prusa i3 mods 3d models

Mounting the carriage at its highest point will optimize the z-axis build height. ...Currently, my setup reaches as high as 215mm, and further adjustments aren't strictly necessary.

Design inspiration, creative partner, and printer manufacturer: Ammo314, available at http://www.thingiverse.com/Ammo314. Designer credit goes to jacobian91 on thingiverse, located at http://www.thingiverse.com/jacobian91. This design is a remix of...

I adjust print settings to accommodate flexible filament requirements. Utilizing a compact section of 4mm outside diameter, 2mm inside diameter teflon tube serves as a precise guide hole. To achieve optimal results, you must lower printing speed by...

Remixed the Prusa i3 MK2 extruder mount for use in a Bowden setup, leveraging the publicly available Extruder Body file from Prusa to create this custom Bowden X Carriage Mount. ...The E3D Titan mount was used as inspiration and can be found at...

Remade the Prusa i3 MK2 Extruder Mount for use in a Bowden setup, leveraging the publicly available Extruder Body file from Prusa to create this Bowden X Carriage Mount. ...Utilized the E3D Titan mount, which can be found at...

Inspired by the Estamis LCD mod (https://www.thingiverse.com/thing:2764663), this remix utilizes the original power switch that comes with the MK3, maintaining the same size for the light switch (12.5 x 19mm). ...Additionally, I've removed the buzzer...

After upgrading my Prusa MK2.5 with the Bondtech Extruder and Bear Frame, I discovered it couldn't travel to the top of the Z Axis while housed within my Ikea Lack enclosure. Deciding to remove some material from the top of the enclosure using a...

Print Settings: Printer: Geeetech Prusa I3 A Pro Rafts: No rafts are used. Supports: Supports are not required. Resolution: The print resolution is set at 0.2mm. Infill: Infill density is set to 100%. ... Post-Printing: It's necessary to screw the...

Stay updated, as they are now fully modded and available for download here. Best of luck to all 3D printing enthusiasts out there. ... Material filament: PLA Layer height: 0.2 Shell thickness: 1.2 Fill density: 20% Print speed: 40 mm/s ...

This gathering contains an assortment of miscellaneous components that can prove valuable for customizing your Prusa i3 Mk2. ... Various items come with detailed descriptions and accompanying photographs, while others remain unexplained due to a lack of...

Standard Y-motor mount of Prusa i3 MK2 suffers from two problems: Only two screw points prevent NEMA17 damper installation; The mount is flimsy; after some days, the motor bends slightly and causes belt slippage over pulley borders (see photo). This...

I've revised the Prusa i3 mk3 print fan nozzle to fit the extra length of the E3D Volcano. Using it for about a week now, I'm pleased with its performance. I printed it from Colorfabb NGEN Orange filament which matches the Prusa orange perfectly at...

https://youtu.be/qhA5XOsIb3c Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No Resolution: .2 Infill: 20% Notes: Prints with out supports or raft, all standard settings. I designed the 3d part using the free 3d cad...

On some of my most intricate 3D print designs, I've discovered that the standard Prusa part cooling duct, which blows air solely from the front, is insufficient. Steep overhangs and fine details on the backside of the build plate seem to struggle as...

I have enough of false signals from my several Prusa mk3. Mk3s is better but still any 5 stars reliability. I designed this sensor with just one focus, reliability. It is not pretty, but it works without any false signal. Printing is easy, just...

This printer now utilizes a standard RepRapDiscount Smart Controller, upgraded with a high-precision potentiometer.

Modification of the Hephestos i3(http://reprap.org/wiki/Prusa_i3_Hephestos) Mount Fitted for Open Cable Chain (thing:611593) and Z Chain Redirected to Connect with P3 Steel Frame. I'm not completely satisfied with this setup, as z-axis height is...

I needed to transform my old Geetech Prusa i3 from direct drive to some sort of bowden drive. So I started from scratch designing one entirely. All the way from the z-axis motor and idler mounts to the upper z-axis brackets. ... This design was...

Update 18.09.19: My ability to support this mod has been severely limited due to no longer owning the Prusa printer. Update 15.05.19: You may need to raise the soft throttling limit to 70º on A+ if you observe throttling events. Other than that,...

As a result, the original PSU holder within the Prusa enclosure is no longer compatible with this new component. To resolve this issue, I have engineered a custom PSU holder that closely resembles its predecessor but features an added twist: a small...

To replace the spiral cable clamp with something else, I adapted this cable carrier chain: http://www.thingiverse.com/thing:611593 to make it fit on a 3D Phoenix. The right side is fixed on the extrusion motor, and the left side is fixed in the...

This is just the start...\r\n\r\nIt functions perfectly.\r\n\r\nGT2 28T Pulley x2\r\n\r\n852mm GT2 endless belt\r\n\r\nPrint 2 tops, 1 base \r\n\r\n605 bearings used for the idler base, secured with 3mm screws.\r\n\r\n604 bearings used for the belt...

I only grabbed a few basic lead screws and chose to rebuild the X Idler and X motor mount from scratch.

Purpose of this Mod is to utilize the E3D Volcano Hotend with the Original Prusa I3 MK2. This is a remix of the original Prusa I3 MK2 fan nozzle and extruder cover. The extruder body is a remix of Numbskulls and Steve-J's modified extruder body.

I have the Prusa i3 Mk3s with the MMU2S, but unfortunately, I've been unable to print anything reliably yet. The main issue seems to be the IR sensor, which has been problematic from the start. To troubleshoot this, I swapped out my stock extruder...

This is the mode that will enhance the stability/ strengthen the solidity of Prusa i3 printers, especially on axes Y and Z.\nHere is the explanatory video: https://youtu.be/xqdNIwB62JM\nPrint Settings\nPrinter:\n Prusa i3 Hephestos\n\n Rafts:\n...

I have the Prusa i3 Mk3s with the MMU2S. I have not been able to reliably print anything yet without issues. I've narrowed it down to what I consider to be, by far, the largest issue. The IR sensor. I swapped my stock extruder with the Bear extruder....

This is an updated version of the Prusa i3 Mk3r fan holder, redesigned to hold the blower at a 45-degree angle. ...I've repositioned the arm further to one side, creating space for a Moons motor attachment on the extruder and accommodating motor wiring...

This is a remix of the work done by P4ckit, https://www.thingiverse.com/thing:2833311 After the new update for fan orientation from Prusa, my camera kept getting hit. I remixed this to make it easier to install a new one at a measured distance and...

......It has turned out to be surprisingly practical. Print instructionsThis is a remix of the original z-axis file provided by PRUSA but I don't know where the original files are held on this site, if at all. Print in PETG at .2 layer height, grid infill.