prusa extruder blob 3d models

You'll need two of this one item to get started, making it compatible with my own direct drive extruder, the Airtripper BSP v3, modified for flexible filament, Geared Extruder by terenceang, as well as others that share a similar design.

... scratching your extruder cables. ...After months of use, you may notice that your extruder cables show signs of wear. ...The nylon guide can become dislodged, causing the cables to take on an incorrect angle, which can lead to premature fatigue.

I was looking for a smaller type of extruder indicator, did not find one small enough for my needs, so made this one. ...This will fit within the dimensions of the extruder motor backside and is intended for use with a 7x3 mm magnet glued in place.

... that match the M3 screws commonly used in 3D printing applications. UPDATE: This design has been successfully tested with M3 screws and can be used for attaching fans to various 3D printers, including the Prusa i3. ... Prusai3extruderfanmount2.stl

A very simple Extruder pointer for the Pusa mk3/s. I use it with three 8x2mm disk magnets. ...And I uploaded three different hole sizes so depending on your printer you can achieve a good press fit.

Bondtech bmg extruder design is a game-changer, delivering tremendous torque and performance. If you think it needs some adjustments, just let me know and I'll be happy to try and fine-tune the design for you. To get the most out of this extruder,...

A remix of pilniczek's excellent dust filter, adapted for the MK3S+ Prusa part print settings recommended:.20 layer height20% infill

I'm making some minor adjustments to my trusty Prusa Mendel printer. ...It's a variation on the Nema motor bracket, which can be found at thingiverse.com under #1318849.

Thingiverse is a slow ride. ...I'm ditching it for good, headed to https://www.prusaprinters.org/prints/26389-corona-printhead-for-prusa-mk3s-and-possibly-other. ...You'll find all the .stl files and more on prusaprinters.

The extruder carrier began as a standalone unit featuring built-in bearing holders, but another holder was found, which proved more suitable (thanks to toolson). The new design can be used to swap jobs between an MK8 and Bowden setups. Toolson's base...

There is a newer version of this using the Prusa 'Dyson' technique at: https://www.thingiverse.com/thing:3357264 This thing replaces the stock E3Dv6 hotend on a stock Prusa MK3 with Slice Engineering’s Mosquito hotend, utilizing existing mounts and...

... This has now been corrected with new extruder cover and extruder body parts. Update (29/11/18): The x carriage file was slightly edited in the cable guide area behind the hotend fan to ensure that all geometry was touching the first layer.

6/22/14 An E3D V6 version has been made and all parts are the same except for the Extruder Mount and Mount Lock. X-Carriage nut traps redesigned for more strength. 6/23/14 All parts out of work in progress and tested. If you make this please...

This will help when printing PLA in particular to avoid heat creep issues.The part is printed in PETG without any supports, with the faceplate of the extruder down on the print bed. The holes are compatible with the existing Noctua 40x10mm fan, and...

All parts are compatible with this kit -> http://www.ebay.com/itm/Greg-Wade-Reloaded-Extruder-3D-Printer-Screws-Bearings-Springs-Hobbed-Bolts-/161674059456. ... Print Settings: Printer Brand: RepRap Printer: MendelMax 1.5 Rafts: No Supports: No...

Update (5/11/18): An issue was found with the extruder cover and extruder body parts where they overlap in the design and are therefore unable to be assembled. This has now been corrected with new extruder cover and extruder body parts. Update...

Modified Remix to Clear Prusa MK3S Hotend Fan Clearance To allow for smooth printing on the Prusa MK3S, a slight modification has been made to the hotend fan clearance. This adjustment is crucial for optimal performance. *Important Note*: The...

... ... The working Bondtech add-on for the MK3 Bondtech extruder has been modified to accept an M10 style pneumatic coupling for a reverse Bowden setup. ... Print the cover at 0.15mm layer height to get better definition on the threads for the coupling.

Bondtech bmg extruder design. Works great, lots of torque. If you think it need some tweeks, just let me know, and I will try to design it ;) You need to set your E-steps to 830! ... To set E-steps: M92 E830 (Set Axis Steps-per-unit) M500 (Store...

... breaking down. ...Tightening the installation process can be somewhat challenging. To overcome this hurdle, it's necessary to disconnect the extruder cable, allowing it to slide over the motor with ease. ...Perhaps I'll revisit the design altogether.

The fully tested Bondtech add-on for the MK3 Bondtech extruder has been engineered to accommodate an M10 style pneumatic connector for a reversed Bowden configuration. ... Print the casing at 0.15mm layer height to achieve superior definition on the...

The attachment mechanism utilizes six pairs of 6x2 millimeter circular magnets that securely fasten the body to the extruder. This design ensures a robust and reliable connection, guaranteeing optimal performance during operation. ...The magnetic...

... much better now. It has greatly improved the filament feed. Print Settings Printer Brand: RepRap Printer: Prusa I3 steel Resolution: 0.2 Infill: 100 Notes: The more support, the merrier. ...Post-Printing A little bit of fine-tuning may be required.

I secured the Prusa i3 Aluminum frame onto its mount by attaching it to the rear side of the Z rod assembly with locknuts and longer screws. To complement this setup, I strongly recommend employing a spool holder designed like this one:...

... with tie-wraps, then attached it to the plate. Next, I fastened the plate to the X-belt clamps using possibly longer bolts for a snug fit. Finally, I wired the fan to my electronics and printed with active extruder cooling for enhanced performance.

Pull the extruder tab with one hand, insert this tool as shown in the picture and release. Now you are free to remove or insert a filament. Remove the tool before printing. The default thickness of the tool is 5mm. If you want to tweak any of the...

Pull the extruder tab with one hand, slide in the tool as demonstrated and release your grip. Now you have the flexibility to replace or add new filament effortlessly. Make sure to remove the tool before printing takes place. The default size of this...

The key difference here lies in the fact that the filament path is situated as close to the hobbed gear as possible, minimizing the amount of bending required from the filament.\nThe extruder achieves positive grip through a spring tensioner located...

Hey guys, Here's a different Visualizer for the original Prusa. Be sure to set "Allow Single Wall Extrusion" under "Advanced" in S3D (check out the picture). You'll need an 8x3 magnet, which simply plugs into the back and doesn't require any glue or...

In our version 4.2, we've made some improvements and fixes, including required parts such as: - 7x m3 x 16mm - 2x m3 x 22mm (or more) - 3x m3 x 10mm (for motors) - 14x m3 nuts - 2x m3 washers - 1x spring - 1x m3 bolt, length ~40mm (depending on...