pro tube vr 3d models

With my FlashForge Creator Pro, I've found that the tubes often don't fit snugly on top of the plate. To make matters worse, they sometimes fall off on their own. Frustrated by this issue, I decided to give DrLex's design a remix in an effort to...

There are other good designs different than mine on Thingiverse too, I designed mine the way I did so I wouldn't have to unclip the guide tubes at all, even though that is a very easy process. My design uses about 4 meters of filament and takes less...

Primer Tube holder for tubes outfitted with the Double Alpha Academy magnets. ...

I noticed that the bowden tube is not well supported on a stock Creality Ender 5 Pro so I created this simple clip/holder to give it a bit of extra support. No screws needed, it just slides over the tube and sits on top of the hot end support...

The Koss Porta Pro headphones are a must-have, but you can also use fake speakers from AliExpress for around ten dollars. However, soldering is necessary for their installation. ... To manage the cables, I employed thirty-eight millimeter wide hook and...

... 60mm in length and are spaced 81mm center to center. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20mm or less Infill: 15% - 100% Notes: The model was printed upside-down with adequate support throughout.

Cut a precise PTFE tube using a hobby knife.

I purchased the D2 Pro solely to discover that I couldn't see clearly with them, despite having excellent vision. Therefore, I wanted to develop a subtle method of incorporating focal length. Designing it was the first step, followed by printing and...

Looking for a straightforward, robust and efficient FlashForge Pro Creator filament guide holder? You've found it! This is a no-nonsense replacement that's strong, lets you position it however you want and doesn't get in the way when you're working...

Looking for a simple, straightforward and highly effective FlashForge Pro Creator filament guide holder? You've got it right here. This uncomplicated replacement is robust, lets you position it however you like and won't get in the way when you need...

Before installing this part, ensure that the filament tube fits snugly into it. If it's too loose or too tight, don't worry – simply heat the part gently with a hot air gun or hot water and push it in place for a perfect fit. To mount the part,...

Set your slicer of choice to have a strong part (top/bottom/shell layers, temperature, infill, etc). Before installing this part, make sure your filament tube fits it nicely. If it's too loose or to tight, no worries, just heat the part gently with a...

I tweaked the file so the filament tube won't come crashing down anymore. ...Built a tiny shelf for the tube to safely rest on, securing it firmly in place.

For Elegoo Neptune 3 ProTo cut the PTFE tube exactly to the size of 54.8 mm

I got kind of annoyed with all the other tube holders having logos on them and thought i could also make them a little bit better. It has no logos. It is just a plain tube alignment mod fit for FlashForge Creator Pros. ...Also i realized that the other...

At the entrance to the hotend, thread a filament tube so that the filament does not enter the hotend at an angle.

Habe die Filmanentführung grösser gemacht, damit ich keinen zusätzlichen Schlauch benötige. ... Made the filamen guide bigger so I don't have to use an additional tube. ...

the tube of the sprite extruder is 18mm, you must add a tube of ptfe or capricorn of 26mm approximately to the base and then cut with a cutter, the piece helps the cuts to be perfect 90° to then put in your hot-end.

This is for the bowden tube at the extruder side. ... You need to block the support in the ziptie slots, but the overhang needs support and the support in the last ziptie slot can be taken out from the bottom

A simple bracket to move the filament guide tubes away from the rear centre of the printer to the rear (or front) corners. ... Uses two existing screws for mounting

Just a simple bracket to bring the filament tubes outwards for easier use, and to prevent the filament from slipping off the spool and getting tangled between it and the machine. It also utilizes the stock filament tube holders for easy installation!...

Just a simple bracket to bring the filament tubes outwards for easier use, and to prevent the filament from slipping off the spool and getting tangled between it and the machine. It also utilizes the stock filament tube holders for easy installation!...

I figured I could come up with something even better, so I set out to create a plain tube alignment mod specifically designed for FlashForge Creator Pros. ...As it turned out, I also noticed that most of these mods didn't fit my unique machine, which...

... require more complex printing, necessitating supports, etc. I did use a raft because the base is very thin, but trimming the end would likely allow printing without it. Printer settings: Printer: Flashforge Creator Pro Rafts: Yes Supports: No

Printing Professionals Can Rely on This Reinforced Snap Tube Holder Design as a Straightforward Substitute for Conventional Units. Built with Identical Screws, It Optionally Integrates Securely Using Zip Ties. If Working from Smaller Spools That Are...

This adapter was specifically designed to seamlessly connect my Palette Pro to the Ender 5 Plus. The installation process is straightforward and hassle-free, yielding a quick print that doesn't necessitate any supports. To secure it in place, simply...

Since West Coast Products currently (February 2022) lists their 1x2 tube plugs as out of stock until March (which is too late for this build season), I made an alternative optimized for printing. The holes are made to fit EZ-lok 10-32 x 7/32” depth...

Remixed the Ender 3 pro filament runout sensor by blaiseb with slot for bowden tube.

We designed the Teflon tube clip needed to connect the Palette 2 to the Raise3D Pro 2.The length of the Teflon tube is medium. ... Additions M3x20mm bolt x1 or x2 Teflon tube clip Grommet x1 or x2

The extruder heads on my Flashforge Creator Pro were manufactured to accommodate 6mm PTFE tubing. ...Unfortunately, I only possessed 4mm tubes, prompting me to construct a custom mount that can securely hold these smaller-diameter tubes in place.