prusa enclosure lack 3d models

Credits to cisardom for thing https://www.thingiverse.com/thing:2864118 and Mikolas Zuza for the guide https://blog.prusaprinters.org/cheap-simple-3d-printer-enclosure/ I was a bit unhappy with the final build because cutting the plexi to 440 x 440mm...

I wanted to elevate my MMU2 onto my lack enclosure's top, so I could work on it without needing to access the enclosure or alter its height. The mount screws directly into the lack table's top using drywall screws. The frame mounts remain intact on...

built a lack enclosure for my printer and the PSU cords were too short, needed to run them through the bottom of the table. ...Used a 25mm hole drill in the table and then put this in, was able to run both PSU cords through it and attach to the board...

Removed all stabilization material visible in the cut window, but leave the floor unharmed. Remove the most top table from your printer enclosure tower and place the cut table directly on the other table. Put a 40x40 cm concrete platter inside the...

My i3 MK3 printer basically consist of three stacked Lack Tables ( see link ), where the upper is the modified enclosure and does reside on wheels. ...In order to be able to pull and push it around, I needed handles. I found bwolfey's handle ( see remix...

Stacking Lack Tables to build a enclosure is a brilliant idea. But I didn't feal much confident in the vibrations the printer send into that structure. So I designed these 2 connetion elements to fix one Table to the next one. I stacked 3 tables...

I modified the magnetic handles and base for Dominik Císař's Prusa enclosure (https://www.thingiverse.com/thing:2864118) as well as JesusFreke's redesigned handles (https://www.thingiverse.com/thing:2922505). I discovered that using 1/2" x 1/16"...

Remove the most top table from your printer enclosure tower and place the cut table directly on the other table. Put a 40x40 cm concrete platter inside the cut window. Do not try to do it the other way around, lifting the cut plate with the...

Creates storage for 3D printer and supplies ###Benefits of this enclosure: 1. Well-lit buildplate via internal lighting 2. Fire protection via hard-wired smoke detector 3. Knowledge of internal temperature and humidity via sensor output to control...

You can now mix and match the large and small pieces as needed, depending on your clearance between the top of the printer frame and your enclosure ceiling. The mini version includes two different sized nuts, a 12mm nut and a 14mm nut. I designed...

I built a custom enclosure for my printer that allowed me to neatly route the PSU cables underneath the table. The PSU cords were too short, so I had to drill a 25mm hole in the table's bottom to run them through. ...I then placed the cable management...

Original door handles can break their front lip while inserting the plexiglass, so I made this strenghtened remix. There is also a remix for 5 mm x 2 mm round neodymium magnets. Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports:...

This design adds support to the underside of a standard 'Prusa enclosure size' lack tabletop, allowing for removal of the top where the printer sits and replacement with a concrete paver stone. This setup offers maximum head space while reducing...

Two signs "Original Prusa MK3S" and "Original Prusa Mini", intended to be mounted on a LACK enclosure, or any other enclosure, or wherever you like. v1.1 1/1/2021: Increased height of lettering. Disclaimer: I have no relationship with Prusa, this...

a 15mm spacer to add space on the ikea lack printer enclosure leg ends. ...helpful if you bought the wrong size acrylic or need to add height to the enclosure.

This is a project based on the Ikea LACK as a starting point. I designed some components, modified others, and the end result is straightforward to both print and assemble. ... Things to purchase: 50 cm x 50 cm Polystyrene panels (I used 2.6mm...

LCD Enclosure (Wide Version) for Prusa MK3 Lack Enclosure, this is the wide version, Short version here, https://www.thingiverse.com/thing:3432396 W~5.259" D~3.734" H~1.759" Mounts to ceiling of Lack Enclosure Rear Lid, No supports, edges of clips...

<p>This spoolholder fits most common 1 kg spools. ...It is supposed to be glued on top of the Prusa Lack enclosure.

Prusa owners can easily and quickly swap out spools with a custom-built spool holder designed specifically for their Ikea Lack Enclosures. ...This innovative holder allows users to load new filament directly onto its surface, streamlining the printing...

I designed an exhaust fan system for the Prusa Lack Enclosure v2. This allows for printing PLA with the enclosure doors closed. I saw a noticeable improvement of 5-6C decrease in chamber temps, which allows me to print PLA without heat creep. ... ...

Mount any 'ball and socket fixture' camera (https://www.thingiverse.com/thing:4647833) or accessory inside your Prusa MMU2s Lack Enclosure. Simply insert between the screws and existing enclosure supports. ... Also included is a version for a...

Conveniently attached to the side of my trusty Prusa i3 Lack Table Enclosure, this setup is perfect for effortless data transfer and storage management. ... EQUIPMENT: Two #10 x 3/4" screws are precisely fitted to secure the enclosure with seamless...

Customized Lack Enclosure for Prusa i3 MK2.5 mounts all electronics outside of enclosure. Using Thingiverse's 3160443, I'm attaching the MMU2 to the top of the Customized Lack Enclosure. Thingiverse's 3157502 is used for spool holders. Omitting...

Remix of the original Prusa Cable Holder/Bushing that allows you to pass 2 USB cables, 2 Wyze Cam's flat cables, and a power cord through.Additional Related Models:Mirrored Back Leg for Prusa Lack EnclosureThis model replaces the bottom back left...

I decided to modify my Prusa Lack table enclosure setup by adding a third Lack table, but it ended up being too tall for me, so I cut about 5 inches off each leg. Now, four copies of this design attach to the corners and middle table of the top...

Mount your LCD screen securely outside your Lack table enclosure using two M6 wood screws. The LCD bracket design by Prusa serves as a foundation, requiring only a swap of the two brackets for compatibility with the main part of the 3D-printed LCD...

... ...Designed to securely fasten onto the Prusa Lack enclosure's top surface, this practical solution is ideal for everyday use. ...Printed at a precision of 0.35 millimeters per layer, its robust structure ensures seamless functionality and durability.

I redesigned the Prusa Enclosure PSU Holder after cutting Ikea Lack legs too short on accident. ...The modifications trim down the PSU Holder by relocating the screw hole to its side and freeing up some space for wire clearance between the PSU and the...

A tool holder for all the bits and pieces I was keeping in the one of the boxes that came with my Prusa i3 Mk 3. ...It mounts to the side of a lack enclosure. ...The screw holes are designed for #6 flat head countersunk wood screws.

this is a remix of GOATDIY for the LACK enclosure gap fillers. https://www.prusaprinters.org/prints/17934-prusa-lack-enclosure-gap-fillers Great design and much better looking for the IKEA enclosure. However it seems there is a problem on the...