pro relocation 3d models

The goal of this bracket is to move the power supply on the Ender 3 or Ender 3 Pro off of the Z axis frame and down onto the base of the printer. This is to reduce the weight on the Z frame in hopes of getting better acceleration performance and less...

This kit allows you you re-locate your power supply under the bed. This enables upgrading to dual Z lead screws while keeping your power supply connected to your printer! This kit also includes an upgrade to "squash ball" feet - this is required...

This is an esc and rx relocation mount for the redcat gen 7 pro. It enables you to remove the factory steel cage that the esc and rx are mounted to, using the factory plastic retainers instead. The retainers can be screwed directly into the new...

It's support for relocating your PSU on the MeanWell Creality Ender 3 Pro with a double Z-axis and double Z-motor installed. You'll need two M4x8mm screws also. Another hole must be made in the back side of the original cover to accommodate the...

I wanted to move the LCD more to the middle of the printer to reduce the printer's overall size, so I designed this adapter to make LCD relocation as easy as possible while reusing stock equipment as much as possible. ... Of course you may need to...

I upgraded my Orange module DSM2/DSMX/Walkera compatible by stripping down the standard module cover, which wasn't working properly for me. ...So, I took just the antenna section and attached it directly to the original cover using some glue.

I designed this bracket to relocate the filament run out sensor to the middle so the angle of the filament is centred when having 2 spools fitted. ...Print on its side to avoid layers from separating.

In preparation for a dual Z motor mod, I needed to relocate the power supply to a different location. Upon closer inspection, the supply fit perfectly below the printer when oriented sideways, prompting me to design a two-part holder that mounts the...

After suffering through this mistake firsthand, I crafted an antenna relocator that serves multiple purposes. Firstly, it provides a sacrificial component to break in a crash, significantly stronger than the original connection. Consequently, I've...

when I tried to install the Biqu h2 on my Ender 5 pro the motor hit the body of the printer and the end switch on the x-axis was not reached so I decided to print a new base for it with adjustable space you can use it for any other axis

This is a design intended to install a Raspberry Pi permanently into the Tevo Tarantula Pro for connection to an OctoPrint server, relocating the power supply to an upright position where it can be better cooled by surrounding air rather than...

A small bracket that allows you to mount the stock spool holder on top of the printer. ... One M6x60 bolt and nut is required to secure the spool holder.

Cable cover for ender 5 pro for screen relocate and new cable Screen Relocate : https://www.thingiverse.com/thing:4600011 SD adapter : https://www.thingiverse.com/thing:4670609

###Why use Use this bracket to relocate the Auto Bed Level Sensor on the Tronxy XY-2 Pro in order to use other heater blocks like Volcano which allows for faster print speeds. Model has multiple mounting holes for the XY-08N Sensor for optimal...

When hanging the power supply, the powerplug "hanging" did not work for me,

a mount to relocate the psu of ender 3 pro if you want to add dual z-axis Lets you use 2 or 4 t nuts to mount the bracket to the extrusion instead of pushing it along from the end. ...Also has been extended to cover up a gap which ~might~ have let small...

This is an LCD bracket designed for the Griffin Pro 1.0-2.0 with a relocated power switch to the LCD rather than the side of the printer. Testers should be aware that this has not been thoroughly tested and they assume all risks. Modifying the...

Remix / recreation of https://www.thingiverse.com/thing:4852456, that allows you to remove the top front bar of the X5SA (pro and non pro) and reroute the belts so that they don't interfere with your view of the printhead/printjob. While I have...

You will need to mod the carriages as per the original thing, you will also need to relocate the Y endstop and extend the motor cables. I heavily advise that you reinforce the corners of your printer, as removing the top bar wlll probably make the...

New fan shroud I designed to allow for the best airflow to the nozzle and be adjustable for volcano/non volcano setups. This allows for the use of the existing lower screw that used to be to hold the fan in place and now be used as a position...

A simple mount that allows you to relocate your extruder to the top of the printer. Makes the gantry a bit lighter and works best with a top-mounted spool holder. Only stock parts are used. Both the motor cable and the PTFE tube are long enough and...

I have made this Creality CR-10S PRO V2 filament guide after trying different design that were already made by other creators without to much luck. There was always some problems/wear even from my own remix. And I wanted to move to the left the...

<p>Need 2 M3x4 Heat Set inserts .&nbsp;</p>

This mod is relocating stock spool holder to the right side, lowering printer height and mass center, which leads to significantly reducing print vibrations.Stock location of spool holder is shifting printer mass center toward rear top and adding...

Mount adapter for moving stock spool holder to right front corner, increase print stability and reduce printer dimensions of Neptune 3 Pro.It is fully compatible with console relocation adapter: https://www.thingiverse.com/thing:6394743Mounting brace...

stock bracket interfered with the part cooling duct used two m3x10 bolts, stock may work, i didn't try switch mounts are threaded, re use stock hardware here print with the long flat edge touching buildplate supports touching buildplate...

<p>stock bracket interfered with the part cooling duct</p> <p>used two m3x10 bolts, stock may work, i didn't try</p> <p>switch mounts are threaded, re use stock hardware here</p> <p>print with the long flat edge touching buildplate</p> <p>supports...

dual Z ender 5 pro screen relocation

... 40x40 Fan. ... Don't work with E3D Titan Extruder. Works in progress... 01-Apr-18 => update: 3D Models added. Remixed From CR-10S extruder relocation plate and filament sensor housing by xxFRESHxx CR-10 extruder relocation bracket by wayneuk

This relocation mount uses the v-slots in the extrusion frame and it utilizes the spool holder that came with the Ender 3 - Pro as well as the nut and bolt that is used to mount it in the original position so no other hardware is needed. ...I've found...