printrbot simple 1405 3d models

Didn't spend two days getting every single angle just right on your brand-new Printrbot? (didn't shell out for a metal one?) Don't look elsewhere! This was printed with NinjaFlex to absorb vibrations and increase the friction between the table and...

Instead of drilling holes in the machine to install a manual switch, I created this simple plug-and-play device. It's designed to be mounted on the front of the printer, using the existing holes that are already there. I chose a standard single-pole...

This part substitutes Part 1115 on the Printrbot Simple 1405 Maker's Edition. Printrbot offers the 11" x 3/8" Acme Rod, Acme Nut and 5mm to 3/8" inch Coupler for larger Printrbot Models, allowing you to use these parts with your Simple Makers...

This is a replacement for Part 1115 on the Printrbot Simple 1405 Maker's Edition. Printrbot sells the 11" x 3/8" Acme Rod, Acme Nut and 5mm to 3/8" inch Coupler for larger Printrbot Models that can be used on your Simple Makers Edition printer. This...

... my own hands. ...Currently, only two essential components of the foundation can be found here. The rest of the necessary parts can be accessed at their original source on https://www.youmagine.com/designs/1405-simple-x-expanded-single-double-precision

Add the foot by replacing each of the existing Printrbots's M3 screws for each foot you wish to add then insert a new foot followed immediately by reinserting that same screw and tighten it in place. This setup provides additional stability for...

Here is a simple mount for an 80mm fan that blows directly on the Y-axis stepper motor of your Printrbot Maker's Kit 1405.

This is a custom mount designed specifically for my Printrbot Simple Maker 2014 (1405) and its E3D v6 hotend upgrade. I based it on a previous bowden design available at http://www.thingiverse.com/thing:415781. It uses four ten-millimeter M3 screws...

This Thing is a model 1:1 model of the Printrbot Maker 1405 (2014) edition, one of the newest kits offered by Printrbot. When I started to look into designing my own mods I noticed that there was a lack of models for this particular version of the...

This is a specialized guide for Printrbot Makers Kit Model 1405 owners. It attaches to the rear screw on the "Y TOP BACK" part and requires precise placement to ensure secure hold. Following each print, insert the screw all the way into the...

Testing a Z-axis Isolator on the Printrbot Simple Installing this feature might need some tweaking. ...It needs two M3 x 30 or longer screws and an 8mm flat washer to work properly.

The project printed in about 30 minutes on my trusty Printrbot 1405 stock machine. You simply snap it onto your Z-axis bars, securing it with the long notched end facing you. Next, feed the filament through the first eyelet, then insert a small piece...

... kit, If you use it, I didn't upload "15.STL" file; so, print one of each STL files still remaining. If you need assembly instructions or a list of the required hardware, check Printrbot's site: http://help.printrbot.com/c/2014_Printrbot_simple.

For assembly instructions or a list of required hardware, check Printrbot's site at http://help.printrbot.com/c/2014_Printrbot_simple. This is still a work in progress (I'm a beginner with CAD and computer drawing), so please let me know about any...

Meanwhile, an M3 screw already mounted on my Printrbot gets secured by loosening it by 2mm, allowing the bracket to slide into place seamlessly before re-tightening it snugly. ... Printed with precise care using a layer thickness of 0.40 mm and...

The original frontend is replaced with one that uses the stock 1405 wooden mounting plate, which keeps the extruder's heat away from the plastic components and stops melting/warping. The modification includes a slightly changed YZ plate where you...

It was designed to pair perfectly with the standard 1405 Stock, rather than the No Sag Mod model. Warning: The Y switch position is not ideally located near the extruder motor and has caused the belt to come into contact with the printed part in...

This is a set of mounts to hold a 3/4 in PVC pipe to the side of a printrbot for hanging a spool over top of the printer. You should just need a short chunk of PVC and an elbow. The screws on the side of the bot will just barely grab the nut so be...

If you have the PrinterBot 1405 with the XL upgrade, this part adds significantly more height in the Z direction, giving you around 20mm of extra room. You can clearly see from the pictures that the wood frame is literally the only thing holding it...

Yet another attempt at an X axis extension for a Printrbot. I aimed to reutilize the initial plate, yet still allow myself the possibility of utilizing 400mm rods so future extensions would remain feasible. Instructions Print...

I modified an existing extruder fan mount (check out remixes) that refused to fit the simple 1405 and kept falling off. To fix this, I streamlined the geometry (scrapping some unnecessary vectors), stripped away excess material blocking its...

Inspired by Brook Drumm's release of STL files for Printrbot Simple parts (available here: http://printrbot.com/2013/07/04/sneak-peek-simple-files-for-hackerspaces/), the user imported these files into Tinkercad for simplified prototyping of...

I just modified Jon Lawrence great design to be able to print it on my stock simple. Just wanted to share if any one else needed it also. A tension block is needed from his thing files. I also recommend his belt...

This design offers an improved alternative to the traditional base piece of the Printrbot Simple 1405 Tri-Rod Mod, which can be found on Thingiverse at http://www.thingiverse.com/thing:575393. Instead of utilizing its own unique attachment method,...

Save one of those (wires with a spiraling tube).

This component enables users to move the extruder away from the print head, significantly reducing the weight of the printhead and subsequently improving print quality, especially on printers that undergo rapid direction changes. By incorporating...

Keep one wire with a spiral tube intact.

Printrbot Simple Makers Kit 1405 is designed for the 2014 model. The original hardware comes with no modifications required. Print parts fit easily within a 100x100x100mm space, no adjustments needed. Four screw holes allow tabletop mounting,...

This custom designed z-axis stabilizer is specifically crafted for a standard Printrbot Makers Kit 1405 printer. The design fits snugly onto the end of the silver rods without obstructing the Z movement of the printer. For added security, two M3x10...

I finally got my tiny Printrbot 1405 to print out the BabyNES Raspberry Pi B+ Case by cutting up jrebreiro's STL files into smaller sections - and guess what? It worked beautifully! ...All I had to do was attach everything with a strong adhesive and...