM hot end housing sheet metal (cut area shown in pic) however it is reversible should you want to go...

It's a clever combination of my Bear-BMG fusion duct and Jonathanrswift's original Bondtech extruder dual fan duct. I've also added an optional new front cover that subtly adjusts the bottom screw hole support to allow for a snugger fit, ensuring the...

Remix of https://www.thingiverse.com/thing:1746358I wanted to use the original version together with this Bondtech mount for my HEVO:https://www.thingiverse.com/thing:2768735But I needed to mirror it, so I modified it to be used with a 4010...

... setup for the Tronxy X1. I wanted to have a part-cooling fan that doesn't block the view of the hotend, while also allowing good airflow with as few sharp corners as possible. ... I hope you like my version and I welcome any feedback to improve it.

This quick modification is made directly in Fusion 360 to enable print cooling on my MK2.5S with Volcano hotend. It's not fine-tuned or flow-tested at all, I simply roughly extended the standard shroud. ...Use ABS or a similar high-temperature plastic...

As a result, the tmc2130 components now require enhanced cooling systems to prevent overheating issues. To verify compatibility with the original frame, I conducted rigorous testing on a modified bear upgrade frame. ...Please inform me if this upgraded...

This is a remix of RosyRL's amazing dual-fan shroud design that allows for an endoscopic camera to be used as a nozzle camera. You can pick one up for AUD$10 on AliExpress. ...They're about 8mm in diameter.

Also, the fan shroud is not sold separately from the Accessory packNOTE: This is for the Slice Engineering Mosquito version, not the copperhead.I printed mine in Siraya Tech Sculpt High Temp Resin - GreyI have not attempted to FDM printing this but...

The duct is fabricated from sturdy materials to provide optimal airflow and support, ensuring that your cooling system operates at peak efficiency. ...By redirecting hot air away from the CPU, this solution helps maintain a stable thermal environment...

Prusa mk3s+ Extruder Cooling + fscover with M10 pneumatik mount for ptfe Tube

On some of my more complex 3d print designs I have found that the stock Prusa part cooling duct that blows only from the front is not enough. Steep over hangs and details on the back side of the build plate seem to suffer. Since Ultimaker uses two...

Remixed (https://www.thingiverse.com/thing:2826255) Version Optimized with Original E3D V6 30mm Hotend Adaptor to Boost Dual 40mm Part Cooling Capabilities. ... This highly compact design is specifically tailored for maximum mobility on a kossel delta...

Prusa mk3s+ Extruder Cooling + fscover with M10 pneumatik mount for ptfe Tube Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts: No Supports: YesResolution: 0.16 Infill: 25% Filament: Polymaker Polyflex TPU Black Category: 3D Printer...

Mounted on the printer using hardware that came with the printer. It is designed to work with the 40mm blower fan from Creality. The fan can be locked in with two small pieces of filament through the mounting holes. I used the Lined support material...

On some of my most intricate 3D print designs, I've discovered that the standard Prusa part cooling duct, which blows air solely from the front, is insufficient. Steep overhangs and fine details on the backside of the build plate seem to struggle as...

...for better air intake, the fan is rotated 180 degree (same idea as already used by many SK-Go² users), now just with the hole for new ABL sensor Ernest is shipping with the kits... The E3D V6 should also fit on the TringleLab Dragon (like I am...

... fan from Creality. The fan can be locked firmly in place using two small pieces of filament through its mounting holes. Lined support material was used, allowing for easy removal from the cavity. ...Feedback and revisions are always encouraged!

I wanted to pair the original version with this Bondtech mount for my HEVO: https://www.thingiverse.com/thing:2768735 But needed to flip it, so modified it to be used with a 4010 blower And also, I wanted to use a 40mm instead of a 30mm fan The...

...for better air intake, the fan is rotated 180 degree (same idea as already used by many SK-Go² users), now just with the hole for new ABL sensor Ernest is shipping with the kits... The E3D V6 should also fit on the TringleLab Dragon (like I am...