prusa i3 mk2 3d printer

This is a 3D-Printable [OpenSCAD](https://openscad.org/) model of a front fan mount for an HP Z4 G4 workstation. This is in no way endorsed by HP. Also, the author is not responsible for any damage resulting from its use. ## Model and Parts ...

There is a bit of tolerance built into this to make it a tight fit with respect to the slight shrinkage that happens in 3D printing. Be prepared to use clamps to squeeze the nut into place. Mine was able to just push in with my thumb. - qty. 2 of...

based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 All of which is very much derived from the excellent design here:...

Here are the parts (top down): Antenna Head Visor Eyes (2) Teeth Body, upper Body, lower Door Arm segment, shoulder (2) Arm segment, short (10)* Hand (2) Leg segment, hip (2) Leg segment, short (8)* Leg segment, ankle (2) Foot (2) Stand Also...

If you have any questions about the print, please feel free to reach out.If you enjoyed this print, or would like to help spawn future 3d prints, there are multiple ways to support me. You can donate, through Patreon or Paypal, and you can also...

Description: A set of 3d printable parts to compactly combine two LRS-350 PSUs into a compact unit with optional voltage and current displays. I put this device together so i could consolidate the 10+ individual power bricks for each compute node in...

... the Fine tuning adapter / rod holder. NOTE: Some more of my other designs: https://www.thingiverse.com/leadingedge/designs Best All-round 3D Printable Knife and scissors sharpener with lots of attachments: https://www.thingiverse.com/thing:4135236

3D print What you'll need You need to print the stand and the cover once. Plus, you need one brass inlet (4mm outer diameter, 3mm inner) and a M3 screw. You just use some soldering iron, to melt it into place. NOTE: You could also modify the attached...

(be careful and slow with this as you do not want to melt the plastic)Possible improvements to the model for advanced 3d modellers:A better guidance for led strips so you can make it perfectly even across the sides and perhaps also the edges.The...

If there are any errors or you have requests for special changes to design, please let me know in the comments. All pieces are support free!Let's start with the list of parts you will need to complete the project:3D printed parts (See...

Filament seen here is marble PLA. Required Parts/Tools for Assembly:3D Printed Parts2x - Wheel2x - Leg6x - Pot1x - Axle2x - Axle Cap3x - SpacerTools (All Optional)HammerSuper Glue Assembly Instructions:All of the parts that need to be...

There are several 3d printed threaded parts. The internal threads should be cleaned out with a 6mm X 1mm tap. If you don't have a tap you may be able to use a 6mm bolt with a groove dremeled into it. I haven't had to use a die to clean up the...

This steering wheel is a remix from this https://www.thingiverse.com/thing:4058270I designed almost every parts in Fusion 360, the only files used from the parent are the handles.The plate can be 3D printed but on my design it was a carbon plate, i...

This way you won't need to 3d print the spacer and buy those PGN bearings separately to fit their truck and wont need to print the bearing adapter. The bearings I bought didn’t fit the Aliex rims (was a little loose) so I printed the adapter. The...

Join our Tribe or Patreon to receive amazing 3D printable miniatures sets each month for a very special price! Save big on the complete Noble Alfar bundle, which also contains pre-supported files for each STL. Please check the images to see what it...

Most things shouldn't need supports except for the bottom-wall-mount.stl and bracket-top.stl.Non-3D printed components I used:A lot of M3 hex socket screws and nuts of varying lengths (6,8,12,16,20mm). The nuts should be hex, not square</li><li>5...

Design is done by 3D-modeling using CAD Pro Engineer, prototype engines by using Lost Wax moulding and / or Rapid Prototyping , test runs and mass production in our facilities. 3W – History 1985 Introduction of the first 2-stroke gasoline...

DBA 3D Gloop! makes no representations on behalf of Valve Corporation or any of its subsidiaries. The content published herein are presumed adaptations of the original copyright holder and are provided to the public under Section 107 of the Copyright...

I am using all 2040 V-Slot for this build, 4 - 2040x250mm lengths for the base parts connected with 3D printed brackets. You could also use standard corner, inside Hidden Corner brackets or L brackets. The Carriage X axis is 2040x500mm and carriage...

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. ...Scan the World is...

In this case my 3D-printed adapter is a simple 65 mm tube of suitable outer diameter. Other LED flashlights have a contact spring at the positive terminal (usually located towards the LED) or even at both ends (LED side and end cap side). In this...

Join our Tribe or Patreon to receive amazing 3D printable miniatures set each month for a very special price!  Save big on the complete Bronzeclad Greatgoblins bundle, which also contains pre-supported files for each STL. Please check the images to...

  A bit of extra info: Customizer is based on OpenSCAD, a program that can generate 3D models out of a set of instructions. A customizer file is just a .scad file with specific formatting. You can use any version of OpenSCAD to load and edit a...

Send me a message if you have a particular chess set design that you would like to see as a 3D model. I am always open to new ideas. Although I have steered clear of the Staunton design, I am considering adding the more popular formats, like the 1959...

The frame is entirely 3D-printed, but some components need to be purchased separately (more details below).Recommended componentsMotors2306 minimum for this build, I would recommend even something larger like 2508My build had 2206 motors, which felt...

If you use the F3D files, go easy on me as I've only been using Fusion 360 for a month and its the first time I've ever been exposed to 3D modelling. I'm sure there are faster, more efficient, and proper way of doing things as oppose to the way that...

Here is a link explaining it Print instructionsThe parts: Base: I printed mine with 0.2mm layers. Should have enough perimeters to make the side chamber walls solid. Should be printed in a very dark color, unless you want light too bleed trough the...

PLA has an inherent shrinkage factor, and that varies depending the type of PLA you use and all the other many things that go into 3D printing. You may need to adjust your slicer to (every so slightly) enlarge or shrink the part. Z-axis dimensions...

The project is fully 3d printed, with an 8 LED neopixel ring, an Arduino Uno, A piezo buzzer, an infrared receiver (+ remote), a push switch, and wire. (Including all the tools necessary to use these). And optionally, a 1000μf capacitor and a 400...

Make your own custom chips.Accessories&nbsp;DescriptionImageFCS Label Mounting SolutionUse this to label what filament is stored in your dry box, Ikea samla or where ever else you want to label filament.FCS Label StandUse this to see what material...