prius phone mount 3d models

I printed a bracket to mount my iPad Mini on my Prius C 2012. It's technically possible to attach anything that the magnet can grasp. A hole for the magnet is included, with a diameter of up to 18 mm and approximately a 5mm thickness. ...The bracket may...

The Prius C has a weird pocket directly behind the steering wheel that doesn't work for phones at all. I designed this holder to support a variety of phones. The preferred (more stable) position is to dock the phone on its side. Drop the holder in...

i-Phone dock for Prius...

This model is used for toyota Prius (2009-2016). It is mounted on te ventilator gaps in the car. Usefull and doesn't block any view (surroundings). ... The material that i used was Carbon, because it's resistant and merges with the interior.

... have built in electronics so just a power cord to a 12V plug is needed. ... Double sided tape would be placed in the recessed area on the bottom of the mount and the mount would be specifically place on the dash as indicated by the imagery attached.

i phone dock created in Alibre Design

This sturdy phone holder easily slips into the compact storage compartment located directly behind the steering wheel on my Toyota Prius C, perfectly accommodating my OnePlus 5 smartphone without any protective case. ...To secure the mount firmly within...

Brodit Car Brackets For Toyota Prius Mobile Phone Extension Bracket Printer Settings CEL Printer: Robox Printer: Raft Options: No Raft Necessary Supports: Printable Yes Layer Resolution: 50 Micron Layer Thickness Infill Density: 40 Percent Infill

I created it to fit snugly into the small compartment at the front of my 2014 Prius V center console, just below the standard 12-volt power outlet. The design requires two side panels: one is integrated directly into the main body, while the other...

This car holder secures snugly within the compact storage area behind the steering wheel of my Toyota Prius C, tailored to cradle the Samsung Galaxy S10e perfectly, even when it's encased in a slim protective cover or left bare. ...I opted for robust...

... I was inspired by this awesome phone holder on Thingiverse: https://www.thingiverse.com/thing:2187682. ...Having that for a few days gave me time to think about what features I really wanted in my own design, so I incorporated them into this one.

I designed a remix of the Youkai Toyota RAV4 dashboard phone holder, which I 3D printed using PLA material. ...However, I highly recommend utilizing ABS for this project due to PLA's tendency to melt under direct sunlight exposure.

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=332106 Instructions Using the following options: text_itself = Prius text_alignment = embossed text_size = 7 text_font = Knewave.dxf show_text = yes

The specifications used for this personalized object include a lip of 0.4, "Prius" as the text to be engraved, no build plate selector, a length of 50, "Letters.dxf" as the text font, a ring radius of 1.6, a ring thickness of 0.8, a height of 1.6, a...

Easy-to-use wall mount for your Toyota Prius Plug-in's wall charger, designed to simplify daily charging. ...Simply slide the charger up or down from its convenient mounting point, making it easy to grab your cord on-the-go.

I use this: [Magnetic Mount](https://www.amazon.com/dp/B07S61CV3X/ref=cm_sw_em_r_mt_dp_A6M50T99RDRGY7GC0CXJ?_encoding=UTF8&psc=1) You can remove the sticky bit and use a longer screw(M4) and washer to permanently secure the swivel. ... You should also...

Update, 3/14/2021 - Just wanted to update this and say that this phone holder is working really well in the Prius Prime. Enjoy. Update 5/14/2021 - This version of the popsocket holder has been in my car for two months. No problems with this...

... fit for my 2005 Toyota Prius, placing it neatly within the cassette player, which is no longer in use. ...Designed to resemble my Chinese-made phone, the Bluboo, it boasts a 6-inch display and can be easily modified to accommodate other phones as well.

Remix of phone holder for Prius C cubby in front of steering wheel. I sized it for a Pixel 4 XL with case on. Also works pretty well for an iPhone 11 with case. I increased height of sides so phone is less likely to tip out on a sharp turn. ... ...

... both horizontally and vertically (on the left side). Added a second connector compared to the original design due to more plastic and width of the phone holder itself. ... The design is a little rough around the edges but prints and fits well.

Designed for an iphone 6+ and a prius v. Fits both horizontally and vertically (on the left side). Added a second connector compared to the original design due to more plastic and width of the phone holder itself. The design is a little rough around...

I wiped out the end that held the other phone and shaped it to fit my iPhone 14 with a case on. I used PLA the first time and it was fine, except on really hot days, the holder would warp when sitting in the sun. I just made it again from ABS and it...

... case holder behind the steering wheel. ...The adjustable wings will securely hold your iPhone in place, accommodating various phone models with ease. ... Print Settings Printer Brand: Robo 3D Printer Model: R1 PLA Raft Setting: Yes Support Setting: No

Phone mount you can use to prop up your phone for scrolling!

This was a phone mount I created and it fits about any phone on the market and can even probably fit your phone case too! ...Fits a good selection of screws that could drill into a 2 by 4.

Charging Station Companion: A Hands-Free Phone Mount Designed to Keep Your Device Safe and Secure When Plugged In

This versatile phone mount fits seamlessly onto your camera tripod, perfectly accommodating phones that are just 1 centimeter thick or even thinner. ...For those with slightly larger smartphones, simply scale the design to suit your device's unique...

Our innovative Phone Mount addresses two common issues: cord fraying due to bending and inconvenience while using counter space. The slanted base supports the phone, while arcs at the bottom ensure easy charger access. Adjustable clamps with springs...

A generic phone mount with screw attachment for universal mounting. By default this design comes with a mic stand adapter, and I'm working on a car adapter. The phone is attached to the adapter with a single M3 screw so the adapter should incorporate...

The mount is designed so your phone can simply slide in and out of the mount freely and the mount is very easy to use. The mount would be constructed out of plastic and be able to be 3D printed and easily assembled. It can also be removed and the...