prusa mk3 enclosure 3d models

A compact enclosure with fundamental joints and a protective shell for affordable webcams.

I'll be remaking the holders to hold a bar for my lack of enclosure, Can't promise the expanded works will function properly since I haven't put it through its paces myself.

This is a remixed door handle for the Semi-Official Prusa MK3 Enclosure Project (https://goo.gl/ssr5fm). I found that the magnets are hard to come by for the handles, so I remixed the handles to allow the use of the same magnets used in the extruder...

Building the enclosure "Original Prusa i3 MK3 ENCLOSURE - Ikea Lack table - Prusa Research by cisardom Apr 16, 2018" with three tables where you have to mount the middle one to the lower one. This is my solution. I like them because I got a lot from...

The OpenScad / Customiser file can be used to produce eight custom enclosure corners, fully compatible with the [Original Prusa i3 MK3 ENCLOSURE -Ikea Lack table https://www.thingiverse.com/thing:2864118] The following features are available: •...

Here's my take on the ball bearing rollers for the Prusa i3 mk3 enclosure. There are a few variations, but one version has a nice fit where the axle can't turn and can be printed without supports. ... I've added an edit to this post on September 10,...

Here, I combined the Original Prusa i3 MK3 Enclosure adjustable spool holder (https://www.thingiverse.com/thing:2864118) with the Prusa i3 MK2(s) & MK3 Spool Holder (https://www.thingiverse.com/thing:1832235), which has effectively resolved the...

Here, I combined the Original Prusa i3 MK3 Enclosure adjustable spool holder (https://www.thingiverse.com/thing:2864118) and the Prusa i3 MK2(s) & MK3 Spool Holder (https://www.thingiverse.com/thing:1832235) which has resolved the problem. There is...

So I needed to flip the direction of the moveable part of the 'Adjustable Spool Holder for Original Prusa i3 MK3 ENCLOSURE '. Because of the flip, I was unable to fit 2.3kg spools. ...This extender can slide over the screw I mounted the original with,...

I created this basic holder specifically for the Amazon Basics Sample 'spools' that I purchased online. The filament won't roll onto the holder as intended, so you'll need to unwind a few loops and let the remaining coil rest on the holder instead.

To utilize four-millimeter plates, simply incorporate those components into your design.

My First Design in Fusion 360 Was a Steep Learning Curve, But I'm Very Proud of My First Result. I recently created a simple sliding drawer frame to fit under my Lack table - it's available here: https://www.thingiverse.com/thing:2864118. For the...

I was a bit concerned about exposed magnets both visually and as regards magnet damage, so this is a simple remix to move the magnets to be semi-enclosed and less visible. They will now attract through plastic. It should reduce magnetic pull and...

Remixed top corner brackets enable the use of original hardware from the Lack table. To assemble, you will need bottom corner brackets and other components from the source device. Visit https://www.thingiverse.com/thing:2864118 to access the...

I managed to salvage just one component, so I ended up needing only a single one. ...I designed it using SolidWorks instead of Fusion 360.

I made a remake of a remake to address some problems I encountered. The spool holder wasn't compact enough for my eSun spools (64mm outside diameter). Additionally, the wheels were overly tightened onto the axle. ...To solve this, I expanded the inner...

I repaired the corners a bit, recessed the screw holes, and repositioned them for the top corners because they didn't match the original holes. Now you can use Ikea threaded bolts. The rear lower corners now both have cable glands, and you can adjust...

I was a bit concerned about the exposed magnets both visually and as regards to magnet damage and glue failure so this is a simple remix to move the magnets to be semi-enclosed and less visible. They will now attract through the plastic. It should...

Check out the official Prusa product at https://www.thingiverse.com/thing:2864118. ...This design extends your Prusa enclosure, allowing you to store filament in a secure box.

These are the separate top corner pieces for the Original Prusa I3 enclosure, as the entire model wouldn't fit within my printer's build volume due to its complex part arrangements.

3mm leg spacer for Ikea Lack enclosure. ...Scale in Z to fit your needs.

I'm trying to print out individual parts from this design because I want to build my own enclosure for my Ender-3 3D printer. However, the pre-grouping and awkward placement of the parts make it hard to print them correctly, especially if you have a...

EDIT: I do not intend to use this design for my Ender-3 enclosure, but I'm keeping the parts up for those that need separated parts for whatever reason. I am trying to print these parts, as I would like to print my own enclosure for my Ender-3, but...

What You'll Need: Print: 1x Prusa_Enclosure_Top_Corners_2.5mm Or 3mm Version 1x Prusa_Enclosure_Bottom_Corners_2.5mm Or 3mm Version 2x Prusa_Enclosure_Door_2.5mm Or 3mm Version 1x Prusa_Enclosure_Filament_guide Plexiglass Dimensions: 2pcs: 435 X 440...

What you'll need : Print : 1x Prusa_Enclosure_Top_Corners_2.5mm or 3mm version 1x Prusa_Enclosure_Bottom_Corners_2.5mm or 3mm version 2x Prusa_Enclosure_Door_2.5mm or 3mm version 1x Prusa_Enclosure_Filament_guide Plexiglass dimensions: 2pcs: 435 x...

I've added slots for 10x2mm cylindrical neodymium magnets. ...Simply insert them using a screwdriver, and you'll be all set.

Based of fandabrabec design. Had magnets left over from my KlackEnder project and figured id put them to use instead of buying the rectangular magnets. ...Enjoy.

I made this for a buddy and thought I'd pass it along. ...Check out a compact version of this design in Tinkercad, tailored for those with smaller build areas who still want to print an all-in-one solution.

This design features a simplified foundation for the spool holder assembly.

This is a remix utilizing six three-millimeter magnets available at Amazon. ...They can be found under the product code B01FD43RNO.