prusa mk3s enclosure v2 3d models

... cables depending on your setup; I'm using a raspberry pi 4, so my cable needs to reach from the back of my case. The Raspberry Pi v2 camera can be purchased at https://amzn.to/31ytxrX and I highly recommend this cable set: https://amzn.to/2NLIcbg

The first version of this MMU2 buffer ( https://www.thingiverse.com/thing:4138220 ) was a significant improvement over Prusa's stock version, loading/unloading and printing are a lot smoother. I had a 5 days print , with 2400 layers and 2200 filament...

The first version of this MMU2 buffer (https://www.thingiverse.com/thing:4138220) was a significant improvement over Prusa's stock model, loading/unloading and printing are much smoother now. I completed a 5-day print with 2400 layers and 2200...

Pi Camera V2.1 Mount With Optional X Axis Cable Strain Relief for the Prusa MK3S & MK3S+ Printers. Note: added mount for MK3S+ (MK3SPlus_X-Axis_Bracket_Pi_Camera_Mount v1.stl). This is the only part that differs from the original MK3S. After...

This is mix of print files from https://www.prusaprinters.org/prints/23923-lack-enclosure-v2-modified-to-print-on-the-mini and https://www.prusaprinters.org/prints/3673-mmu2s-enclosure to print Ikea lack enclosure on prusa mini without gluing...

Simple Prusa MK3S/MK3S+ display cover. For those who use a seperate display to control the printer or simply do not want to see the blue display all night lighting up the room.  The cover tightly fits right into the display holder and...

Note: mounts the PSU towards the inside of the enclosure so it does not stick out from the perimeter of the enclosure and lines up the DC wiring connection area of the PSU with the large wire passthrough port on the TARCA enclsoure. Uses M5 x 8mm...

If you have a problem to find 3 mm plexiglass for Prusa MK3s Ikea Lack Enclosure, you might be able to get a 2.5 mm version - so here you have a remix of Prusa Enclosure parts for 2.5 mm plexiglass.Parts, which didn't need to be edited, are available...

So i printed this: https://www.thingiverse.com/thing:3863115 It´s to large so the printer needs to be higher up. ...Just print four of them and make sure you put them on tight on the original rubber feet of the mk3s.

So i printed this: https://www.thingiverse.com/thing:3863115 It´s to large so the printer needs to be higher up. ...Just print four of them and make sure you put them on tight on the original rubber feet of the mk3s.

I also minimized the middle opening, cause in my opinion most of the air just streams down and is not used for cooling.In my testing against the stock shroud, overhanging and bridging looks way better.I´m not sure, if the side openings are big...

... shroud, overhanging and bridging looks way better. I´m not sure, if the side openings are big enough, so please comment your thoughts or remix the thing as you like. There is also a modified shroud for the MK3S without the second mounting point.

I also minimized the middle opening, cause in my opinion most of the air just streams down and is not used for cooling.In my testing against the stock shroud, overhanging and bridging looks way better.I´m not sure, if the side openings are big...

Remixed text on cover for latest Prusa printer versions. Optional color change possible at layer height of 1.6mm. Printed main part in black so LCD would show through. Picture is without flash and LCD is fully lit. ... This blocks the light...

SEE VIDEO HERE https://youtu.be/xPJshCr5V6E The Tukkari TS enclosure, in this example, for Prusa Mk3s does not include a PSU shroud between the PSU and honeycombe vent plexiglass side panel. This accessory in PETG provides a bolt on shroud to...

Inspired by the Voron 2.4 enclosure I made my own for the Prusa i3 MK3S+. Exterior Dimensions are 614 x 556 x 518mm.The Case is sealed from all sides but air can still flow in from below to vent the electronics. The whole enclosure sits on...

I designed this 3D Printer 1.75mm Filament Feed Guide for my Prusa i3 MK3 after building a two-tier IKEA Lack Table based enclosure to store a pair of printers. The twin-story configuration made it impossible to feed the filament from above the...

I designed this 3D Printer 1.75mm Filament Feed Guide for my Prusa i3 MK3 after building a two tier IKEA Lack Table based enclosure designed to store a pair of printers. Due to the twin storey configuration it wasn't possible to feed the filament...

I was able to get by with the spare hardware from the MK3S kit. You only need to download either the Pi3 case or the Pi 4 case, depending on the RPi you have. The RPi3 case is the same as the source Thing. My Pi 4 case will fit on to the source's...

Custom Components Fabricated for My DIY Project. ...Detailed Explanation Below.

KNOB FOR PRUSA MK3S WITH PETG AXES

Hi, My enclosure is different from the rest. I'd like easy access to the MMU when it is jammed. So I figured out a different enclosure. Have fun.... Print instructionshi, Don't be affraid to enlarge the MMU cable to the printer. This needs to be...

Support arm with better teeth shapes for Prusa Enclosure V2, fits in all positions, even in the lowest position.

Diseño de cubierta LCD para prusa MK3s personalizado con cuadros.

the ist for a Prusa MK3S 3D Printer

A little SideBox for the Prusa Mk3s 3D-Printer.

Úložné boxy na tlačiareň Prusa i3 MK3S+

This is a remix of the Prusa V2 lack enclosure's lower left rear bracket, with an opening for cables. ... The V2 lack enclosure has an option for a cable passthrough on the lower right for the AC line, but I wanted an option on the left for DC...

Added extrusion for bearings in spool centers for https://www.prusaprinters.org/prints/3673-prusa-enclosure-v2-mmu2s Uploading here to share the STL for others to print with a different printer.

Update 04.02.2020 Added split version of V5.6.1, split by nimaim https://www.thingiverse.com/nimaim/about ---------------------------------------------------------------------------------------------------- Update 02.02.2020 Added newer Version based...