prusa lack enclosure v2 3d models

This model uses the basis of the original handle model from the Prusa MK3S IKEA Lack enclosure and complements the ability to change the handle design using the standard 1/4 thread.The base of the handle is prepared in files in two variants - for a...

My very first design in fusion 360 ( steap learning curve) part may need some tweaking but very proud if my first result. So i designed a simple sliding drawer frame to go under a Lack table (enclosure: https://www.thingiverse.com/thing:2864118 ) For...

... smaller magnets which are easier to buy of the internet. ...also slide in from the side. Also made the acrylic glas inserts 0.2mm thinner so 3mm glas fits in tight. Print instructionsUnassociated tags: lack enclosure Category: 3D Printer Accessories

I'm adding another Lack Table to my enclosure tower for the spool holders of my MMU2S. I don't need extra space, so I'll shorten the legs from the additional table. This will help stack them again as they're hollow. ...I've printed the files, updated...

This is a top-mounted door handle magnetic kit specifically designed for the IKEA Lack enclosure used in Prusa (and other) printers. There are likely many similar kits available, but I created this one due to two key reasons. First and foremost, I...

****************************************************************** Original: precise filament guide for IKEA LACK enclosure. Filament is guided by double rolls on ball bearings. Needed: 8x ball bearing 624ZZ or 624 2RS 8x countersunk M4x16 DIN...

Designed to be mounted to the Lack table with two of the same 6x20mm screws used to build the enclosure!I recommend printing the part in PETG since it will be inside the enclosure. The part in the cover photo was printed with 0.2mm layer height and...

Spool holder mount on the PSU bracket that replaces the original PSU on MK3 for the lack table enclosure. I wanted to avoid having the spool sitting atop the table, so it's positioned on the right-hand side, inside the enclosure with a 45-degree...

This is my initial draft of an LCD holder for the Prusa i3 MK3S without an enclosure. ...To assemble this, you will need to purchase two panhead screws with a length of 5mm and a diameter of 20mm, as well as one countersunk screw with a length of 3mm...

......Primarily, the hole for cable connection to the electronic enclosure was relocated on the opposite wall, and the ON/OFF switch was elevated (or lowered, depending on perspective). ...The markings and triangles were eliminated (commented out in scad).

The new black PSU of the MK3S has a width of 106 mm, not 100 mm like the old one. So the PSU holder of the lack enclosure doesn't fit anymore. I've created a new one, similar to the original, but with a small knob to fix the PSU on the top. I've used...

This is a Re-Remix of the [Ender 3 resized original Prusa i3 MK3 enclosure](https://www.thingiverse.com/thing:3598219) to fit the Ender 5. The spacers have been resized to 150mm each so they will give you an additional clearance of 300mm. Overall...

As a result, the original PSU holder within the Prusa enclosure is no longer compatible with this new component. To resolve this issue, I have engineered a custom PSU holder that closely resembles its predecessor but features an added twist: a small...

Because I wanted more space for the MMU2 that's due to arrive soon, I decided to enlarge the Lack enclosure to 600mm instead of its original size of 440mm. I proceeded to extrude new parts and drill holes in the bottom components since they were...

I wanted to install a secondary tier of storage compartments within my printer enclosure, thereby increasing available space for storing supplies and materials, but I've decided not to enclose it in plexiglass. These identical models from Prusa are...

The very simple feet are there to raise my lack up slightly as the screen is a few millimetres too high if mounted on a table (my lack enclosure is a cube on the table). I printed them in PETG and noise has increased so I may switch to TPU. I have...

Looking for long hinges variants, those long hinges available were all exceeding the buildplate size for the Prusa MINI/MINI+ These are about 165mm long. 3mf included with recommended settings Note, the one I have taken a photo of in the shot is...

Looking for long hinges variants, those long hinges available were all exceeding the buildplate size for the Prusa MINI/MINI+ These are about 165mm long. 3mf included with recommended settings Note, the one I have taken a photo of in the shot is...

... the one I have taken a photo of in the shot is actually 1cm shorter at 155mm (my V1 print). V2 that I've uploaded here is 165mm long.Recommended Print Settings:BrimPrint uprightAny infill will doPerimeters: 3Support from build plate

Original Model: https://www.thingiverse.com/thing:3926452A quick remix of DD123456's MK3S holder with 6mm screw holes compatible with the #12 screws recommended by Prusa in their v1 enclosure guide. Thanks again to them.</p><p>The other two holes for...

Here is a quick remix of DD123456's MK3S holder, adapted with 6mm screw holes that are compatible with the #12 screws recommended by Prusa in their v1 enclosure guide. Many thanks to them again for their guidance. The other two m3 screw holes were...

Easy and fast Ikea Lack Enclosure for your 3D Printer. It fits 50cmx50cmx 0,2cm Acrylic glass on three sides Backside is a 61cmx55cmx0.5-1.5cm woodplank you can fit 2 120mm Fans in the backside when cutting out the holes (Advise: 1 Intake Down, 1...

Easy and fast Ikea Lack Enclosure for your 3D Printer.It fits 50cmx50cmx 0,2cm Acrylic glass on three sidesBackside is a 61cmx55cmx0.5-1.5cm woodplankyou can fit 2 120mm Fans in the backside when cutting out the holes (Advise: 1 Intake Down, 1...

This is 30mm riser for upper part of legs to make the official enclosure compatible with taller ender 3.&nbsp;This riser it intented for those, who printed all the parts for the enclosure, but they cannot fit the ender 3 in it.

Habe keine Halterung für die linke Seite eines Ikea Lack Tisches gefunden. Habe selber eine erstellt. ...Viel Spaß beim drucken!</p> <h3>Print instructions</h3><p>Habe es mit 0,2mm Layer high gedruckt.</p> <p>Ohne Support.</p>

This remix makes it so the LCD controlbox sits 1.5mm higher to allow the LACK drawers to open (when also using the drawer spacers). Raising it by 1.5mm is enough to allow the drawers to open under the LCD controller, but still sits below the top of...

I created this model using Fusion 360 to fine-tune my enclosure for a tighter fit. The stock files were far from ideal, if you ask me. To import a STEP file into Fusion: File > New design from file > Select the STEP file from your computer and...

After experiencing repeated failures with the latch magnets' adhesive, I took decisive action by creating a compact enclosure component that securely holds the magnets in place between two precision-printed parts. ...To achieve this, I simply installed...

Original files here: https://blog.prusaprinters.org/cheap-simple-3d-printer-enclosure_7785/ I had trouble finding the exact size screw for the hinge corners, so I modified the design to fit the screws I had. This design adds a 5.5mm wide by 3.5mm...

This is a versatile mount designed to securely hold the thread of a universal spool holder, accessible at https://www.thingiverse.com/thing:767317. ...It can be easily attached to the top of an enclosure using M4 or 4mm screws/bolts.