prusa mk2 y carriage 3d models

... and I even believed it could lead to some layer shifts. Rather than completely rethinking the X-carriage as I had previously done (https://www.thingiverse.com/thing:3145981), I designed two spacers that can be added for a snug fit of the bearings.

Remixed from drodfro design to install on the Zaribo MK2.5 model, following his detailed guide available at https://www.thingiverse.com/thing:3245861. ...This version is specifically designed for use with my BMG extruder revision, which addresses...

X OFFSET = +18 Y OFFSET = -41.5 DECALAGE E0/E1 = 36mm The cooling tubes for parts are fixed, all that's left is to screw in the fans. There's also an optional support for BL TOUCH. I recommend printing it alone without support and gluing it with...

Remixed from drodfro design, this installation is specifically tailored for the ***Zaribo MK2.5***. Follow his detailed guide at https://www.thingiverse.com/thing:3245861 to ensure a seamless setup. ...Note that this installation is exclusively...

a combination of NSTT extruder with some mods, a servo probe bfpt like, we use to have this model on several prusa bear builds

Prusa MK2 and MK2S Upgraded Power Supply Unit Y-Axis Component Created by Evanrude is Distributed Under the Permissive Creative Commons - Attribution License Version 3.0. ...http://creativecommons.org/licenses/by/3.0/ Original Design Based on Josef...

Y Axis remake for use with bearing mount All parts are based on original Prusa i3 MK2 design. Print instructionsy idler requires support. y corners have support build into design. BOM: 4x LM8UU M3 nuts and bolts

Recommended bearing mount with same bed offset as SMA:http://www.thingiverse.com/thing:710913 All parts are based on original Prusa i3 mk2 design. PS: Look into Prusa i3 MK2S upgrade before deciding to modify your printer use this thing. Print...

This is a brand new y-motor holder designed specifically for the Prusa i3 mk2 printer. You can now easily mount your Astrosyn Dampener on it: http://www.ultibots.com/nema-17-damper-astrosyn-my17rmdamp/. Enjoy! Print Settings: Printer Brand: RepRap...

It enables using NEMA shock absorber on the Y-axis of the Prusa I3 MK2 and provides significantly more strength in the holding rods. I obtained my dampers from here:...

Standard Y-motor mount of Prusa i3 MK2 suffers from two problems: Only two screw points prevent NEMA17 damper installation; The mount is flimsy; after some days, the motor bends slightly and causes belt slippage over pulley borders (see photo). This...

This was also remixed from the "Rambo-heatbed-cable-clip.stl" file for the "Original Prusa i3 MK2S -> MK2.5 upgrade" on this page: https://www.prusa3d.com/prusa-i3-printable-parts/ It's also worth noting that I used the following parts to connect...

This modification of the original Prusa i3 MK2 power supply "Y" bracket allows for attachment after assembly, eliminating the need for disassembly and utilizing only parts from the spares kit. Licensed under the GNU GLP v3 license as the original...

A custom Y-Axis bearing mount for the Reprap Prusa i3 MK2 printer is being shared after the original mounts broke, requiring new ones to be printed. This design is exclusive to this specific 3D printer model and may not work on other printers. Two...

The belt holder assembly was also shortened in length to fit within standard Prusa i3 MK2 configurations, avoiding interference from both the motor at one end and the belt holder at the other. ...When installing this part, the adjustment screw should be...

Additional design enhancements include: - A 35mm longer camera_holder.stl for added functionality - y_holder.stl, which is tighter to the printbed aluminium frame for improved stability Printer Settings: - Printer Brand: Prusa - Printer Model: Prusa...

This is a remix of the Rambo Y-Axis mount from https://www.thingiverse.com/thing:398515 This mount will connect up to the Rambo cover that is used in the Prusa 2.5 upgrade kit. This was also remixed from the "Rambo-heatbed-cable-clip.stl" file for...

// - Mount the right bearing snug but not tight to the bed carriage // - Mount bed carriage with rods on Prusa, adjust width and skew of threaded rods until the right rod is perfectly parallel to the left. When parallel, the bed moves without belt...

New Build Remake for Enhanced Performance Based on Original Prusa I3 MK2 Design Excellence SMA and Bearing Mount Options Available Now

I found that they work well on Prusa i3 MK2/MK2S (and clones) y-axis systems. Personally, I tested T2 and T3, and I prefer using T3. I'll give a try to T4 because I think it gives me a better outcome. There are three different bearings with IDs...

For my second Prusa i3 MK2 build, I chose to use an industrial-grade NEMA damper/decoupler, available on eBay (DE): https://goo.gl/6nvFga Unfortunately, the original Y-axis stepper motor mounting plate only secures the stepper at two vertically...

This is a Y-belt idler and tensioner designed for the Prusa i3 MK2 and MK1 printers. It's likely compatible with other 3D printers as well. To assemble this idler/tensioner, you'll need one M3 screw, an M3 square nut (which came with your original...

Custom Anet A8, Prusa Mk2S Y Carriage 220x220x5mm

X-Carriage compatible with the MK2.5(S) Bondtech Prusa Extruder with the Revised X-axis https://www.bondtech.se/en/product-category/upgrade-kits/prusa/ and https://www.thingiverse.com/thing:3559732 This X-Carriage is designed to work exclusively with...

Aaron also made a remix of this design: https://www.tinkercad.com/users/7Z01p6EVg8r-aaron-yourk Print Settings: Printer: Original Prusa MK2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.3mm Infill: 20% Notes: Perimeter Shell is set to 5, and Top...

The Prusa i3 MK2 - Y-Frame Assembly Helper by MartinMajewski is a great tool, but what if your current printer isn't big enough to print it? One solution is to cut the design into four pieces and add flanges with holes that fit M3 machine screws. ...

These Prusa i3 Y carriage extensions allow mounting a RepRapPro heatbed insulator, featuring a preferred aluminium top surface, MK2 style PCB bed and MDF insulator setup. The insulator is secured via a three-point, spring-loaded mechanism for easier...

The request came through on the IRC platform for this specific topic.

People have been requesting that information from me on Internet Relay Chat.

While this works fine, a hex bolt would be easier to work with given the tight space near the front LCD screen on my MK2 Printer. ... Fortunately, Brukj has created an excellent PDF instructional document featuring the original file, which can be found...