prusa layer shift 3d models

If they refuse to go in, do not force but check if you have missed to remove some grates.Removing the support socket from the exhaustAlthough the connecting ring is only "one wall layer" thick, it was holding up pretty strong on my test print. ...You...

PC\ABS costs the same, but it is more difficult for them to print and it is not much superior to conventional ABS in terms of layer sintering. Plus, this filament is quite heavy, its density seems to be even higher than that of a PLA. In addition,...

The parameters with which the pieces were printed in my case were: low quality profile with layer height of 0.28mm, 10% cubic infill and support for the pieces and adhesion Raft was used (see picture above for more details).The material used for...

The hubs can be reused!Filament usageFor a spool with 80 mm axle diameter, structural size of 8 mm, printed with 15% infill, no rafts and no supports:Hub:23 gSpoke:9 gLabel:12 g  Total for spool with two hubs with standoff, three spokes and...

The spring design skips a layer so it shouldn't be too hard to free up (also why resolution of .2 is recommended) Parts will need to be re-oriented. I recommend printing shells and the core bottom up (threads last). The base can be printed right side...

I was scared to over tighten it because at some point that would cause the layers to split unnecessarily. So I was able to run it for about 6 minutes with hot water and a negligible/acceptable amount of water was leaking out and spraying back towards...

I have included some sacrificial layers in some of the holes in the mounts which will need cleaning in addition to the supports. 2.The WM Upstand and Clips will require either a very slow print speed or a raft due to their small footprint. 3.It is...

-100% zero overhang -basically no layer perimeter rough surface issue. -100% infilled so no hollow spaces. -just 8.5mm very low Z height, so perfect for any flexible printing. (Usually got a rough finish when printing up to a 15mm Z height.). ...

To achieve the best effect, use a large nozzle with large layer height and line width. The hair is the most difficult to print. If you want a nice surface you need to print it in the orientation as it is designed, but that requires a lot of supports....

This tube has only been tested on a "Nikon F" film camera (1959), please verify that the printed mount does not collide with any new mount features introduced in newer electronic cameras.If you like macro photography then check out my other designs...

Simple bricks to play with or to integrate into other projects, designed to be easy to print, and easy to integrate in all other projects.Printing parameters:PLA//0.4 nozzle//0.2 layer height//0%infill//no support//brim All the parts in the files are...

We will need to adjust the z offset from home via GCODE as there is a small amount of flex required to trigger the sensor and left uncorrected the nozzle will be pressed against the bed for the first layer. However, that requires some tinkering and I...

Fire retardant filament is NOT necessaryALL Parts are printed without any supports!Perimeters: 4, solid layers: 5 for both top and bottom, Infill: 40%All STL's already have correct orientation for print, just import in the slicer of...

with three side walls and four layers for top and bottom. Use all methods to avoid warpage. Figure around 36 hours of print time for a full dash. I have successfully printed in ASA with no fiber with each dash panel broken into two pieces on a...

This game is similar to the board game China Town in play style, please see below or the attached rules for more detail about how to play the game. Players: 4-5Time: 60-120 minutesComplexity: 2/5 Non printed components required:5 - regular...

All clothing sets include many full layers - you can strip the character down to his underwear. Fully customized combinations of character. Just use one of the prepared prefabs by dragging and dropping it onto the stage! The female characters have a...

300x300 mm² sticky pads that hold on to the vinyl)20 mm rubber band or the printed spring2x M3x8 hexagon socket head cap screw2x Ruthex RX-M3x5.7 threaded insertsPrint SettingsPrint all models in their provided orientation with 0.4 mm nozzle, 0.2 mm...

You're using this model at your own risk etc.Print settings / orientationI recommend slicing with PrusaSlicer 2.5.0 (currently in alpha).0.20mm layer height, 15% infill.PLA has worked great for me, try finding a color that has minimal...

The end mill caught me by surprise and drew blood.Print instructionsI made the body in PETG, .2mm layer height, 3 perimeters, with 40% infill. Clamp printed at same settings but 100% infill. ...You don't need any supports if you orient things correctly...

If you can't slide the Arm over the Mounting Plate file, remove some material from the Mounting Plate using sandpaper or a file until the parts fit together nicely.SettingsMaterial: Anything you want (compensate for shrinkage if necessary)Extrusion...

This is used to connect tip of the fingers to the servo arm.-elastic band, stronger is better if you can get your hands on it, but double or triple layer weak is enough also. This will be used to re-bounce fingers open when hold is toggled...

The AMS colour changes work effortlessly, and I am able to start a print with the external spool in a matter of seconds.Print SettingsMaterial: PETG (optimal) - PLA (best) Layer height: 0.08mm (optimal) - 0.12mm (best)Walls: 4 (highly...

This safe is secured by a 3 digit combination to prevent anyone from opening it (unless they have a hammer or a heat gun, I mean it's just plastic at the end) This is kind of a long build but it is perfect to learn how a combination safe...

By layering the filters 3 deep, you'll prevent blue/UV leakage that can mess up the colors of the photos it takes. Install the thermal camera next to the NoIR camera. Wire the switch in series with the DIY USB connector. Ideally the ground...

 UPDATE 07.04.2024: Added a separate printed back surface for duo ton setups, its of course optional but looks so damn good :D  after gluing it on use a Stanley knife to take off the edge in multiple steps until the transition of the layers become...

All parts use a 0.4 mm nozzle, PLA/PLA+ and a 0.2 mm layer height. Parts List Brett OliverParts by Brett Oliver Part...

If it's too tight you can try to reduce the width at 98% (or lower) but you must not reduce the lenght.The “Boat clip” has a very small first layer. Maybe you should print it alone not to fail the all plate of pales if it...

I printed most of it with a layer height of 0.2mm and 20% infill. Some Parts need Support. Have fun printing and driving Dies ist ein fast komplett gedrucktes 1967 F1 RC Auto im Maßstab 1:8, dass ich an einem 1967 Eagle angelehnt...

So a very good inter-layer adhesion will help making the mechanical behavour of your parts more omnidirectional. Can you do that with PLA?¿? If you do, remember not expose the chassis in the sun and heat for hours and monitor and control temp of your...

Do not try to use any “hard” filament like PLA or PETG - you would not be able to slide the tire onto the rim.My recommended basic settings are:Wall thickness: One single perimeter of about 0.7 mmLayer height: 0.15 mmNo supports!Infill: 10 to 12% of...