pro ject essential ii 3d models

My attempt at replicating the wonderful Pro-Ject Essential ii Record Player on CREO, later rendered on Keyshot.See the first design iteration animated in the linked video. ...Let me know what you think!Instagram @jw.pde

My attempt at replicating the wonderful Pro-Ject Essential ii Record Player on CREO, later rendered on Keyshot.See the first design iteration animated in the linked video. ...Let me know what you think!Instagram @jw.pde

Pro-ject Xpression II VTA shim I printed out Oneunder's Pro-ject shim but I believe it was designed for a newer style tonearm as it did not fit. ... I designed this to be a .125" shim that I required after changing the platter from the original steel...

PRO-JECT turntable

I needed to change the VTA of my Pro-ject Debut III, which doesnt have that adjustment built in. This shim will add around 1.5mm of height to the tone arm. ...

This is a simple support for the Pro-Ject turntable, just use a little double sided tape to secure the support down and place your turntable feet within the cup to stop it sliding around when you open the lid. ... This is still a work in progress and...

Small manual fine tunning for the antiskating of Pro-ject, Music Hall and other types of turntable. You can adjust the weight either with the size of the objet or filled of the piece. This object was made in Tinkercad. ...Edit it online...

Pro-ject turntable acrylic covers printed in sets of four fit perfectly on models such as E, RPM1/3, RPM5/9, 2.1, and 1.

Pro-Ject fixed this by shipping the machine with a large platter, but I thought I could do better. This works very well, sits flush on the machine and redirects the exhaust down. Snaps on and off. ... Designed to be printed without supports on a...

... equiped with a strip with a width of 7 mm max and a height of ca. 12 mm max. If you want to be able to close the hood of your Pro-Ject with the lighting installed you might have to solder a flat cable to your strip as i did, just check the photos.

... accuracy in use. The T1 comes with a pre-adjusted Ortofon OM 5E Moving Magnet cartridge, ready to use right out of the box. Super shielded, semi-symmetrical, low-capacitance Pro-Ject phono cables are included. ... Dimensions: 415x100x335 mm (WxHxD)

The Pro-Ject VC-E is a great, small Vinyl washing machine with one constructional fault: After washing some vinyl records the wet air from the used water tank blows to the underside of the record and makes it dirty again. This is a kind of exhaust...

This is a simple base to attach a stripe led and then place it under the acrylic plate of a Pro-ject debut carbon. You can simply lay it over your turntable without having to use any adhesive, as you can see in the photo (Only temporary applied a...

The Pro-Ject VC-E Vinyl Cleaning Machine famously has a major design flaw in which the vacuum exhaust port blows air straight up into the bottom of the freshly cleaned record. I've seen numerous posts on audiophile forums in which plastic bubble...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/eGmplNntu5Y

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/jHXMe2rPyTA

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/eGmplNntu5Y

Hi i got some low freq vibrations on my tonearm so i designed a fluid damper, it is for the 9 inch aluminium arms of many pro ject turntables. IT grabs on the arm vith 2 o-rings ad wraps around the base with friction. ... if the height does not mach...

This is a double washer to fix issues with the hinge on the dust cover of Pro-Ject Debut line turntables. The issue is that when the hinge is too tight it will not open properly, and when it is too lose it will start to pull the hinge screws out of...

Finally I gathered that it's not the record but the player and I noticed the belt of my trusty Pro-ject Debut III to have worn down pretty badly, going dry and porous and slippery and stuff. Yet another faulty device that can only be fixed with...

Pro-ject VC-E is a record cleaning machine to wash and vacuum vinyl records. It is excellent overall, but has one issue with the exhaust blowing dirty water up at the bottom of the record. This is an exhaust duct to redirect the airflow out and down...

Essential Upgrades for Ender 3 Pro WARNING: This project has been put on hold and may not be completed anytime soon. I still respond to inquiries and provide finished designs upon request, but no new work is being done on this upgrade package. Your...

The complete dimensions mentioned on the official site were utilized by me; however, no particular layout was provided. ...Nonetheless, I believe that this information is sufficient to create an attractive room design.

Just needed a more relaxed arm rest from my new turntable. This design gently supports the carbon fiber arm without "locking" it and IMHO the original design is better suited for transport. Being a so light and delicate carbon fiber arm, I prefer...

This is the first version of an air exhaust for the Project VC-E. ...Some printers may have difficulties without support for the wide roof part.

# GoPro support for Xiaomi M365 (Pro or not) **To support my job, follow me !** Youtube: http://m.youtube.com/c/ClementsProjects Instagram: https://www.instagram.com/clementsprojects/ Versions : - V1.0 (08-04-2021): - Creation of the files (Works...

Here you have a dummy of the TMotor F40 Pro II Motors To use for your custom builds You can find this product here: https://www.banggood.com/custlink/mDDGEh1sTL

Here is a dummy model of the TMotor F40 Pro II Motors designed specifically for use in your custom projects. ...You can easily locate this product by visiting the following webpage: https://www.banggood.com/custlink/mDDGEh1sTL

The Numark Mixtrack PRO II is a DJ controller that I possess, and I attempted to model it in Catia V5 at a 1:1 scale. Here's my result! Additionally, I've included an STP file with the combined CATProduct as a separate CATPart. ...Enjoy!