prusa enclosure v2 3d models

This is a remix of a TinkerCad design created by user rayshobbyshop. It is an enclosure for board version 1.4 of the garage door controller from opengarage.io. ...Other controller versions may also fit, but YMMV. Features... Designed to fit the...

Hi, An enclosure for the Nano VNA V2. With a holder for the open, short, load and barrel connector. under a lid. The stylus has it's own place too. It can be used to take out the SMA connectors.</p> <p>If you have some transparent filament left you...

This is a full enclosure for the SeeMeCNC Rostock Max V2. It has double doors on all three sides that swing open fully, allowing easy access to the build area. I designed this enclosure to create a heated chamber and capture noxious fumes from ABS...

Creating the [Prusa Lack enclosure](https://www.thingiverse.com/thing:2864118) I ran into various issues. One of them is that I could not find 3mm thick plexiglass. Was hoping that the fitting would still be snug enough to hold the plexi. To...

Creating the Prusa Lack enclosure (https://www.thingiverse.com/thing:2864118) I ran into various issues. One of them is that I could not find 3mm thick plexiglass. Was hoping that the fitting would still be snug enough to hold the plexi. To solve...

Needed a way to hold two USB extension cables…One is from the printer's memory stick slot, the other is from the computer.I don't like plugging the USB stick in and out of the printer directly (so as not to wear out the port) it's much cheaper to...

I wanted a very compact and simple webcam mount for my Logitech C920 with a standard ¼ inch thread to attach to one corner of the Original Prusa Enclosure.On one side, it has a 2.8mm hole to attach with an M3x8 screw (use one of the spares that come...

 Enough enclosure height to put the filament on the printer inside the enclosure.Slide-in front doors. If you print PLA or PETG in a warm season, you can slide in the front doors to the side.LED lights; the switch is on the front panel.  Prusa PSU...

Hi all, I decided to built the Lack Enclosure for the PRUSA MK3S+ described by: https://www.thingiverse.com/thing:2864118, https://blog.prusaprinters.org/cheap-simple-3d-printer-enclosure_7785/ In general they did some good work, however in my...

You can try this 1meter cable:https://www.amazon.com/uxcell-Ribbon-Connector-2-54mm-Length/dp/B07S1W1KW3&nbsp;19mm X 24mm grommet to run cables back into the case.The switch extension :...

Top supports for an enclosure i am creating for the 3d Printer

mount for prpus enclosure. ...I edited bottom corners and i add 100mm for oiginal corners.

... control board. Can be printed without supports in proper orientation. Magnet slots included if enclosure uses non-rigid enclosure plastic/fabric and want to make a ring to “clamp” enclosure surround. ...Vents work for a 24" side to side enclosure.

Credits to cisardom for thing https://www.thingiverse.com/thing:2864118 and Mikolas Zuza for the guide https://blog.prusaprinters.org/cheap-simple-3d-printer-enclosure/ I was a bit unhappy with the final build because cutting the plexi to 440 x 440mm...

Assemble a MintyBoost without their battery holder from Adafruit, insert into one enclosure half, place battery clips around bosses, solder positive and negative leads, and add a jumper wire. ...Attach the cover to the other half, ensuring a snug fit,...

a 15mm spacer to add space on the ikea lack printer enclosure leg ends. ...helpful if you bought the wrong size acrylic or need to add height to the enclosure.

In an effort to make the Prusa Enclosure less deep I mounted the PSU to the side instead of the back.If you want to do this I feel obliged to say that, minor as it may be, this causes irreversable damage. Namely a hoop for a tie wrap on the metal...

Official Confidential Files for Advanced Tachyon Warhead System V2.0 Engineered for High-Resolution Laser Sintering Printing, yet capable of precise output on Fused Deposition Modeling printers with adjusted parameters and precision settings.

I loved the original heatbed cover and wanted to stick with it after the replacement. I had to use the enclosure after installing the original heatbed cable cover, therefore I designed a flanged cable cover to be mounted on a cutout in the acrylic...

I designed this because I needed a very small enclosure for a feather MCU. It accommodates a small 150 mAh LiPo battery and a power switch. It also has an opening to plug the micro USB connector. The top and bottom stay tightly together via pressure....

Enclosure for a LM2596 Buck converter with an potentiometerThere is a lid with text, and with no text.---------------------------------------------------My settings:PETGLayer height: 0.2Perimeters: 3Infill: 15%No supports

Removed all stabilization material visible in the cut window, but leave the floor unharmed. Remove the most top table from your printer enclosure tower and place the cut table directly on the other table. Put a 40x40 cm concrete platter inside the...

To see how this looks on your printer, check out these videos: https://www.instagram.com/p/B2VuI-Bjjf9/?utm_source=ig_web_button_share_sheet https://www.instagram.com/p/B2Zv7HuHQco/?utm_source=ig_web_button_share_sheet I wanted to build lightbar...

Control airflow within the enclosure to ensure optimal performance. ...Include the following hardware: Six (6) M3 screws Six (6) M4 screws Six (6) M4 nuts

This printer enclosure is fabricated using Solidworks software. ...It's produced by printing with Colorfabb nGen material, featuring a 0.3 millimeter layer height and three parameters.

This tool holder will be mounted onto the MK4 enclosure to hold a snip, brush, scraper and small parts within a basket.

A stronger enclosure latch. This version of the latch uses stronger 6mm x 6mm magnets that don't need to be glued in place and can be removed if necessary. ... Remix of https://www.printables.com/model/85891-magnetic-latch Bill of Materials 6x 6mm...

A stronger enclosure latch. ...&nbsp;This version of the latch uses stronger 6mm x 6mm magnets that don't need to be glued in place and can be removed if necessary.</p><p><strong>Bill of Materials</strong><br>6x 6mm x 6mm round magnets<br>6x M4 16mm...

It features partial parametrization, allowing you to adjust specific parameters in the code for an enclosure tailored to your inner volume, hole placements, and material thickness. The script generates DXF files suitable for laser cutting. Future...

In our second Filastruder enclosure design, we incorporated a spine for increased rigidity and support during extrusion without a side panel. Follow the upgrade instructions to add this feature to your Filastruder kit. You'll need 1/4 plywood for...