printing abs on ender 3 3d models
2661241 3d models found related to printing abs on ender 3.
thingiverse
On both of my Ender 3's the fans for the nozzle cooling died. So I decided to design a simple nozzle cooler for a 4020 fan. My 4010 was usually adequate. But I want to try it with a 4020. Maybe it will help with overhangs ;-) I printed it with ABS...
thingiverse
Quick and simple upgrade print...
thingiverse
List of materials: 2 x Corner Brackets 2 x Corner Brackets 2 x Corner Brackets 2 x Corner Brackets 4 x Small Channels 4 x Large Channels 1 x Puller 3 x Hinges that can be found here: - https://www.thingiverse.com/thing:1551631 1 x Ender Electronics...
cults3d
Simple basket and filter I designed in order to extract and filter the fumes from my DIY enclosure when printing styrene containing filament such as ASA or ABS. This screws directly on top of an 80mm fan which should be blowing air up through the...
thingiverse
I designed this as the others dont fit the latest Ender 3 pro or the they dont fit with a Ender sitting on a table without any dampening (mines as is from the box sitting on a table) Ender 3 pro draw. Unscrew the control board and slide draw into...
thingiverse
This modification enables the installation of two fans on a Creality Ender 3 or CR-10 printer, enhancing airflow and print quality.
thingiverse
Because of the poor support from creality and my broken cableclip on the ender 3 S1, i redesigned the original cable clip. ... Printed with PLA+ it should work ;)
thingiverse
An Ikea MITTLED is used as the lamp, the screws that come with the lamp can then also be used to screw the individually printed parts together. The lamp is fastened with an M4x20 or M4x25 screw and a hammer nut in the aluminum profile. ... Print...
thingiverse
... Part B using 101% or 102% scale for easier installation and fitment. -Use enclosure for printer for ABS. -Use tabs on the corner of the prints for printing ABS. ... -My printing time for every single part is around 1hour 50min with 20% infill.
thingiverse
Remix of Creality Ender 3 Dog modified by removing the base from the original file within Meshmixer and scaling it up in Simplify 3D to accommodate printing in various materials and sizes without support structures. ...So far printed in PLA Natural, ABS...
cults3d
I am sharing with you my configuration file for the Ender 3, Ender 3 Pro, and Ender 3 V2. The parameters were calculated and tested on several test cubes to get the best out of Cura. In addition, I managed to reduce the printing times by an...
thingiverse
... Once printed, assemble the parts by gluing the "PLA houder lade" component onto the "PLA houder schroefdraad" piece and then install it on your Ender 3 machine. ...This mounting bracket relies on two standard ABEC 7 bearings for smooth operation.
cults3d
I wanted to get close to the print head but only put air on the part, not the nozzle.For that purpose I used the nozzle portion of the following air duct that was made for the stock fan (https://www.thingiverse.com/thing:3255518). The channel in...
thingiverse
I wanted to get close to the print head but only put air on the part, not the nozzle.For that purpose I used the nozzle portion of the following air duct that was made for the stock fan (https://www.thingiverse.com/thing:3255518). The channel in...
thingiverse
I found the Ender-3 Minimal Bed Handle by McCynic https://www.thingiverse.com/thing:3368115 I loved the minimalist design (I'm moving the bed, not driving a race car!) but this one was designed to use the bed leveler screws. I added a clamp which...
thingiverse
- Either print 2 (ender 3 light holders) - or 1 (ender 3 light holder) and 1 (ender 3 light holder-hook) front side - or 1 (ender 3 light holder) and 1 (ender 3 light holder-rev hook) back side ender 3 light holder-hook & ender 3 light holder-rev...
youmagine
The air passing through the "closed flap" causes ABS prints to warp. I've been using a redesigned wind barrier from PrintMo that works flawlessly with ABS. If you want to switch from ABS to something hotter like PETG, PC, or Nylon (all possible given...
cults3d
This design is a mod created to avoid vibrations in our prints with the ender 3, ender 3 pro and ender 3 v2. ... It is very easy to mount, you only need a 440mm D10 rod and 3 M5x20 screws.