pronterface ender 5 plus 3d models

I wanted to attach my Ender 5 Plus to my IKEA Lack table cart. I made these, so I didn't have to drill through the printer frame and the top of the Lack table. ...I used these clips: https://www.thingiverse.com/thing:4091348

My take on the ender 5 plus liner rail. Used it before going to the Merc 1 setup.Heat Inserts are required for this to work well. It GRIPS the Y gantry well, I was able to have serious speed compared to OEM Setup.

This is to relocate the stock touch screen on the Ender 5 Plus.I relocated my electronics to a back plate and thus had to make a separate mount for the screen as i removed the original electronics casing.screws together with M3 screws and a single M5...

I removed the stock cooling fan from the motherboard area of my Ender 5 Plus and replaced it with an 80mm fan. This shroud allows it to sit at the side of the box and uses the existing slots on the side. Vastly improved cooling and much less noise...

My desing of a toolholder for ender 5(plus), it just snaps on the rails i print it in 3 walls and 20% cubic infill takes about 2 and a half hours,has slots for the stock hex keys the wrenches the spatula the sidecutters and some extra slots to hang...

More thorough print to cover more of the Ender 5 Plus bed for level testing. Note that the .gcode doesn't prime or skirt so the first disk may not print complete as the filament starts to come out. ... Be careful with where you have your clips for...

Relieving tension on the hot bed cable of Ender 5 Plus requires this modification. No fasteners are required for this setup. Printing without supports is also possible using this method. ... This idea was inspired by BGDog's design, which can be found...

A little support for the heatbed cable on the ender 5 plus, this support can be mounted to the printer with no dismantelment needed. ... Uses a M3 umbraco bolt, with a M3 nut, also need a small zip tie to fasten the cable.

Simple 5015 fan mount and duct for the Ender 5 Plus.  Compatible with the stock metal shroud & bl-touch mount and does not interfere with stock x-stop or belts. ... Only necessary modification is to remove one of the mounts on the 5015 blower fan...

... very soft and flexible materials due to the shorter bowden tube. The only additional hardware needed for this modification is longer M4 bolts, at least 15mm long, qty 2. These brackets will only work for an Ender 5 Plus. ... Happy printing!

Reworked the bottom to fit a bit better to my Ender 5 plus and made it a bit sturdier. Also resized the holes to fit some brass thread inserts in M3. ...All other needed parts can be loaded from the original source or the remixes.

Use the longer one for both front and back if you have an ender 5 plus. The light bar is long as I wanted as much light possible on my ender 5 plus. If you need less of a strip, just resize it in your slicer. Ender 5 plus has a huge print bed. If...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

Ender 5 Plus motherboard fan bracket. Use 4 self-tapping screws to attach the holder. It is possible to use two cheap 12V fans connected in series and connect them directly to the motherboard at the 24V output. ...Use 8 M3x14mm screws to attach the fans...

A simply but useful frame clip for Creality Ender 5 Pro / Plus or similar frames. I used it to tighten cables. Works fine. Very easy to print, functional and doesn´t waste filament. You may stretch the Z-axis to get an wider clip. ...

I build a custom Bowden and cable holder for my Ender 5 Plus, drawing inspiration from https://www.thingiverse.com/thing:3625215 but realizing it wouldn't work with my specific printer model. ...I redesign it entirely to create a perfect, stable fit.

This is a remix of zarify mount https://www.thingiverse.com/thing:4087221 but made to fit an Ender 5 Plus It wont quite clear the hot end but does a good job and doesn't require and additional hardware. ... the cover is friction fit and you may need...

Here are 2 Axes Fans Carriers for printer Ender 5 plus. They are design for Fan 92x92x25 / 220-110 Volt able on AliExpress for example. That's perfect to decrease the temperature of Axe motor specially when you print for a long time. ... You can...

A slightly modified belt tensioner body to fit on the Ender 5 Plus X axis carriage. ... It still requires the nut and thread part of https://www.thingiverse.com/thing:3601830 and this spacer to fit the stock bearings with an M5 bolt:...

Fixed some slicing errors Simple Cable Management box to hide the cludder on the Ender 5 Plus. Wire pass-through on the back and bottom. ... The lid can be fastend with M3 Bolts Mounting holes to fix the box on the extrusion are provided Walls...

I removed the little bucket for the SD card and USB drive since I use Klipper and a Raspberry Pi 4 on my Ender 5 Plus. ... Designed this because over time the original I remixed from lost its grip on the 2040 extrusion and started to slide down the...

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.</p> Category: 3D Printer...

I completely remade his mount from scratch to work with the Ender 5 Plus (though presumably, it would also work with other Ender 5 models) This Thing only comes with the bracket and modified BL touch bracket. You still need one of his cooler fang...

Can be used for Creality Ender-5, Ender-5 Plus, Sovol SV05, and maybe other printer with similar shapes i dont know. Supports required from build platform. Mounting on the 2020 profile using T-nuts, 5 holes available, I only use 3 mounting points...

... to increase the sides to 3mm instead of 1.5. I also increased the thickness on the mount for the Ender 5 Plus because I found that the original "wiggled" too much on my printer when mounted. ... I added two additional screws to the block as well.

I needed a filament guide when I upgraded my Ender 5 Plus to direct drive. With this I could have the filament spool sitting the same place as before. This is mounted instead of the old extruder. Hardware required: 2 x M3 Bolt 2 x M3 Nuts M6...

Inspired by a fantastic video from Tripod in his garage, where he provides an extremely detailed walkthrough of installing Bigtreetech's SKR 1.4 into an Ender 5 Plus, based on KAY3D's Cheetah 5.0 Marlin Firmware. Since I had acquired several SKR 1.4...

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...

Work in Progress Remix of the TeachingTech Concept: Please note that this concept differs from the original due to the specific format of the Ender 5 Plus! To build a case for the Ender 5 Plus, you will need: - 4 V-slot profiles of 495mm - 4 V-slot...