prusa i3 mk3s octoprint profile 3d models

Although Prusa's supportive documentation assures me these temperatures are normal, out of caution and anticipating future prints with ABS in an enclosure, I decided to create a small fan bracket to clip directly onto the Extruder motor. Cold air is...

Orient Flat side down, no supports needed.I know it fits on the MK3S+ but I'm unfamiliar with what other printers came with so if you have another and verify, please leave a comment so others know!I look forward to hearing any feedback, tips,...

Unfortunately, my USB cables stuck down a little too far and got blocked by the main wire loom coming out of the i3's main board. My solution was to create a simple stick with some holes in it that would lift the case high enough so I no longer had...

Also, you'll need 2x M3 hex nuts to insert into the clamp nuts, and M3x20 bolts (I used leftovers from my Prusa build). Washers underneath the bolts are recommended, to distribute the pressure better to the printed material. ...If you use a thicker...

Although the kind Prusa support team assured me that these temperatures were within acceptable limits, I still had my doubts, especially considering my future plans for printing ABS in an enclosure setup. To err on the side of caution, I decided to...

This is a simple Allen Key Holder designed to be mounted on top of your Prusa Printer, keeping them readily available at all times. Four versions are available, each catering to different needs. For a snug fit, choose the version with the Hex-Mount,...

The rest of the parts remain the same as the original thing, but I have also added an amended Einsy door with a notch taken out of it for the light power cable (where the kabelkanal meets the top of the Einsy enclosure), and created some clips to...

This is just a simple Allen Key Holder that you can mount on the top of your Prusa Printer to have them ready at all times. There are four Versions available. One for a tighter Fit of the Hex-Mount and one for a loose one. I recommend the Tight one...

This is just a simple Allen Key Holder that you can mount on the top of your Prusa Printer to have them ready at all times. There are four Versions available. One for a tighter Fit of the Hex-Mount and one for a loose one. I recommend the Tight one...

I'm using a combination of the original Prusa parts and a new part to optimize my printer for large area prints. I've found that sometimes warping occurs when printing with ABS, so I've made some changes to prevent air from blowing onto the print bed...

This enclosure design is inspired by the Prusa Ikea Lack enclosure. I designed this enclosure because I wanted to have a higher enclosure to mould spool holders inside the enclosure, and I didn't want to remove the PSU, but still wanted it outside...

This is partly a remix of the original Prusa parts, and a new part. Since I occasionally had warping with large area prints, I optimized the printer so that the air did not blow onto the print bed through the hotend. Since I am operating the printer...

This is partly a remix of the original Prusa parts, and a new part. Since I occasionally had warping with large area prints, I optimized the printer so that the air did not blow onto the print bed through the hotend. Since I am operating the printer...

For easier loading of filament, I remixed the Bondtech Prusa i3 MK2.5S / MK3S / MK3S+ extruder sensor cover to add a tapered tube for the filament loading hole.Print with PETG as oriented - no supports.Bondtech github part link ( Sensor Cover...

[Japanese] PRUSA i3 MK2.5S/MK3S/MK3S+のホットエンドに挿入するPTFEチューブは両端を60度のベベルカットにしなくてはいけません。純正品を購入したりセンタードリル等を使って加工することが推奨されていますが、もっと手軽に製作できるように一般的なアートナイフ（OLFA 10B/10BS）を使ってカットと両端のトリムを行えるジグを作成しました。 MK3S+用（42.3mm） または...

Simple combi tool (spacer holder and wrench) for quicker and easier application of the “Nylock Mod” on a Prusa I3 MK3S/MK3S+. One end of the tool can be used as a wrench to turn the nylock nuts. The other end contains an 6mm socket where you can...

I wanted something easier to get on and off if I had to.That's when I came across FLink's light frame project (https://www.prusaprinters.org/prints/37475-led-frame-mk3s) which I considered to be slightly overkill for my needs but I liked his mounting...

Many of the guides I tried did not fit well on the frame, so I designed this one from several other designs. ...It is easily attached to the frame, but it is firmly attached!

This is for: MK3/MK3S/MK3S+ and Pi4 Yet another remix of the 4” HyperPixel cover for the Prusa MK3S+ for the Pi4 to be used with Octoprint and Octodash. ... Complete details and build instructions are here:...

This is a remix of the amazing raspberry pi case created by hofftari, specifically designed for mounting on the Prusa i3 printer. I wanted to give my case an extra touch of personality, so I chose to use a design that highlights the Octopi/Octoprint...

I made a camera stand, that attached to the bed of my Prusa i3 printer, so I could get time-lapse video of my prints. I used octoprint and a raspberry pi 3. Below there is a link for the camera. I also used short m4 screw threads and pushed them into...

... Print Settings: Printer: Prusa i3 MK2 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 100% Notes: Try to print the parts as shown in the Slic3r screenshot above. ... Print List: 1x Custom Bot Case 1x Top Case 2x Holder Arms

Relocated fan for better hot end access. Need to remove fan housing nubs. Fit up required. Glue will keep fan in place. ... Allen key handles https://www.thingiverse.com/thing:980720 pinda relocation: ...

<p>This is a multi size nozzle holder. I had purchased a pack on amazon and could not find a holder that held my range of size. I made one plain and one labeled for the mk3. ...Currently printing in .4mm nozzle but the size text might be a little...

0.20 mm layer height0.4 mm nozzleMounting steps are the same as here: https://www.thingiverse.com/thing:4223581 - using the lock is optional.

English: Reverse bowden system consisting of: - Extruder cover with M5 thread - Z axis cover (left/right) with holder for an IQS-MSV 4mm connector I use an PTFE-Tube with 4mm diameter and 1m length, IQS-MSV fitting...

I've been plagued by spools wobbling loose from my spool holder due to the limited width of the spool. To prevent this issue, I took matters into my own hands and designed custom spool holders with enlarged parts. ...These new holders feature 5mm, 10mm,...

Nice filament guide with quick clip function on the printer frame. Because of the design, there is no risk of the extruder colliding against it during high Z travel. In addition to the small opening, which also allows a side filament insertion...

<p>Nice filament guide with quick clip function on the printer frame. Because of the design, there is no risk of the extruder colliding against it during high Z travel.</p><p>In addition to the small opening, which also allows a side filament...

Hello, Here is a diffuser design with eight symmetrically arranged openings facing hot end, for balanced cooling.