prusa mini enclosure 3d models

I modified the magnetic handles and base for Dominik Císař's Prusa enclosure (https://www.thingiverse.com/thing:2864118) as well as JesusFreke's redesigned handles (https://www.thingiverse.com/thing:2922505). I discovered that using 1/2" x 1/16"...

Here is a modular PRUSA Enclosure organizer tray system. I designed it to fit snugly around the front of the PRUSA MK4 and organize my tools and printing accessories. It keeps things organized and out of the paths (within reason of course) of the...

So I found some models of the MINI online and used that to create this independent, mobile screen stand for your MINI!It uses a very similar geometry as the original mounting point on the MINI, as I used it a reference to create this.For this print...

They only work in combination with https://www.prusaprinters.org/prints/57890-prusa-lack-enclosure-adding-massit has to reach over the additional plate.Print SettingsPrinter...

These brackets were designed to secure a 3-stack tall Prusa Lack Enclosure to a wall with a 150mm offset from the wall to allow the top to open. 2 sets of brackets (as pictured) are intended for optimal rigidity. They made a big difference in...

After few months of using, I decided that sometimes I want to use 3D printer as basic MK3S+ so i designed this filament guide to easily use enclosure as built before.I made few evolutions of my model. So, I decided to upload all of them. Best for use...

Update March 19, 2022: Improved Prusa LACK Enclosure Levelling Feet are now available!  I strongly recommend checking out this new version, as it features some improvements that make post-installation level adjustments far easier.----------I...

I was inspired to create this model to prevent this inconvenience for others!The Prusa MINI is an amazing machine, but it comes with a bit of a concerning extruder design that leaves the hotend fully exposed to anyone whose fingers may fail them.I...

Needed a way to hold two USB extension cables…One is from the printer's memory stick slot, the other is from the computer.I don't like plugging the USB stick in and out of the printer directly (so as not to wear out the port) it's much cheaper to...

Creating the [Prusa Lack enclosure](https://www.thingiverse.com/thing:2864118) I ran into various issues. One of them is that I could not find 3mm thick plexiglass. Was hoping that the fitting would still be snug enough to hold the plexi. To...

Creating the Prusa Lack enclosure (https://www.thingiverse.com/thing:2864118) I ran into various issues. One of them is that I could not find 3mm thick plexiglass. Was hoping that the fitting would still be snug enough to hold the plexi. To solve...

 Enough enclosure height to put the filament on the printer inside the enclosure.Slide-in front doors. If you print PLA or PETG in a warm season, you can slide in the front doors to the side.LED lights; the switch is on the front panel.  Prusa PSU...

I wanted a very compact and simple webcam mount for my Logitech C920 with a standard ¼ inch thread to attach to one corner of the Original Prusa Enclosure.On one side, it has a 2.8mm hole to attach with an M3x8 screw (use one of the spares that come...

Hi all, I decided to built the Lack Enclosure for the PRUSA MK3S+ described by: https://www.thingiverse.com/thing:2864118, https://blog.prusaprinters.org/cheap-simple-3d-printer-enclosure_7785/ In general they did some good work, however in my...

Top supports for an enclosure i am creating for the 3d Printer

mount for prpus enclosure. ...I edited bottom corners and i add 100mm for oiginal corners.

... control board. Can be printed without supports in proper orientation. Magnet slots included if enclosure uses non-rigid enclosure plastic/fabric and want to make a ring to “clamp” enclosure surround. ...Vents work for a 24" side to side enclosure.

Credits to cisardom for thing https://www.thingiverse.com/thing:2864118 and Mikolas Zuza for the guide https://blog.prusaprinters.org/cheap-simple-3d-printer-enclosure/ I was a bit unhappy with the final build because cutting the plexi to 440 x 440mm...

These are larger versions of the cable passthrough tube used for mounting the power supply and/or LCD controller outside of the Prusa LACK Enclosure V2. _lack_cablepassthrough provides enough room for the power cables as well as a USB cable for...

a 15mm spacer to add space on the ikea lack printer enclosure leg ends. ...helpful if you bought the wrong size acrylic or need to add height to the enclosure.

Prusa changed the display bracket on the Mini+ and I modified the original Prusa Mini USB mod to reflect that change. 

In an effort to make the Prusa Enclosure less deep I mounted the PSU to the side instead of the back.If you want to do this I feel obliged to say that, minor as it may be, this causes irreversable damage. Namely a hoop for a tie wrap on the metal...

I loved the original heatbed cover and wanted to stick with it after the replacement. I had to use the enclosure after installing the original heatbed cable cover, therefore I designed a flanged cable cover to be mounted on a cutout in the acrylic...

To see how this looks on your printer, check out these videos: https://www.instagram.com/p/B2VuI-Bjjf9/?utm_source=ig_web_button_share_sheet https://www.instagram.com/p/B2Zv7HuHQco/?utm_source=ig_web_button_share_sheet I wanted to build lightbar...

Removed all stabilization material visible in the cut window, but leave the floor unharmed. Remove the most top table from your printer enclosure tower and place the cut table directly on the other table. Put a 40x40 cm concrete platter inside the...

This tool holder will be mounted onto the MK4 enclosure to hold a snip, brush, scraper and small parts within a basket.

Control airflow within the enclosure to ensure optimal performance. ...Include the following hardware: Six (6) M3 screws Six (6) M4 screws Six (6) M4 nuts

This printer enclosure is fabricated using Solidworks software. ...It's produced by printing with Colorfabb nGen material, featuring a 0.3 millimeter layer height and three parameters.

I needed a place to put my spare build plates and had no room on my table. ...So this model mounts right on the side on the enclosure. 2 M3 screws work great at securing it to the enclosure. ...Prints in about an hour!

All the other side mount curently on the web have the LCD on the right side; these ones won't allow you to extend the PSU outside the enclosure.If you have detached the PSU, please remember to add the brace in place of the PSU...