pronterface ender 5 plus 3d models

... can install the box more easily. Print Settings Printer Brand: Creality Printer: Ender-5 Plus**Rafts:** Doesn't Matter Supports: Yes**Resolution:** 0,2 Infill: 20% **Filament:** Doesnt Matter Doesnt Matter Doesnt Matter Category: 3D Printer Parts

The one included with the kit is for the Ender 5 (non Plus) and did not line up correctly. Micro Swiss support sent me this STL and gave me the ok to Share it an post it here. ... Thanks to Micro Swiss support for supplying this so quickly and...

I prefer 3D printer accessories that don't need extra hardware, so I designed all mine to simply snap onto the 2020 aluminum frames of my Ender 5 Plus printer. This pliers holder snaps right on and stays put, keeping it within easy reach as I always...

Creality Ender 5 Plus 2020 2040 Cable Covers Will suit any 2020 / 2040 sections (This was 100% infill) All parts are thin and weak but with care they work well. Remove using a paint scraper under the edge near the clips and twist carefully. Creality...

... the clip stress area. Print time 2:46 using PETG Head temp 240C, bed temp 80C I found the original liked to lift one end with a lower bed temp and thinner profile. Stock Ender 5 Plus glass bed (smooth side) with BedWeld applied. ...

Ender 5 Plus Z motor cover in two parts. Fits between the coupling of the Z screw and the motor plate. It fits around the motor shaft to prevent debris from getting into the motor bearing. ...Ive made it with 4 holes for 1.75 filament, small screws or...

I did a remix of the Ender 5 plus hemera mount https://www.thingiverse.com/thing:4026886. but found that the nozzle was sitting higher then the wheel on the rail making it impossible to level. so I lowered the mount holes by 3mm and that gave me...

This display holder was specifically designed for a Big TreeTech TFT24 V1.1, allowing it to be mounted in an Ender 5 plus. ...To install the new holder, removal of the old display is necessary so it can be easily seated.

This is a mounting plate for the Bigtreetech SKR V1.4 Turbo to be mounted in the Ender 5 Plus. As shown in the pictures, this plate centers the board in the chassis so that you can run cables where ever you like. ...This is more universal since you can...

This gasket has the screw holes oversized and spaced to fit the stand-offs in the Ender 5 Plus's case. ... I noticed a slight whistle and visible gap between my fan and the case; it probably would not be an issue for most people but my printer is in...

This will adapt the stock screen mounting to a BTT Pi TFT 43 4.3" Raspberry Pi Touchscreen on the Ender 5 Plus. I run Klipper with Kliperscreen and it works flawlessly. Adapter brackets center and hold the screen where it needs to be. Gives a...

Ender 5 Plus bed cable support. Wanted one which was simple, solid and didn't require additional parts. To install just remove the two screws on the bed frame, slide the support in and reinsert the screws. ...The screws don't touch the support, they...

This is for the Ender 5 Plus with linear rails with a Micro Swiss Direct Extruder mounted. To mount the Switch you must thrill 2x M3 screw threads. I hope this Thing is useful for you UPDATE: V2 now available I had Problems with the...

A custom bracket designed to securely house the stock Ender 5 Plus filament sensor following a direct drive upgrade, also incorporating a built-in filament dust filter assembly for enhanced print quality and reduced maintenance. ... The mounting arm...

SKR PRO board holder for Ender 5 Plus printer.It does not require mechanical modifications, the cables to the drivers can be stored under the board.Use the original holes and screws to attach the bracket. ...Screw the board to the holder with a 3mm...

However, the following text has been rewritten: The Enders 5 Plus bed is connected to a cable that keeps it safe. ...To secure the cable, just snap it into place in the square hole and tie it up with some cable ties, just like you see in this picture.

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ... Will Need: 10mm Magnets ...

Im Rahmen meines Ender 5 Plus Umbauprojektes, musste ein Adapter für die neue SKR 1.4 Turbo Platine. Der Adapter hat noch eine Halterung für die SD Verlängerung von Creality. Für die Montage werden, 3 M3x8 Senk, 4 M3x16 Zylinder und 4 M3x6...

This is a Remix of a Cable Support for the Ender 5 Plus. But i didnt find that Thing again on Thingi. I just made the space between the holder bigger so it fits with the original BL-Touch Plate. ... You have to ad support to the holder but not to...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ...Will Need: 10mm Magnets 3mm...

The Ender 5 plus's location on this design smacks the Bl touch on the Z rails when homing, moving it out of the way but still requiring offset changes to avoid hitting the left-hand side Z rods. ...I adjusted these offsets in the starting gcode within...

This adapter makes it simple to install the Mean Well RSP-500-24 power supply unit in your Ender 5 Plus machine. You will need (8) M4 x 8mm button head screws and (4) M4 nuts for this installation. The adapter does not demand that you extend any...

Copy of cable guides that came with the Ender 5 Plus for the X-axis stepper and limit switch cable. ... It allows the cable to slide through as the gantry moves back to front.Should work with any 20 mm aluminum extrusion framing.

This is an external mount for the 500W Meanwell power supply ( RSP-500-24 ) that comes with the Ender 5 Plus. It consists of a top cover, bottom cover, and power switch/plug holder with a cover. The power switch/plug holder uses the existing power...

Melloow Fly 4.3" Display mount for Ender 5 plus Achtung: BITTE lies erst die Beschreibung aufmerksam durch auch die Dokumentation in dem Download Ordner falls vorhanden. ... In eigener Sache: Ich freue mich das du dir meine Designs anschaust und hoffe...

This is a rapid and makeshift spacer designed to enable an E3D Hemera Bowden to be securely attached to an Ender-5 Plus printer. ... It shifts the stock filament sensor away from the extruder bracket, allowing its filament path to align perfectly with...

Ender 5 Plus BTT smart filament sensor mount, this goes in the place of the stock sensor and uses the same M4 bolts and T nuts. ...Wire management for the hot end wiring to bring the wires off of the back extrusion to make way for top enclosure.

This is a DIN rail mount for the Ender 5 Plus MOSFET.  It is a snap fit and requires no hardware to mount the MOSFET, though M3 screws could be used if you want.  I printed mine out of PETG for a bit of flexibility. ... STEP file included incase you...

This mount seamlessly integrates both the BLTouch and filament run out sensor that come standard with the Ender 5 Plus. It attaches securely to the stock metal mounting bracket, so I'm confident it will be compatible with every printer in the Ender...

A few changes were needed to get this to fit on my Ender 5 Plus. I went with spacers to adjust the Z. On the Micro Swiss Direct drive there was no need for the cut out area so I removed it to increase strength. This will print with no supports .