proton pack build 3d models

 Ghostbusters Afterlife introduced a key new part to the Proton Pack, the POWER SWITCH! This model is non-functional, but was unreachable by a 'Buster anyway! It goes on the underside of the Ion Arm assembly, as seen in this reference...

This is slip on replacement booster tube for the Spirit Halloween proton pack. I designed it in Tinkercad. It will require a small amount of filler and sanding, then can be painted and super-glued in place. I printed it on my Ender 3 V1 using one of...

This was made using in film reference, notes from crew, as well as detailed photos of the SDCC proton pack and the Olympia pack. Scaled from references based off of known objects on the pack taking into account perspective distortion and other...

Here is the Frozen Empire Power Cell door replacement for the Haslab proton Pack. I have gotten two prints that fit perfectly so far. I recommend resin printing for the sake of dimensional Accuracy. You will need to reuse the internal components from...

This file serves as a template for replacing or upgrading the Booster tube within the Spirit Halloween Ghostbusters Proton Pack. Although I haven't printed or utilized the complete replacement tube, it should fit properly. If I were to create another...

This is the first pass at a shoulder mounted trigger box for venting both your Proton Pack, and a Ghost Trap if it's connected to the pack in some way (for me, most likely on the PowerCell like the RGB cartoon). The intention is to have two toggle...

========================================================== The other ear tabs are for replacing the bumper completely *THEY ARE CURRENTLY ONLY TESTED ON Q-PACK MK3 AND 3.1 BUMPERS* These ears are designed to slide into the current slots that are on...

I used film references, notes from the crew and detailed photos of the SDCC proton pack and Olympia pack to create this model. The design is scaled from known objects on the pack, taking into account perspective distortion and other factors. I...

Drop in replacement for the Haslabs Proton pack bumper foot with the relief in the bottom to pull it in and get rid of that weird gap. I included a spacer so you don't break your pack, beware, it will probably pop into place when you get it seated...

A Gun Hook sized for the Spirit Halloween Proton Pack Neutrino Wand resized from Notsabbat's Trigger tip for 7/8" diameter Nutrino/Nutrona wand design. The base white tube on the spirit back is 5/8 OD, this gun hook is scaled for that size and...

This was created using film reference, notes from the crew, as well as detailed photos of the SDCC proton pack and the Olympia pack. Scaled from references based off known objects on the pack taking into account perspective distortion, viewing angle,...

Here are the models I used to upgrade my Spirit Halloween Ghostbusters Proton Pack. The upgrades include an Arduino with some neopixels for always-on powercell and cyclotron animations. I resized and updated DancinFools V Hook to work on the spirit...

This was made using in film reference, notes from crew, as well as detailed photos of the SDCC proton pack and the Olympia pack. Scaled from references based off of known objects on the pack taking into account perspective distortion, viewing angle,...

... ...The Dale PH-25 Resistor on the Ion Arm. Print it up, no supports needed and slip it right over the top of the existing nub on the pack. Totally transforms it to give it a much more realistic look. ... Lemme know what you think in the comments!

... a block on the side where the tubes should fit into. So I purchased a blue tube from GBFANS.com and cut two equal lengths, painted one red and designed and printed this modification to the pack. ... Lemme know what you think in the comments below!

Build a print with a base featuring a hole, directly onto the build plate, and utilize support for the hook as well. ...This miniature design necessitates an enlarged scale of 10 times its original size, thus requiring adjusted printing specifications...

Here are the changes I made: Wand hook: https://www.thingiverse.com/thing:2972587 LED holders for the wand: https://www.thingiverse.com/thing:2982288 Neopixel change to the bargraph: https://www.thingiverse.com/thing:2976341 Neopixel used for...

I noticed the red tubing on the bottom of the pack was too small, and the blue tube was nowhere to be found. The piece holding onto the red tube has two screws that allow you to easily remove half of it. I created a new part that screws into its...

... Wand. It will require removing to stock loom on the pack and replacing it. Replace with 3/4" Non Split Loom. (Split Loom will most likely work too) Feel free to ask any questions. ...I'll try to do a more detailed write up at a later date.

Wanted something to fix that terrible molded-in crank knob on the Spirit pack, so I came up with this cover that slips right over the top of the existing knob to give it a more complete look. Depending on your printer, supports may need to be used...

The original was a little too wide for my pack, and it didn't fit the Dayton Audio 2.5" speaker. This one fits great for me, but you still need to trim the speaker hold down as Beezlebot specified. ...It would a cool modification to have it fit the...

... The conversion process, fixing issues, and scaling require significant effort. As an update, I've added a military knob, though it may not be as detailed as desired. Nonetheless, please find it below. I hope these models aid your builds. ...Enjoy!

... it's a lot of work. EDIT: I've just added the military knob too. It's not as detailed as I'd like, so I don't know if it will work for you all. But here it is anyway. So, I hope this helps some of you with your builds. Enjoy. ... Category: Props

Please note: The lenses DO NOT line up with the stock holes on your pack. You will need to drill holes into the original cyclotron that line up with these holes. Dimensions were not referenced for the lenses. They were literally pulled out of my...

Thanks to mr_kiou, I was able to slice and dice this crank knob an build a kit to allow for a spinning crank knob. This prints in 3 parts: handle, body, and cap. This print is intended for resin printers. I dont think FDM has the tolerance for this...

I've taken the original remix, corrected the sizing issue that arose when someone else remixed it, and bumped up the size by a full 5%. I'm eager to see how it turns out - please share a pic if you create something with this revised remix. If you...

The original design was revamped to serve as a versatile light switch plate.

This is just the smaller slot since there are more of them. ...I recommend printing at 101% as 100% is a bitt loose.

UPDATE 2/12/17: The Ghostbusters Station 6 fan film utilized this section. Check it out on YouTube at https://www.youtube.com/watch?v=RHMUsQqLmRg. This full-size, 3D printable synch generator's details are based on Steffan Otto's plans, found at...

Remixed and remodeled original valve holder to make it beefier so it would stand up to cosplay. ...