prusa mk2s 3d models

Modification with profile 40mmx40mm from "GILTEC" Profile: 370x40x40x40 - Qty: 3 310x40x40x40 - Qty:2 325x40x40x40 - Qty:2 Rod Ø8 long 360mm screws M3 M6 M6 M8 Calibration Z, observe the 25mm dimension with the M3 screws on the upper Z bearings.

This is a remix for smaller printers than the one used by the creator, as my Prusa MK2s cannot print large parts. The "short_box_2_si" design has been shortened to fit four slots, which are represented by the green boxes in the attached picture. It...

The wobbly X and Y idlers on my Prusa MK2s were driving me crazy, even though prints came out OK. The wobble originates at the 3mm bolts that act as axles for the idler pulleys... First, as the bolts are threaded and not precisely sized there is...

The best active antivibration stock for the Original Prusa i3 MK2/MK2S likely works with the new MK3 as well. To install it, you'll need 6 springs, 2 nuts, and 2 screws. This upgrade is specifically designed for PLA filaments only; its effectiveness...

Extruder assembly for Prusa i3 MK2S upgraded with a newly designed PINDA probe holder, extending 8.1 millimeters.

I have modified the y-belt holder, available at https://github.com/prusa3d/Original-Prusa-i3/blob/MK2S/Printed-Parts/stl/y-belt-holder.stl, by adding 10mm to its length. This modification should allow it to hit the y-axis end stop. To implement...

Bearing holder for MK2s Category: 3D Printer Parts

Bearing holder for MK2s Category: 3D Printer Parts

Here are the three parts needed to adapt the Retractable Purge Mechanism for the Prusa i3 MK2 & MK2S: Purge - Mount_Right - MK2.stl, Purge - wedge - MK2.stl, and Purge - Bracket - MK2.stl. Print all other parts from the original design on...

I upgraded to larger wedges since I've been using rubber feet underneath my MK2s.

Unfortunately, you'll need to modify the firmware to accommodate a taller hotend or you'll encounter problems during XYZ calibration: https://github.com/prusa3d/Prusa-Firmware/issues/205 Primarily, you must reduce the Z max height in firmware by...

I would not recommend anyone to use a loose-fitting protector since if it falls off it will probably do more harm than good. Print Settings Printer Brand: Prusa Printer: i3 MK2SRafts: No Supports: NoResolution: 0.1 Infill: 100% Notes: Print in...

Print Settings Printer Brand: Prusa Printer: i3 MK2SRafts: No Supports: NoResolution: 0.1 Infill: 100% Notes: Print in ABS or other high-temp material since it's close to the hot end. Post-Printing Clean the threads I ran a M8 thread tap through...

Little help for those who own the Original Prusa MK2 or MK2S. If you're looking to create a closed system that transmits filaments through a Teflon tube into the extruder from a box, I've got you covered. I built an adapter on top of which fits the...

Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0,15 Notes: To be printed upright. Good retraction settings are a nice thing to have for this as the supports make it retract a lot. ... Category: 3D Printer Parts

Also, it has 12mm wide "arms" rather than 10mm which is the widest it can be without interferring with the P.I.N.D.A probe and the outlets has been moved a bit away from the hotend to allow clearance for a silicone sock. The wider "arms" may lower...

You then should have enough space in the middle of the belt to push in a 15 to 20mm piece of filament to lock the belt. Yes, it looks a bit strange, but trust me, this holds a lot of weight. I wondered why no one ever came up with this idea. .)...

Here's a replacement for the original text: I created a custom nozzle for my Volcano Heatblock MK2S as there was no suitable option available online.\r\n\r\nTo set up the Volcano Heatblock, simply swap out the standard heat block with the new one and...

Clamping system for clamping stiff filaments to the frame of the prusa i3 mk2 printer Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No Resolution: 0.15 Infill: 20%

Clamping mechanism secures rigid fibers firmly onto the Prusa I3 MK2 3D printer's framework.

These stabilizers are specifically designed for my setup, which involves using full-size vibration dampers and retaining the felt feet that come with the MK2S printer. In my experience, there have been no problems using the vibration dampers in...

...... Visit www.ikea.com/us/en/catalog/products/20169658 for more information about this product. This is a revised version of the original Prusa design found at https://github.com/prusa3d/Original-Prusa-i3/blob/MK2/Printed-Parts/scad/z-axis-bottom.scad

I built this thing to center my raspberry pi camera, which fits perfectly on my i3 mk2s. It may also fit other versions of the printer. If anyone wants me to test the new mk3, I'd be happy to give it a try! Before starting this project, I used the...

Tool Holder Mounting Station: A Customized Accessory for Prusa Kit Essentials The Tool Holder Mounting Station is specifically designed to securely store Allen wrenches and needle-nose pliers that come with the Prusa kit, keeping them within easy...

Wanted to give remixing a shot and creating custom toppers for Prusa i3 MK3 printers. Added scaled down models to BobaMaker's Prusa_Topper_Blank.stl. All three turned out great the first time I tried printing them, so they're good to go. I recommend...

As many Prusa MK3 owners experience X belt bending issues with the original pulley, I created a remix for F623ZZ bushing using this design: https://www.thingiverse.com/thing:2763870. ...The design was originally made for 623ZZ bearings, but since I have...

Prusa-i3Mk2-x-Carrage-10mmBelt And another original Prusa part. I had to extend the towers where the belt runs around as well as some other areas. On this part, you can use the original screws; nothing else required. One detail: Because of the...

... on concrete panels; without this modification, the LCD would sit lower than the feet of the printer. The image showing two brackets depicts the original Prusa bracket (orange) and the PLA test print of the new bracket prior to printing in ABS.

The original parts were made for 1kg Prusa PLA which has a 50.35mm internal diameter on the spool, I'll add to this post as I buy more filament with different spool sizes in the future. This of course requires you to provide your own ball bearing,...

This collection of Z-axis parts solves the 0.2mm misalignment issue found in the original models (refer to https://github.com/prusa3d/Original-Prusa-i3/issues/34) and is designed for use with a F688 bearing, perfect for anti-wobbling applications. ...