prusa mini mods 3d models

Another for the Prusa Mini Y Axis Motor.Use a Neodymium Round Cylinder Magnet 8X3mm (Amazon). ...It's a tight push fit which does bulge out the body a tiny bit, but will fit with some filing on the part that goes into the motor housing.Print...

Also, please note, that before packing and shipping the printer for repair, this add-on has to be fully uninstalled. Material: a combination of Prusament PETG Prusa Orange and Prusament PETG Jet Black. Total weight: 708 gTotal printing...

The LCD case is made from 5 files:Case: RepRaptor_Prusa_mini_LCDcase_Frontprinted in PETG Prusament blue marine 15% infill 0.2mm2. RepRaptor_Prusa_mini_LCDcase_Middleprinted in PETG REAL transparent blue 15% infill 0.2mm3.

This is my version of the Prusa Mini. I tried to make an overall smooth design with integrated filament sensor, E3D V6 and without any visible wires. My Prusa Mini Clone was not cheaper than the original I just designed it for fun. The inner parts of...

So I found some models of the MINI online and used that to create this independent, mobile screen stand for your MINI!It uses a very similar geometry as the original mounting point on the MINI, as I used it a reference to create this.For this print...

The depth of the insert is 0.8mm This has 2 STL files: prusa mini leveler.stl : This file should be adjusted to accommodate all corners except for the rear right prusa mini rear right leveler.stl : This file should be adjusted to accommodate the...

The depth of the insert is 0.8mm This has 2 STL files: * **prusa mini leveler.stl** : This file should be adjusted to accommodate all corners except for the rear right * **prusa mini rear right leveler.stl** : This file should be adjusted to...

USB holder for Prusa Mini Print instructionsUSB holder for Prusa Mini ..my remix from https://www.prusaprinters.org/cs/prints/15544 needed M4, T-nut, USB 3 cable angle Bend Up, 25-30cm, ex. https://www.aliexpress.com/item/4000975142956.html...

... So to fix this annoyance I made this simple spool holder. It uses the 3 of the longer screws and 3 nuts that come with the prusa mini spool holder. ...If you have the screws and nuts it should also work as a spool holder for a different printer.

Lock bottom of the holder into Z extrusion and fix it in place with T-nut and bolt.Printable M3 nut can be found here: https://www.prusaprinters.org/prints/96135-prusa-mini-t-nutSupport meIf you like this design and want to support me, you can buy me...

I made this because of poor stability on foam feet. Print 3x prusa_mini_damper_feet_3x.stl Print 1x prusa_mini_damper_feet_back_1x.stl Print 1x 5th_feet_Z_support.stl Use M5 screws to fit it in profiles. And I used this silentblocks as feet:...

To clarify, I have included a markdown file titled Calibration Method.md which outlines the process I used to calibrate my printer back to square form.\r\n\r\nThis information is also available on GitHub at https://github.com/pgooch/Prusa-Mini-Shims...

... use a 500 mA USB plug, as anything higher may cause the lamp to overheat. To secure the lamp to the holder on my Prusa Mini, I used a 5x12 screw and an M5 T-nut. ...Additionally, I applied some 3M double-sided tape to keep the lamp firmly in place.

Prusa Mini Spool Holder Assembly Two bearings, each with a diameter of 8mm and a width of 3mm, are required for the Prusa Mini spool holder assembly. A M8 thread rod measuring 140mm in length is also needed. This rod will be used to secure the spool...

Print information for Knob:Printer:  Prusa-MiniFilament: Prusament PETG Galaxy blackNozzle: Bondtech 0.4Layer high: 0.15Infill: 30% gridRafts: No Supports: No  Print information Housing:Printer:  Prusa-MiniFilament: Prusament...

I designed this Prusa Mini Light Bar to work with existing led strips I had laying around. I tried to match the same prusa hex theme the Mini Base uses as well as my camera mount. I'm very happy with it as it does a great job of...

I needed something to neatly mount the power supply, so I designed this simple Power Supply holder for the Prusa Mini. This allows you to vertically mount the PSU. There is a large opening at the bottom for the power-cord to pass though. I mounted it...

This is a dust cover for a prusa mini. Yes you can print it on the mini you just need to turn it 45 degrees. For the metal section I just bent a 2 pieces of one of those wire hangars into L shapes and used a rubber band for extra springiness. ... ...

To create a compact printer, I shrank the Prusa i3 to fit within a 100x100x100mm volume and reduced its footprint. The mini-i3's dimensions are approximately 250x280x270mm, constructed from a 6mm aluminium frame. Purchase suitable heatbeds...

I acquired a Prusa Mini primarily to accommodate its compact design, which enables me to easily transport it during my travels. ...To prevent the mechanisms from shifting around in the vehicle, I created custom locking devices for each of the three...

A small and simple tool holder for Prusa MINI which is mounted to the Z-axis. I use it for tweezers etc. It has an additional peg to hook bigger items such as spatula. ...Requires two additional M3 bolts and T-nuts like these...

A sturdy yet straightforward filament holder designed specifically for the Prusa Mini. This accessory attaches to the top of the vertical 3030 beam via T-slot nuts, providing a robust base for spool support. ...A 1/4" steel rod serves as the axis for...

Bigger version of the Tiny Toolholder for Prusa Mini. Snaps into place on top. Shouldn't interfere with the z-axis cables, but be careful. ...Should fit a bunch more of your “always needed” stuff, like pliers and glue or whatever.</p>

LCD Cover for the Original Prusa Mini safeguards the screen when you're not using the printer and conceals the light at night to ensure a restful sleep in the same room. ...Simply print it in any desired material or color, provided that it's opaque.

Mini version of my primary 3D printer, the Prusa I3 MK2. Ideal for: Creating custom Christmas decorations Designing a unique desk accessory Crafting a decorative shelf item Conducting a benchmark test to optimize performance Building a small-scale...

LED bar for the Prusa Mini which can be put on top of the Z-axis.The LED strip is battery powered and controlled by a RF controller.The 2 parts can be mounted together with 2x M3x12 bolts with nut The LED strip with controller can be found at:LED...

This is a tray design for the Prusa Mini. It can the fixed on the Z axis (vertical aluminum profile) with a T-nut. ... Very useful to hang various tools, and to hold small parts on the tray To make it even more cool, try make the bottom of the...

Prusa Mini spool holder Bearings 608 2pcs Thread rod M8 140mm Screw M5x12 2pcs Nut M5 3030 2pcs From https://www.thingiverse.com/thing:2350134 .

I bought a Prusa Mini specifically for its small footprint so I could bring it with me when I travel. ...To keep the mechanisms from moving around in the car I have designed transport locks for all three axes.</p> <h3>Print instructions</h3><p>The Z...

Holder for AC/DC adapter for 3D printer PRUSA MINImontage on desk, board, table, wall etc.Print instructionsnote. attached gcode = 2x holder</p><p>NOTE: !!! ...<strong>This holder is for old AC/DC adapter PrusaMini</strong></p>