prusa i3 raspberry pi 3d models

A Raspberry Pi holder that attaches to the Prusa's X axis stepper motor, for use in running OctoPrint. It's out of the way, and you can use short cables. It's is just a flat bottom for holding the Pi and does not wrap around to have walls with port...

... Noctua und LM2596 zur Spannungsminderung von 24V auf 5.1V. Noctua klickt in Position, also keine Schrauben nötig. On/Off Schalter für Mini und Raspberry Pi und Halterung für USB. Print instructionsBraucht Stützstrukturen unter der Noctua-Halterung.

The Octoprint case sits lower than in the original position. Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 15% Notes: Print with...

I upgraded my Prusa MK3S with a custom Raspberry Pi 4 case that includes several key features. The case boasts a convenient rocker switch, which allows me to easily turn on and off my printer. Additionally, it has a standard barrel jack that connects...

Blocks most GPIO pins of a Raspberry Pi board for connecting the Pi to the Prusa Einsy board via GPIO using the Prusa Pi-Zero W installation guide (https://help.prusa3d.com/en/article/raspberry-pi-zero-w-preparation-and-installation_2180). Power pins...

To begin with, I rotated the raspberry pi's usb ports downwards to improve accessibility and usability. Additionally, I incorporated a camera ribbon cable cutout to facilitate easier setup and integration. ...While I acknowledge the original designer's...

A case for mounting your Raspberry Pi 4 to the Prusa Mini. Made this to use with OctoPrint and a Raspberry Pi Camera. ...Designed to hold the Pi just behind the display on the Mini.Inspired by:Pi 4 Case by...

This is a custom-made camera holder for a Raspberry Pi, specifically designed for use with OctoPrint and featuring programmable LED lights. The LEDs are powered directly by the printer's PSU and are rated at 12 volts; I've installed three in my...

Simple yet effective case for mounting a Raspberry Pi 4B into the official Prusa Enclosures. Thank you to 'lazax' for the original case design! First, assemble the mount with the case bottom using two 3mm x 8 screws. Next, pop out one of the left...

Took 12v from the existing power supply for the fan, and then through a buck converter to get 5v for the Raspberry Pi. The next steps will be set up Octoprint so I can do wireless prints and watch it through a webcam! I've included the Fusion...

I needed a Raspberry Pi Bracket for the right side of my Prusa MK3S printer bed to work with the common Pi Camera Mount. I wanted to use the MK3's Extrusions to mount too so that my Pi Camera cable would line up properly and I would be able to use a...

This mount enables you to securely attach a Raspberry Pi v2 camera directly to the front right diagonal arm of the bed frame on your Prusa MK3S. This setup keeps the bed itself firmly in place within its frame, resulting in beautifully captured...

This is a Raspberry Camera Holder for Prusa I3 MK3S. It is fixed on the X axis. This is a remix of "Raspberry Camera Holder for Geeetech A10" (https://www.thingiverse.com/thing:3855161). Print Settings 1 x RaspberryCameroHolderArmPrimary :...

No support necessary The case for raspberry pi 4 B I used: https://www.thingiverse.com/thing:4111980 All parts listed below: 2x m3 screw 1x short m3 screw for PC AC cable with correctly angled end:...

Installing a cover plate on the exterior of my Anycubic i3 Mega 3D printer for the first time.

This is a custom-built Camera Holder for Prusa I3 MK3S. It's secured firmly in place along the X axis. This design is a modified version of "Raspberry Camera Holder for Geeetech A10" available on Thingiverse...

After numerous iterations and prototypes of other designs, I landed on this as my ultimate solution for mounting a Pi camera to the Pi Zero W situated inside my Prusa i3 MK3. I sought out a design that demanded no new mounting holes at all, and...

This is a minimalistic Raspberry Pi Case, designed to fit right behind the display of the Prusa Mini. It fits right on the aluminium extrusion and can be secured with a m3 screw and nut. (can be customised with the attached fusion file).<br>I aimed...

I designed a quick case to house a raspberry PI 4 on my prusa to minimize the extra wiring. Printing, the only parts that should need support are the hex bolt holes on the lid and the back of the cable arm. Required components 1x - 5v 3amp...

Raspberry Pi Enclosure with LM2596 Housing I've thoroughly dissected and enhanced a fantastic design, and I'm providing the STEP files to enable customization. ... Base Design Check out the original model here:...

Use supports, tall layer heights are fine.&nbsp;Get top case and more from: Marlo's

This is a simple print to hide/protect the Raspberry Pi Zero (or the Einsy Board if you have removed the RPi like I did).I copied the style from the original cover and printed it in black PLA on a textured sheet to make it blend in with the other...

Here is a custom box for the official Raspberry 7" Touch Screen designed specifically for the Hephestos Prusia i3 from Bq. I run Octoprint with Touch Ui and wanted to place the screen in a useful location. This case can be mounted directly to the...

I used the front bezel and screen retainer from Lewdfingers Raspberry Pi 7-Inch Touchscreen Enclosure I then designed all of the other parts to fit around it. I am using a Raspberry Pi 4 and wanted to add a fan since it's above the heated bed. I...

Set a user name and password.Boot up the Pi and SSH into it at xlcamera.local.Check Cameralibcamera-helloIncrease GPU memorysudo nano /boot/config.txtadd the following line:gpu_mem=256Get Packagessudo apt updatesudo apt install gitsudo apt-get...

Couldn't find a simple camera mount for the raspberry pi camera on the Prusa MK3, so I designed one myself. Inspired by the many mounts on the X-axis motor - what a fantastic idea! To attach to the X-axis motor, I used an M3x18 screw. I secured it...

Very adjustable camera holder for a Raspberry Pi Camera with adjustable focal length. The holder snaps onto the x-axis motor and sits rather tight. The ball joint allows for adjustment in various angles and was what I needed to make sure I could...

This design is for the Prusa Bear full upgrade and was created to match either the original Einsy Rambo case or one of the SKR cases I designed: v1.3 - https://www.thingiverse.com/thing:3929513 v1.4 - https://www.thingiverse.com/thing:4723441 This...

Pi Camera mount for the prusa xl, it is mounted to the left side of the CoreXY gentry.It will just pushed onto the frame without any bolds or screws. ...The camera case and base I used this model...

I've attached this thing to the right side of my Prusa i2 to hold my RaspberryPi with Octoprint installed. I mashed up the Rpi tray with some clamps I'm already using for my RAMPS board on the opposite side of the printer. I also added a bridge...