prusa mk2 wiring diagram 3d models

I really liked mattshub's original prusa MK2.4 extruder, but i have a bl touch, not a pinda probe. ...Remixed his design to hold a BL touch.</p><p>correct height can be adjusted using washers ;)</p><p>BLtouch offset X:32 Y:12</p><p>NOTE: all other files...

I designed it specifically for the Prusa i3 MK2, which often struggles with visibility on first layers. The endoscope is securely fastened to the hotend fan using original screws, despite being a snug fit. ...To prevent any movement or slippage,...

Prusa i3 Mk2 P.I.N.D.A. probe protector hat for original device. Several existing models were tried, but none fit properly. This custom design is intended to perfectly accommodate the original PINDA with M8x1.0 thread. Calibration of Extrusion...

I specifically designed it for the Prusa i3 MK2, which has a notoriously difficult time visualizing the first layers. ...The holder is securely attached to the hotend fan using original screws, and despite being a snug fit, extra electrical tape was...

This modification of the Skelestruder for Prusa i3 mk2 was made because I have that printer and wanted to mount that extruder on it. STEP files for all models provided if you want to modify this further. Changes: 1) The x carriage was made a bit...

Print Settings Printer: Prusa i3 MK2 Rafts: No Supports: No Resolution: 0.15 Infill: 30% Notes: I chose a higher infill to help keep it from warping over time as it will be next to a heat source for most of its use, and I made it out of PLA. ...ABS...

It works fine and has been tested on a Prusa MK2; later models have not been tested, but they should work too. BOM --- * 4x dampers Type A M4 Ø 15 / H 15 (search eBay for Anti-Vibration-Mount M4 or Schwingungsdämpfer M4) * 4x M4 nuts * 4x M4 washers...

Print Settings: Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: Yes Resolution: .20 Infill: 20% Notes: The STL file should already be aligned the way it should be printed. Recommended first layer is the logo side down. ...

This is a modified Original Prusa MK2 fan nozzle shroud. The original fan nozzle did not fit well and also directed too much cooling toward the heated nozzle. This resulted in THERMAL RUNAWAY and lowering of the hot end temperature during...

Print Settings Printer: Prusa I3 MK2 Rafts: No Supports: No Resolution: 0.200 Infill: 40% Notes: Customize the words on the front of the LCD by modifying them in FreeCAD's interface. Export the modified part as an STL file and then print it. How I...

This is an updated remix of dima_leigr's v1.2 Hemera adaptor for the Prusa MK3S, modified to reach the MK2.5S limit switch when homing the X axis. *Notes for Prusa firmware* A "variants" file for firmware 3.8.1 is included with the updated probe...

Here's an update on the design changes: * v8 - moved the nut to the opposite end * v7 - first release Print Settings: Printer: Original Prusa i3 MK2 Rafts: No rafts needed Supports: No supports required Resolution: .2mm resolution Infill: 50% infill...

at the moment just messing trying to get several things to mesh together..mk2 done with a 5mm spacer on the hotend fan duct I think this will now fit printing a test piece now and i have a 40x40x20 high output silent fan to go on it.OK this is...

I created a c170 holder previously for my prusa i3 mk2 but was no longer satisfied with it. After taking a closer look at the machine, I discovered that the front screws holding the heat bed in place do not extend through the hole in the frame,...

Somehow the vibration damper from https://www.thingiverse.com/thing:1707045 didn't fit snugly around the feet of my Prusa I3 MK2, so I drew a simple damper which fits loosely on the feet. It does an awesome job dampening the sound. When I run my...

This is a filament guide upgrade for the Prusa i3 Mk2 printer. A full roll of filament often falls off the sides when the print head reaches its maximum height and is positioned near one side or the other. The original clip-on guide attaches to the...

Somehow the vibration damper from https://www.thingiverse.com/thing:1707045 didn't fit snugly around the feet of the Prusa I3 MK2, so I drew a simple damper which has a bit large fit for the feet. They do an awesome job dampening the sound. When I...

Loved this design but it didn't fit with my Prusa i3 MK2 so I modified the design a tad. My setup is a bit different so I changed it to be specific to my setup. However, if anyone has a similar setup I'm glad to share my remix. Great design, makes me...

Print Settings Printer: Prusa i3 Mk2 Rafts: No Supports: No Resolution: .2 Infill: 20% Notes: With no supports needed, the tube prints vertically without any issues. The bottom bearing stop is chamfered for a smooth transition, eliminating the need...

This is a custom-fabricated replacement for the Original Prusa MK2 fan nozzle shroud. The stock fan nozzle failed to fit snugly and also directed an excessive amount of cooling airflow toward the heated nozzle, leading to a dangerous thermal runaway...

This is a modified Original Prusa MK2 fan nozzle shroud. The original fan nozzle did not fit well and also directed too much cooling towards the heated nozzle, which resulted in thermal runaway and a lowering of the hot end temperature during...

I utilized it to dampen my Prusa i3 MK2, but I quickly realized that the unsymmetrical weight distribution of the printer wasn't compatible with the one type of damper. Because the printer is heavier in the back, we need stiffer springs there and...

Hi all, This is my personal take on the Geeetech Prusa I3X acrylic, dubbed MK2. I utilized some parts sourced from Thingiverse and adapted them to suit my needs. Other components were designed by me. The Z carriage was borrowed from this design:...

... 65% outline overlap. Print Settings: Printer: Prusa i3 mk2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill: Minimum 30-40% rectilinear Notes: Use minimum 65% outline overlap so the cylinders attach tightly to the horizontal holder.

I encountered an issue with my Mk2 while utilizing the full bed, where the cables frequently collided with the printing surface, prompting me to devise a temporary solution until I could implement more permanent modifications involving chain...

I absolutely loved the standard spool holders that came with the Prusa i3 MK2 so decided to spice up the functionality and make it a bit more aesthetically pleasing with a crossbar to hold the filament. All spool sizes should be compatible. I wanted...

This is an upgraded version of my previous design, which now includes a more steady base, an "open layer" addition and a print-in-place top with handle. The tower is meant as a method of recycling Prusament spools, but can also be made by printing...

This is a spin-off of my MK2-X with enclosure design. http://www.thingiverse.com/thing:2252428 The first step will be enclosure assembly, so just uploading the assembly files for simplicity and file weight. For now, there is only the SketchUp file. I...

Users install MK2 and MK2s damping feet using 35mm Adhesive felt pads, widely available at hardware stores for a mere 0.40eur per bag of 8pcs; 12pcs are required for the 6 feet. Two central pieces are needed, along with four front and rear pieces.

This is a spin-off of my MK2-X with enclosure design. http://www.thingiverse.com/thing:2252428 The first step will be enclosure assembly, so just uploading the assembly files for simplicity and file weight. For now, there is only the SketchUp file. I...